Previous Thread
Next Thread
Print Thread
Page 1 of 2 1 2
How to get trans to shift at a higher rpm? #460985
09/06/09 07:55 PM
09/06/09 07:55 PM
Joined: Sep 2004
Posts: 6,906
IL, Aurora
A
ademon Offline OP
master
ademon  Offline OP
master
A

Joined: Sep 2004
Posts: 6,906
IL, Aurora
got a sb with 1971 727, trans go shift kit, bolt in sprag. 9.5" converter ect.. ect.. when in drive it shifts from 1 to 2nd at about 15 and to 3rd at 20 with normal throttle. when floored it shifts at about 4,800. carb is a holley with the right bracket and downshift linkage, at full throttle the linkage has the trans line psi bracket all the way back. any ideas?

Re: How to get trans to shift at a higher rpm? [Re: ademon] #460986
09/06/09 08:01 PM
09/06/09 08:01 PM
Joined: Jan 2003
Posts: 20,348
Eagle, Idaho
Neil Offline
The Doctor is in.
Neil  Offline
The Doctor is in.

Joined: Jan 2003
Posts: 20,348
Eagle, Idaho
The tailshaft governor weight and springs are what controls the wot shift points IIRC.

Not sure how you raise the parts throttle shift points. Probably somewhere in the valve body?????

Re: How to get trans to shift at a higher rpm? [Re: ademon] #460987
09/06/09 08:02 PM
09/06/09 08:02 PM
Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
1_WILD_RT Offline
Management Trainee
1_WILD_RT  Offline
Management Trainee

Joined: Jan 2004
Posts: 27,347
Today? Who Knows?

Re: How to get trans to shift at a higher rpm? [Re: 1_WILD_RT] #460988
09/06/09 08:21 PM
09/06/09 08:21 PM
Joined: Sep 2004
Posts: 6,906
IL, Aurora
A
ademon Offline OP
master
ademon  Offline OP
master
A

Joined: Sep 2004
Posts: 6,906
IL, Aurora
Quote:

http://www.aandatrans.com/Departments/Chrysler-727-Trans/Governor-Kits.aspx


I've seen those before, what i don't get is didn't the trans in stock form shift in the mid 5k range? its the original 340 trans.

Re: How to get trans to shift at a higher rpm? [Re: ademon] #460989
09/06/09 08:37 PM
09/06/09 08:37 PM
Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
1_WILD_RT Offline
Management Trainee
1_WILD_RT  Offline
Management Trainee

Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
You'd have to check the factory service manual for a spec but most shift around 45-4800 @ WOT.. Increasing the length of the "kickdown" linkage (throttle valve pressure linkage) can have some minimal effect but the max TV pressure is equivalent to line pressure so governor valve weight is the true limiting factor.. TV Pressure can effect 1-2 & 2-3 part throttle shift points..

Re: How to get trans to shift at a higher rpm? [Re: ademon] #460990
09/06/09 08:47 PM
09/06/09 08:47 PM
Joined: Jan 2003
Posts: 1,263
Southwestern Ontario Canada
racealittle Offline
pro stock
racealittle  Offline
pro stock

Joined: Jan 2003
Posts: 1,263
Southwestern Ontario Canada
I'm not an expert on what rpm an original 340 727 trans shifted at in drive, but 4800-5000 rpm is what I would expect out of a good 727 car trans that has a Transgo TF2 kit in it.

I have bought the governor weights to correct the shift point. You have to talk with Rick at A&A about what he thinks is the right governor weight. Choosing the right weight depends on how your trans is built, your tire size, and your choice of gear. Turning up the line pressure in the trans can also raise the shift point.

If Rick specs out the governor weight and it doesn't suit your need, he will exchange it until you hit the shift point you require.


Too many cars, too many parts, too little coin, too little space to work in, too little time left to make it all happen! Update: down to one ride, still too many parts, a little more jingle in the pocket, gaining space, and it's going to happen this year!
Re: How to get trans to shift at a higher rpm? [Re: racealittle] #460991
09/06/09 09:37 PM
09/06/09 09:37 PM
Joined: Jan 2003
Posts: 1,180
Willoughby Hills, Ohio
gd9704 Offline
super gas
gd9704  Offline
super gas

Joined: Jan 2003
Posts: 1,180
Willoughby Hills, Ohio
How involved is changing out the governor?

Re: How to get trans to shift at a higher rpm? [Re: gd9704] #460992
09/06/09 09:56 PM
09/06/09 09:56 PM
Joined: Jan 2004
Posts: 9,066
Eugene, Oregon
M
minivan Offline
master
minivan  Offline
master
M

Joined: Jan 2004
Posts: 9,066
Eugene, Oregon
Quote:

How involved is changing out the governor?




