Re: {{{{{{{{ OIL LEAK @ DIZZY }}}}}}}}}
[Re: rickstershemi]
#678378
04/23/10 05:19 PM
04/23/10 05:19 PM
|
Joined: Jul 2004
Posts: 19,317 State of confusion
Thumperdart
I Live Here
|
I Live Here
Joined: Jul 2004
Posts: 19,317
State of confusion
|
I`ve never had luck w/just the o-ring so I use the paper gasket around the base also......problem solved.
72 Dart 470 n/a BB stroker street car `THUMPER`...Check me out on FB Dominic Thumper for videos and lots of carb pics......760-900-3895.....
|
|
|
Re: {{{{{{{{ OIL LEAK @ DIZZY }}}}}}}}}
[Re: Thumperdart]
#678379
04/23/10 05:33 PM
04/23/10 05:33 PM
|
Joined: Jul 2006
Posts: 9,366 Lehigh Acres, Florida
rickstershemi
OP
master
|
OP
master
Joined: Jul 2006
Posts: 9,366
Lehigh Acres, Florida
|
Quote:
I`ve never had luck w/just the o-ring so I use the paper gasket around the base also......problem solved.
Same thing I thought, just wasn't sure as the oil pressure being 50-75# seems unusual for a stock melling pump on a stock 360 long=block rebuild..???? Will have to grab some gaskets tomorrow and try-em out...
Rickster
|
|
|
Re: {{{{{{{{ OIL LEAK @ DIZZY }}}}}}}}}
[Re: go green]
#678382
04/23/10 05:49 PM
04/23/10 05:49 PM
|
Joined: Jul 2006
Posts: 9,366 Lehigh Acres, Florida
rickstershemi
OP
master
|
OP
master
Joined: Jul 2006
Posts: 9,366
Lehigh Acres, Florida
|
Quote:
If it pukes out under load I would put a bigger PVC vent on it .
Excellent question....drivers side v/c is vented...pass v/c had a PVC, I removed the PVC since the d/s cover was vented....???? Would I be better off blocking off the vent and just running the PVC...??????
Rickster
|
|
|
Re: {{{{{{{{ OIL LEAK @ DIZZY }}}}}}}}}
[Re: rickstershemi]
#678383
04/23/10 05:55 PM
04/23/10 05:55 PM
|
Joined: Jul 2004
Posts: 19,317 State of confusion
Thumperdart
I Live Here
|
I Live Here
Joined: Jul 2004
Posts: 19,317
State of confusion
|
For the pcv to properly work you need the valve on one side and breather on the other. It STILL shouldnt leak when you put the paper gasket on in my opinion.
72 Dart 470 n/a BB stroker street car `THUMPER`...Check me out on FB Dominic Thumper for videos and lots of carb pics......760-900-3895.....
|
|
|
Re: {{{{{{{{ OIL LEAK @ DIZZY }}}}}}}}}
[Re: rickstershemi]
#678385
04/23/10 06:03 PM
04/23/10 06:03 PM
|
Joined: Jun 2003
Posts: 52,972 Romeo MI
MR_P_BODY
Master
|
Master
Joined: Jun 2003
Posts: 52,972
Romeo MI
|
Rick the oil pressure doesnt have anything to do with it, its just splash oil getting up there and getting out... gotta have a O-ring or gasket... if its not vented good enough that pressure is going to get out WHERE EVER it can and right now you dont have a positive seal at that point... get a gasket on it and check the venting
|
|
|
Re: {{{{{{{{ OIL LEAK @ DIZZY }}}}}}}}}
[Re: MR_P_BODY]
#678386
04/23/10 06:38 PM
04/23/10 06:38 PM
|
Joined: Jul 2006
Posts: 9,366 Lehigh Acres, Florida
rickstershemi
OP
master
|
OP
master
Joined: Jul 2006
Posts: 9,366
Lehigh Acres, Florida
|
Quote:
Rick the oil pressure doesnt have anything to do with it, its just splash oil getting up there and getting out... gotta have a O-ring or gasket... if its not vented good enough that pressure is going to get out WHERE EVER it can and right now you dont have a positive seal at that point... get a gasket on it and check the venting
Thanks Mike, kinda what I thought, it has a vent on the d/s and a PVC on the p/s and it was still leaking....so it must be the gasket, the o-ring on the dizzy is suspect as to location, it looked to be below the btm of the casting or very close
I will get a couple of gaskets and try that, should do the trick.... Wasn't sure on the oil pressure playing a part in it though, thanks for clearing that up
Rickster
|
|
|
Re: {{{{{{{{ OIL LEAK @ DIZZY }}}}}}}}}
[Re: rickstershemi]
#678387
04/24/10 12:26 AM
04/24/10 12:26 AM
|
Joined: Jan 2003
Posts: 19,363 Las Vegas
Al_Alguire
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 19,363
Las Vegas
|
Yo sure it is the distributor and not the intake or oil pressure sending unit, or gauge adapter?
