|
Re: Project Bad Demeanor
[Re: Hitman340]
#864439
07/29/12 11:26 PM
07/29/12 11:26 PM
|
Joined: Feb 2003
Posts: 3,456
Out West
408strokerdart
master
|
master
Joined: Feb 2003
Posts: 3,456
Out West
|
Quote:
Another.
Scoop attached to the hood or mounted independently? Looks good either way. Wasn't sure how much I was going to like that scoop on that body, but it looks good. 
|
|
|
Re: Project Bad Demeanor
[Re: Hitman340]
#864441
07/30/12 12:53 PM
07/30/12 12:53 PM
|
Joined: Feb 2003
Posts: 3,456
Out West
408strokerdart
master
|
master
Joined: Feb 2003
Posts: 3,456
Out West
|
Quote:
Its mounted To the engine.
Thinking about doing this to my new scoop also. Any pictures of how you did it? Did you build a tray inside the scoop then mounted to the engine? I don't think I have ever seen good pictures of how this is done.
|
|
|
Re: Project Bad Demeanor
[Re: tboomer]
#864448
07/31/12 09:56 PM
07/31/12 09:56 PM
|
Joined: Mar 2010
Posts: 601
Niles, Michigan
Hitman340
OP
mopar
|
OP
mopar
Joined: Mar 2010
Posts: 601
Niles, Michigan
|
Brian I hope this was some help to you.I did not have to re-flange the scoop.It fell about 3/8s lower than I would have made it but not worth what it would take to change it.If there is any way I can help please feel free to give me a shout.Thank all of you for the kind words in regards to my work.
Keith,Im pulling everything out tommaro and Giving it to Vic this weekend.Looking forward to bending the needle on your Dyno over the winter.
Last edited by Hitman340; 07/31/12 09:57 PM.
|
|
|
Re: Project Bad Demeanor
[Re: Hitman340]
#864449
07/31/12 11:25 PM
07/31/12 11:25 PM
|
Joined: Feb 2003
Posts: 3,456
Out West
408strokerdart
master
|
master
Joined: Feb 2003
Posts: 3,456
Out West
|
Quote:
Brian I hope this was some help to you.I did not have to re-flange the scoop.It fell about 3/8s lower than I would have made it but not worth what it would take to change it.If there is any way I can help please feel free to give me a shout.Thank all of you for the kind words in regards to my work.
Keith,Im pulling everything out tommaro and Giving it to Vic this weekend.Looking forward to bending the needle on your Dyno over the winter.
Definately helpful. I appreciate the pictures.
|
|
|
Re: Project Bad Demeanor
[Re: Hitman340]
#864452
12/02/12 09:06 PM
12/02/12 09:06 PM
|
Joined: Mar 2010
Posts: 601
Niles, Michigan
Hitman340
OP
mopar
|
OP
mopar
Joined: Mar 2010
Posts: 601
Niles, Michigan
|
Wow, Wished I would have turned that light on sooner.  That $hit really works. ATI rates this bad boy to hold up to 1800 HP. My little W8 would really have to grow a pair in order to break this thing. Now were just down to assembling the engine and we should be ready for spring.Merry christmas to me. 
|
|
|
Re: Project Bad Demeanor
[Re: Hitman340]
#864455
12/03/12 12:52 AM
12/03/12 12:52 AM
|
Joined: Feb 2003
Posts: 3,456
Out West
408strokerdart
master
|
master
Joined: Feb 2003
Posts: 3,456
Out West
|
Quote:
Wow, Wished I would have turned that light on sooner. That $hit really works.
ATI rates this bad boy to hold up to 1800 HP.
My little W8 would really have to grow a pair in order to break this thing. Now were just down to assembling the engine and we should be ready for spring.Merry christmas to me.
Not to bust your bubble Jeff, but I see a problem....maybe. That is the same transmission I run. They forgot to put the "spacer" between the bellhousing and trans case on mine. They made a run of sb mopar bells that were to short and they make it up with a spacer. Now, maybe you have a newer bellhousing since they said they would correct it at their next run of castings. Just check it out....caused me some grief and took lots of measurements to find out it was not my mistake. ATI kept saying I didn't have the coverter in all the way. 
|
|
|
Re: Project Bad Demeanor
[Re: 408strokerdart]
#864456
12/03/12 08:32 PM
12/03/12 08:32 PM
|
Joined: Mar 2010
Posts: 601
Niles, Michigan
Hitman340
OP
mopar
|
OP
mopar
Joined: Mar 2010
Posts: 601
Niles, Michigan
|
Thanks guys. Kenny, That is a glass hood with a carbon wrap.This is something I offer at my shop. Thanks for the good info Brian. I will be sure to give that a close look. If I run into a issue I may be asking for some of your measurements to compair befor I call them. Thanks again!!! 
|
|
|
|
|
me something good.
