I'm looking for the following parts.

Bench seat seatback release latch, knob & hardware for a 1973 A-body bench seat. I just need the driver side but will buy both sides if necessary. My passenger side latch is shown in the pic below.

Black seat hinge covers for a 73 bench seat.

1969 Barracuda black sport steering wheel. This is the black version of the optional woodgrain sport wheel.

Complete set of column to trans. shift linkage for a 340 A-body and 727 trans.

Factory big block A-body throttle cable.

A nice pair of black sunvisors for a 1970 Dart. I believe 69's are the same but not sure about other years.

gt340 at yahoo.com

Looking for a 67-69 Dart or Barracuda (preferred ) or possibly a 70-72 Duster or Dart, nothing special, looking for something to build into a race car, please no finished cars, total rust buckets or bad wrecks, don’t care about driveline or interior, just needs to be able to roll onto a trailer. Prefer it to be in the Texas, Oklahoma, Louisiana area, other areas considered if the owner is willing to meet me in the middle somewhere, thanks, pm me here or email me with pics and price at alilblacktruck@gmail.com, thanks

*******************WANTED ************ 1968-1969 barracuda fastback maroon interior parts like dash pad-ex .......please let me know what you have...................PM here........Frank......................thanks !

I want a dodge dart to fix up with my kids. I prefer a 67-69 but will consider others as my budget is pretty limited. I got $2000 in cash and I could throw in a nice 99 Durango with 318, a nice 95 Dakota with a 5.9 magnum swap rebuilt auto trans 3.92 limited slip 9.25 4wd ex cab short tube headers... or even I have a solid 75 duster with 8.25 318 auto and disc brakes I could throw in if I don't need any major parts off it for the dart. I will even consider a 4 door but I don't want rust if its a 4 door. Engine don't matter as we are wanting to do a hemi swap anyhow so I'm not paying premium price because it was a BB or 340 car or anything like that.

I would even consider buying just a hood, bumper and grille for a 67-69 dart that I can put on my duster and maybe even a dash so I can build a fastback Dart-ster....?


I am in western Montana and it needs to be within a few hundred miles unless you are willing to deliver it. I have a trailer with a winch so it don't have to run or even have a drivetrain but should otherwise be mostly complete.


I know it's like looking for a needle in a haystack but I got to try


406 260 8596 is my cell you can test me pics and info.

I also have a ton of gen III hemi parts I could throw some in... BGE heads, blocks, cranks, 5.7 blocks, cranks, early and later 5. heads, intakes...

Looking for a clean A Body. Budget in the mid 20k’s. I’m in Nj but would travel. Targeting 8 cylinders only.

I am looking for the trim piece that fits over the radio/HVAC controls on a 1971 Dodge Dart Swinger with Air Conditioning. Attached is a photo of what it would look like. It has a top row of push button HVAC controls. Driver quality condition is fine.

Thank you,

Greg

WTB - 1968 Dodge Dart Coupe for ground up build drag project.

Not interested in any completed cars, just need a shell with front suspension to get started. Doesn't need to have front fenders, hood, seats, or any windows.

PM me here what you have, where you're located, and a price.

Thanks

My wagon project is about to be done .

I could use a few pieces to finish up some details , if you know of one in a salvage yard near you ?

There is a piece of plastic that covers up inside next to back one each side and a piece of plastic that covers the roofline post on inside next to side glass , these are really flimsy .. I have a couple , they are not very nice

and I would like rubber plugs that so in area right below side glass , the oval ones I think are same as firewall plugs
one is kind of a tri- oval, those might be tuff to locate

I'm looking for a complete set of wheel lip moldings for a 69 Dart. Must be in nice condition with no dents or corrosion and good screw holes please. Originals only as I cannot afford NOS and I don't really want reproduction moldings.

gt340 at yahoo.com

WTB 67-75 bucket seat tracks.
Just need to function. Re-pros are fine. PM me please. Found!

Need one for a friend over seas ..... also rt fender trim.
I'll pay what it takes because I owe the guy for helping me buy the last set of torsion bar bushings on the planet for my FMJ project.
The ad was in Japanese...... you get it.
Thanks ,
John
And thanks for the ad !!

WANTED BY BILL ROLIK:


Looking for ORIGINAL, UN-MODIFIED, NEVER REBUILT 10-3/4" TORQUE CONVERTER for the following applications:


68 340-383 4 barrel

69 340-383 4 barrel

70 340-383 4 barrel

71 340-383 4 barrel

72 340 forged crank only

73-75 440 HP only


Will be at Chrysler Carlisle in my usual vendor spaces C18-24, near Gate 2.


Thanks,

Bill Rolik

bremotorsports@verizon.net

201-394-5533 Cell/Text

WANTED; I have a friend wanting a new or re-manufactured one barrel carburetor for his 1974 Dodge Dart with a 226 six cylinder.

Mansfield Pa

I need one good 10" finned front brake drum with good hub and bearings, small bolt pattern, with right hand studs for a 70 Duster. I can pick up at Chrysler Carlisle Nationals. Thank you!