YET ANOTHER HOW MUCH DOES IT MAKE QUESTION!!!
#704880
05/22/10 11:23 AM
05/22/10 11:23 AM
|
Joined: Sep 2009
Posts: 2,325 Clinton Twp... north of Deetro...
Labratt
OP
Good Ol Randy B!
|
OP
Good Ol Randy B!
Joined: Sep 2009
Posts: 2,325
Clinton Twp... north of Deetro...
|
Taking the ole' GTX into Jake's Automotive next Tuesday for a front-end alignment,and long-awaited dyno-tune session! What are your guesstimates on HP and Tq.? X weighs 3740,race weight,and runs 11.19-11.30 @ 120mph. Motor's a '70' +.040 440 block,10:25:1 Diamond Forged pistons,OTB Eddy Performers,Comp SQ solid flat tappet with .610 lift and 260/266 @ .050 duration,105 installed centerline. M-1 intake,and 850 Holley DP. Headers are 2" TTI's, 3.5 collectors. Any estimates??? Thanks in advance! RandyB
|
|
|
Re: YET ANOTHER HOW MUCH DOES IT MAKE QUESTION!!!
[Re: Labratt]
#704881
05/22/10 11:42 AM
05/22/10 11:42 AM
|
Joined: Jul 2005
Posts: 8,647 ELYRIA,OH
blownzoom440
|
Joined: Jul 2005
Posts: 8,647
ELYRIA,OH
|
from wallace calc. Your HP computed from your vehicle ET is 473.53 rear wheel HP and 526.14 flywheel HP. Your HP computed from your vehicle MPH is 465.79 rear wheel HP and 517.55 flywheel HP. have fun at the tuner.i hope it goes well.
|
|
|
Re: YET ANOTHER HOW MUCH DOES IT MAKE QUESTION!!!
[Re: blownzoom440]
#704884
05/22/10 01:06 PM
05/22/10 01:06 PM
|
Joined: Jan 2003
Posts: 10,766 Central Valley, CA.
Quicksilver440
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 10,766
Central Valley, CA.
|
Quote:
from wallace calc. Your HP computed from your vehicle ET is 473.53 rear wheel HP and 526.14 flywheel HP. Your HP computed from your vehicle MPH is 465.79 rear wheel HP and 517.55 flywheel HP.
have fun at the tuner.i hope it goes well.
comparing what I've seen on the dyno....those numbers are right on what I would expect on realistic dyno.
|
|
|
Re: YET ANOTHER HOW MUCH DOES IT MAKE QUESTION!!!
[Re: Labratt]
#704898
05/23/10 07:48 AM
05/23/10 07:48 AM
|
Joined: Jun 2005
Posts: 793 Utah
topbrent
super stock
|
super stock
Joined: Jun 2005
Posts: 793
Utah
|
Quote:
Anybody know where I can pick up 2 mph?
CNC porting by Jeff @ Modern Cylinder Head. - Send him your intake, also.
|
|
|
Re: YET ANOTHER HOW MUCH DOES IT MAKE QUESTION!!!
[Re: topbrent]
#704899
05/23/10 08:24 AM
05/23/10 08:24 AM
|
Joined: Jan 2010
Posts: 184 Bad Axe,MI
EDDIEB
member
|
member
Joined: Jan 2010
Posts: 184
Bad Axe,MI
|
HI Randy,I had my 69 roadrunner there last year great guys,I have a 471 with a six pac cnc eddy's by Jeff and 590ish bullet cam with 260 ish dur@50 and I made 460 at rear wheels. My best run last year was 11.09 @123 with a 1.58 60 ft. I switched to a 4 barrl this year hoping to use the head work with a single plane intake and 1000 pro systems carb,but haven't made it to the track yet. Let us know how it goes EDDIE B
|
|
|
Re: YET ANOTHER HOW MUCH DOES IT MAKE QUESTION!!!
[Re: Labratt]
#704903
05/23/10 05:42 PM
05/23/10 05:42 PM
|
Joined: Jun 2005
Posts: 793 Utah
topbrent
super stock
|
super stock
Joined: Jun 2005
Posts: 793
Utah
|
Quote:
How much flow does the CNC work show @ .600-.650 lift? How does that translate in horsepower gain? ...With a little suspension work,sounds like a high-10-second ride!
Here is the flow sheet from a set of standard port window MCH CNC Edelbrock RPM heads we purchased.
|
|
|
Re: YET ANOTHER HOW MUCH DOES IT MAKE QUESTION!!!
[Re: Labratt]
#704904
05/23/10 05:44 PM
05/23/10 05:44 PM
|
Joined: Jun 2009
Posts: 705 Michigan
Hemiroid
super stock
|
super stock
Joined: Jun 2009
Posts: 705
Michigan
|
Quote:
How much flow does the CNC work show @ .600-.650 lift? How does that translate in horsepower gain?
It really will depend on how extensively ported the heads are now. If Dwayne spent a lot of time with them hand porting them, I doubt Jeff's CNC program will improve it much, if any at all. That's not a shot at Jeff's program in any way, it's just that Dwayne is a very accomplished wedge head porter and there's only so much that can be done. If the heads are just touched up, then there could be significant gains @.600-.700 lift.
|
|
|
Re: YET ANOTHER HOW MUCH DOES IT MAKE QUESTION!!!