AND will changing the governer weight change the shift RPM at part throttle??

Re: How to get trans to shift at a higher rpm? [Re: minivan] #460993
09/06/09 10:17 PM
09/06/09 10:17 PM
Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
1_WILD_RT Offline
Management Trainee
1_WILD_RT  Offline
Management Trainee

Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
Quote:

Quote:

How involved is changing out the governor?




AND will changing the governor weight change the shift RPM at part throttle??




Jack up car, support the trans, remove driveshaft & trans crossmember & mount, remove speedo gear, remove two Phillips screws holding cover hidden by trans mount.. Remove six bolts holding tailshaft housing.. Spread snap ring tabs behind cover held by two Phillips screws & slide tail housing off trans... Now you'll see the governor... Remove one "E" clip & one snap ring remove old Governor weight replace with new... Reverse process...

Yes a lighter governor weight will effect part throttle because the governor is a centrifugal weight/valve trying to overcome hydraulic pressure...By reducing the weight it needs to spin faster to overcome the same hydraulic force....

Re: How to get trans to shift at a higher rpm? [Re: ademon] #460994
09/06/09 10:19 PM
09/06/09 10:19 PM
Joined: Feb 2005
Posts: 4,309
Prospect, PA
BSB67 Offline
master
BSB67  Offline
master

Joined: Feb 2005
Posts: 4,309
Prospect, PA
If you have your line pressure where you like it, you'll need to change the govenor to move the wot shift point. If you're trying to get to 6000 rpm or less, you can probably get there by reducing the weight of the inner weight. If you're looking for something higher, you'll likely need to change the spring as well.

What rpm does wot 2-3 shift happen? If 2-3 shifts at a lower rpm than 1-2, then adjust the governor to the desired 2-3 wot shift point, then change the 1-2 shift valve spring to get the 1-2 to the desired rpm.

Re: How to get trans to shift at a higher rpm? [Re: BSB67] #460995
09/06/09 10:51 PM
09/06/09 10:51 PM
Joined: Jan 2003
Posts: 5,442
Indiana
Y
YO7_A66 Offline
master
YO7_A66  Offline
master
Y

Joined: Jan 2003
Posts: 5,442
Indiana
Changing the gov will change the light throttle shift rpm too. Rick will need to ask you a few questions about your setup before he will suggest a gov kit. Also, ask Rick about the Split-Shift spring kit becuase you will most likely need it once you have the new gov in. This kit contains some springs that you will need to swap out in yoour VB. If you installed your TF-2 kit, then you can EASILY swap one of these springs out in the 1-2 shift piston to tune the WOT shift differences between the 1-2 WOT and the 2-3 WOT shifts. In other words, once you add the new gov and your goal is to get both the 1-2 and the 2-3 WOT shift points to the same rpm. If the new gov makes a large difference in shift points (lets say 5400/5800rpms), then the kit will have a spring (with instructions) that may allow the shift points to become closer (maybe 5600/5800rpms).
I have used two of the A-A gov's and each time I wanted to get both WOT shifts within a 100rpm difference, I had to use the A-A Split-Shift spring kit to get me close (if I remember right, both times I was within 200rpms). Then to get my shift points even closer (I was beening anal about it), I bought some springs from a spring manufacturer once I measured a couple of the 1-2 shift springs. Then after some testing I was able to get both my shifts points to the same rpm. You can also use the line pressure to gain/lose shift rpms too.


I am a huge fan of tuning the shift points in an auto car. The valve body can be fine tuned just like the carb and the ignition of a car.


1970 YO7 A66 [Canadian Export] F8 Challenger
340 (Currently in shop for stroker assy.)
Re: How to get trans to shift at a higher rpm? [Re: gd9704] #460996
09/07/09 04:36 PM
09/07/09 04:36 PM
Joined: Jan 2003
Posts: 25,618
Rio Linda, CA
John_Kunkel Offline
Too Many Posts
John_Kunkel  Offline
Too Many Posts

Joined: Jan 2003
Posts: 25,618
Rio Linda, CA
Quote:

How involved is changing out the governor?




A lot more involved than just shifting manually at the desired RPM.


The INTERNET, the MISinformation superhighway
Re: How to get trans to shift at a higher rpm? [Re: John_Kunkel] #460997
09/07/09 04:44 PM
09/07/09 04:44 PM
Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
1_WILD_RT Offline
Management Trainee
1_WILD_RT  Offline
Management Trainee

Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
Quote:

Quote:

How involved is changing out the governor?




A lot more involved than just shifting manually at the desired RPM.




True...