"I am not ashamed to confess I am ignorant of what I do not know."
"It's never wrong to do the right thing"
|
|
|
Re: {{{{{{{{ OIL LEAK @ DIZZY }}}}}}}}}
[Re: Al_Alguire]
#678389
04/24/10 06:47 AM
04/24/10 06:47 AM
|
Joined: Jul 2006
Posts: 9,366 Lehigh Acres, Florida
rickstershemi
OP
master
|
OP
master
Joined: Jul 2006
Posts: 9,366
Lehigh Acres, Florida
|
Quote:
Yo sure it is the distributor and not the intake or oil pressure sending unit, or gauge adapter?
I'm fairly certain it is at the dizzy, I know it's not at the sending unit and hope it's not the intake If it still leaks after adding gaskets then it will be the intake
Rickster
|
|
|
Re: {{{{{{{{ OIL LEAK @ DIZZY }}}}}}}}}
[Re: 727builder]
#678392
04/24/10 02:13 PM
04/24/10 02:13 PM
|
Joined: Jul 2006
Posts: 9,366 Lehigh Acres, Florida
rickstershemi
OP
master
|
OP
master
Joined: Jul 2006
Posts: 9,366
Lehigh Acres, Florida
|
Quote:
I was thinking rear intake gasket as well. May have lost its seal when you wasnt running the pcv valve.
It was leaking before I disconnected the pvc...???? It looks to be coming from the dizzy, going to pull it today or tomorrow and try the gaskets on the dizzy...?????
Rickster
|
|
|
Re: {{{{{{{{ OIL LEAK @ DIZZY }}}}}}}}} FIXED }}}}}}}}
[Re: Thumperdart]
#678394
04/24/10 05:26 PM
04/24/10 05:26 PM
|
Joined: Jul 2006
Posts: 9,366 Lehigh Acres, Florida
rickstershemi
OP
master
|
OP
master
Joined: Jul 2006
Posts: 9,366
Lehigh Acres, Florida
|
Quote:
I guarantee you IF it`s the dizzy, that gasket will seal it......................been there done that.
Well it looks like your the winner Dominic....it was the dizzy and I had a gasket for it in the kit that came with the long block never thought to use it do to the o-ring on the cheapo billet dizzy By the way I am very pleased with this distributor....$59 bucks delivered and so far it's a fairly nice piece
|
|
|
Re: {{{{{{{{ OIL LEAK @ DIZZY }}}}}}}}} FIXED }}}}}}}}
[Re: rickstershemi]
#678395
04/24/10 05:35 PM
04/24/10 05:35 PM
|
Joined: Jun 2003
Posts: 52,972 Romeo MI
MR_P_BODY
Master
|
Master
Joined: Jun 2003
Posts: 52,972
Romeo MI
|
Quote:
Quote:
I guarantee you IF it`s the dizzy, that gasket will seal it......................been there done that.
Well it looks like your the winner Dominic....it was the dizzy and I had a gasket for it in the kit that came with the long block never thought to use it do to the o-ring on the cheapo billet dizzy By the way I am very pleased with this distributor....$59 bucks delivered and so far it's a fairly nice piece
Glad to hear you got that out of the way
|
|
|
|
|