[Re: Labratt]
#704905
05/23/10 06:06 PM
05/23/10 06:06 PM
|
Joined: Jun 2005
Posts: 793 Utah
topbrent
super stock
|
super stock
Joined: Jun 2005
Posts: 793
Utah
|
Quote:
GTX weighs 3740,race weight,and runs 11.19-11.30 @ 120mph. Motor's a '70' +.040 440 block,10:25:1 Diamond Forged pistons,OTB Eddy Performers,Comp SQ solid flat tappet with .610 lift and 260/266 @ .050 duration,105 installed centerline. M-1 intake,and 850 Holley DP. Headers are 2" TTI's, 3.5 collectors. Any estimates??? -RandyB
Randy,
In the Fall 2007 Engine Masters Magazine, Steve Dulcich dyno'ed a simple 448" motor back to back with stock RPM heads vs Modern Cylinder Head CNC RPM heads.
At 6000-rpm peak, he gained 46 HP with the swap. From 529hp to 574hp His combo: - Speed-Pro-2355 pistons, 10.2 compression - Comp MM Flat tappet cam, 243°/247° @.050, .586/.597 lift, 110°LSA, 106° installed - Comp 1.6 Roller rockers - Victor intake - RS1000 Demon carb - TTI 2-2_1/8 headers.
|
|
|
Re: YET ANOTHER HOW MUCH DOES IT MAKE QUESTION!!!
[Re: topbrent]
#704906
05/23/10 07:33 PM
05/23/10 07:33 PM
|
Joined: Jun 2009
Posts: 705 Michigan
Hemiroid
super stock
|
super stock
Joined: Jun 2009
Posts: 705
Michigan
|
Quote:
Quote:
GTX weighs 3740,race weight,and runs 11.19-11.30 @ 120mph. Motor's a '70' +.040 440 block,10:25:1 Diamond Forged pistons,OTB Eddy Performers,Comp SQ solid flat tappet with .610 lift and 260/266 @ .050 duration,105 installed centerline. M-1 intake,and 850 Holley DP. Headers are 2" TTI's, 3.5 collectors. Any estimates??? -RandyB
Randy,
In the Fall 2007 Engine Masters Magazine, Steve Dulcich dyno'ed a simple 448" motor back to back with stock RPM heads vs Modern Cylinder Head CNC RPM heads.
At 6000-rpm peak, he gained 46 HP with the swap. From 529hp to 574hp His combo: - Speed-Pro-2355 pistons, 10.2 compression - Comp MM Flat tappet cam, 243°/247° @.050, .586/.597 lift, 110°LSA, 106° installed - Comp 1.6 Roller rockers - Victor intake - RS1000 Demon carb - TTI 2-2_1/8 headers.
I guess I missed the "OOTB" comment the first time I read it. As Topbrent mentioned, there's lots to be gained from Jeff's CNC porting over the OOTB heads.
|
|
|
Re: YET ANOTHER HOW MUCH DOES IT MAKE QUESTION!!!
[Re: Labratt]
#704908
05/24/10 11:30 AM
05/24/10 11:30 AM
|
Joined: Jan 2003
Posts: 17,800 S.E. Michigan
ZIPPY
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 17,800
S.E. Michigan
|
Good luck over there at Jake's Randy.
I've been at 3 different chassis dyno facilities in the area so far, and Jakes is the best to date.
It should be good to compare notes too...although it's been several years since I've been, I still have the paperwork.
Rich H.
Esse Quam Videri
|
|
|
Re: YET ANOTHER HOW MUCH DOES IT MAKE QUESTION!!!
[Re: Dartin]
#704913
05/24/10 08:22 PM
05/24/10 08:22 PM
|
Joined: Jun 2003
Posts: 52,972 Romeo MI
MR_P_BODY
Master
|
Master
Joined: Jun 2003
Posts: 52,972
Romeo MI
|
Quote:
Randy, good luck at Jakes. From the pics I've seen that car is a beauty. Let us know how it all works out. I really need to get the Dart Sport scaled and they are real close. I could even drive it there! If you are still down that way after 3pm give me a shout, I'd like to meet you and the "X"!
Randy J.
I use to live 2 blocks from Jakes... over on the Clinton River(Rivervista dr)
|
|
|
Re: YET ANOTHER HOW MUCH DOES IT MAKE QUESTION!!!
[Re: Labratt]
#704916
05/25/10 09:47 AM
05/25/10 09:47 AM
|
Joined: Jan 2003
Posts: 17,800 S.E. Michigan
ZIPPY
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 17,800
S.E. Michigan
|
Randy, No problem posting some numbers. To understand where they're coming from: At the time it ran the 11.24 in my signature, it was making 488rwhp on a "dynapack 3000" chassis dyno, which bolts to the axle flanges instead of being on tire rollers....a very weird looking setup. Changed carb, intake, headers, exhaust....and was ready for another test but the dynapack guy told me not to come back again (he mainly works with import tuner cars with stick shifts, and he didn't like the torque the high stall converter/big ci combo put into his dyno.....There was a flashing red light on the display that said the torque capacity was at the limit)....So I went to Jakes Dynojet instead where it made 499 rwhp. Never made it back to the track after that. But maybe this weekend it'll finally happen.
Rich H.
Esse Quam Videri
|
|
|
|
|