Re: How to get trans to shift at a higher rpm? [Re: John_Kunkel] #460998
09/08/09 10:34 AM
09/08/09 10:34 AM
Joined: Dec 2007
Posts: 387
n/w, PA
D
demonH1B Offline
enthusiast
demonH1B  Offline
enthusiast
D

Joined: Dec 2007
Posts: 387
n/w, PA
I too vote to shift manually at wot.

Re: How to get trans to shift at a higher rpm? [Re: demonH1B] #460999
09/08/09 10:46 AM
09/08/09 10:46 AM
Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
1_WILD_RT Offline
Management Trainee
1_WILD_RT  Offline
Management Trainee

Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
Quote:

I too vote to shift manually at wot.




I don't vote for manually shifting at WOT & likely neight does Mr Kunkle... The statement is about how difficult it is to install a governor vs manually shifting... Manually selecting 1st geat applies the low/reverse band.. Thats a good thing when launching the car, especially if you have some serious HP but at the point the 1-2 shift occurs the band must release or there will be a shift overlap (Two gears applied at the same time) Torqueflights are prone to shift overlap without applying manual low why add to the difficulty..

Re: How to get trans to shift at a higher rpm? [Re: 1_WILD_RT] #461000
09/08/09 03:57 PM
09/08/09 03:57 PM
Joined: Jan 2003
Posts: 25,618
Rio Linda, CA
John_Kunkel Offline
Too Many Posts
John_Kunkel  Offline
Too Many Posts

Joined: Jan 2003
Posts: 25,618
Rio Linda, CA
Quote:



I don't vote for manually shifting at WOT & likely neight does Mr Kunkle...




Wrong, I DO advocate manual shifting at WOT as opposed to letting the governor have control.


Quote:

Torqueflights are prone to shift overlap without applying manual low why add to the difficulty.




To take some of the load off the sprag, the overlap can be greatly reduced with proper mods.


The INTERNET, the MISinformation superhighway
Re: How to get trans to shift at a higher rpm? [Re: John_Kunkel] #461001
09/08/09 06:03 PM
09/08/09 06:03 PM
Joined: Jan 2003
Posts: 4,587
St. John's Newfoundland
440newport Offline
master
440newport  Offline
master

Joined: Jan 2003
Posts: 4,587
St. John's Newfoundland
not to hijack but on a related note, my car shifts early on the 1-2 but the 2-3 shift is just about perfect IMO. I have 3.91 gears and unless I'm really into the pedal the 1-2 shift happens at about 5mph. The 2-3 shift happens at about say 30mph normal driving and about 75mph at WOT. Can the 1-2 shift be adjusted without effecting 2-3? The throttle pressure linkage seems to be adjusted correctly (bouchillion cable setup)

Re: How to get trans to shift at a higher rpm? [Re: ademon] #461002
09/08/09 06:38 PM
09/08/09 06:38 PM
Joined: May 2005
Posts: 2,295
dark side of the moon
D
Dougsmopars Offline
top fuel
Dougsmopars  Offline
top fuel
D

Joined: May 2005
Posts: 2,295
dark side of the moon
Check your kick down linkage. There is a small hole in throttle bracket and pivot. Insert a drill bit through those holes. Un snap the lower rod. adjust the lower rod so in it's natural state it will snap back on. Then remove the drill bit. Hold throttle wide open. Adjust upper rod so that at WOT there is only a bit of free play on trans lever. You don't want the lever pressed back hard. It needs a little free play. Many people forget to adjust the lower rod correctly to get the proper ratio.

Re: How to get trans to shift at a higher rpm? [Re: 440newport] #461003
09/08/09 08:07 PM
09/08/09 08:07 PM
Joined: Jan 2003
Posts: 25,618
Rio Linda, CA
John_Kunkel Offline
Too Many Posts
John_Kunkel  Offline
Too Many Posts

Joined: Jan 2003
Posts: 25,618
Rio Linda, CA
Quote:

Can the 1-2 shift be adjusted without effecting 2-3?




Yes, a stiffer return spring in the 1-2 shift valve bore can will raise the 1-2 shift speed but it's not really worth the effort. The 3.91 gears make the trans think you're going faster than the actual road speed.


The INTERNET, the MISinformation superhighway
Re: How to get trans to shift at a higher rpm? [Re: John_Kunkel] #461004
09/08/09 08:41 PM
09/08/09 08:41 PM
Joined: Jan 2003
Posts: 1,180
Willoughby Hills, Ohio
gd9704 Offline
super gas
gd9704  Offline
super gas

Joined: Jan 2003
Posts: 1,180
Willoughby Hills, Ohio
Quote:

Quote:

How involved is changing out the governor?




A lot more involved than just shifting manually at the desired RPM.





Love that.

I guess I'll wait until I HAVE to take the trans out before messing with the governor.

Page 1 of 2 1 2






Powered by UBB.threads™ PHP Forum Software 7.7.1