Looking For Mr. Six Pack Cam Information - Moparts Forums

Register Log In Moparts Forums Moparts Restoration & A12 Forum Looking For Mr. Six Pack Cam Information

Print Thread

Page 8 of 8

1

2

3

4

5

6

7

8

Re: Looking For Mr. Six Pack Cam Information [Re: AdamR] #32658 07/02/12 11:48 AM 07/02/12 11:48 AM
Joined: Jan 2003 Posts: 1,551 Marion,Indiana S Seth_Jones pro stock
Seth_Jones pro stock S Joined: Jan 2003 Posts: 1,551 Marion,Indiana	The only thing not stock is the 2 1/2 TTI exhaust pipes and Dynomax mufflers.Tailpipes are muffler shop bent 2 1/4.My calculated compression was 8.84:1 but I could go up to 9.9:1 by the rules.My pistons were .045 in the hole with a .028 MP head gasket and a 70cc chamber on the 587 heads.Block was bored .030 and stress honed but not decked.Rotating assembly was balanced.I'm running 3.55's and had a 1.99 60 ft on Saturday morning.Hot lapped it and had a 2.01 just a few minutes later.

Re: Looking For Mr. Six Pack Cam Information [Re: Seth_Jones] #32659 07/04/12 06:02 PM 07/04/12 06:02 PM
Joined: Nov 2003 Posts: 5,160 Texas dannysbee master
dannysbee master Joined: Nov 2003 Posts: 5,160 Texas	Some work on those 60' times and you will be well into the 13's. Getting old just means you were smarter than some and luckier than others.

Re: Looking For Mr. Six Pack Cam Information [Re: dannysbee] #2761553 04/08/20 03:09 PM 04/08/20 03:09 PM
Joined: Sep 2006 Posts: 1,155 Home of the Bluegrass MoparJunkie super stock
MoparJunkie super stock Joined: Sep 2006 Posts: 1,155 Home of the Bluegrass	Guys, I'm bumping this thread cause I wanna run one of Mr. Sixpack's cams..... Are these still available? "It takes a Mopar to catch a Mopar” 1970 Challenger T/A 4 speed EV2

Re: Looking For Mr. Six Pack Cam Information [Re: MoparJunkie] #2761567 04/08/20 03:41 PM 04/08/20 03:41 PM
Joined: Jan 2003 Posts: 3,687 South San Francisco, Ca 70sixpkrt master
70sixpkrt master Joined: Jan 2003 Posts: 3,687 South San Francisco, Ca	A buddy of mine bought one of his cams last year and it went flat. He followed all of the proper break in procedures. I believe his cams are Engle Cams. [img]http://www.imgur.com/hxlGUJt.gif[/img] 4-speed 3:54 Dana 13.01 @107.93 with street tires (not hooking up)

Re: Looking For Mr. Six Pack Cam Information [Re: MoparJunkie] #2761666 04/08/20 06:29 PM 04/08/20 06:29 PM
Joined: Aug 2005 Posts: 302 Hinckley, Ohio KWF340 enthusiast
KWF340 enthusiast Joined: Aug 2005 Posts: 302 Hinckley, Ohio	Originally Posted by HemiA12Bee Guys, I'm bumping this thread cause I wanna run one of Mr. Sixpack's cams..... Are these still available? I bought one several months ago so yes they are still available. 1968 Charger R/T, 440, Auto, GG1; 1969 Super Bee, 383, 4-speed, T5; 1969.5 Road Runner, 440-6, 4-speed, 96; 1970 Duster 340, 4-speed, EV2; 1970 Charger R/T SE, 440 (496), Auto, EB3; 1970 Dart Swinger 340 (416), 4-speed, EV2; 1966 Corvette convertible, L79, 4-speed, Red 1970 Corvette coupe, LS5, 4-speed, Daytona yellow; 2000 Corvette coupe, LS1, 6-speed, Twin Turbo, Torch red.

Re: Looking For Mr. Six Pack Cam Information [Re: KWF340] #2761757 04/08/20 10:03 PM 04/08/20 10:03 PM
Joined: Sep 2006 Posts: 1,155 Home of the Bluegrass MoparJunkie super stock
MoparJunkie super stock Joined: Sep 2006 Posts: 1,155 Home of the Bluegrass	I talked to Bob today. Thanks "It takes a Mopar to catch a Mopar” 1970 Challenger T/A 4 speed EV2

Re: Looking For Mr. Six Pack Cam Information [Re: MoparJunkie] #2762715 04/11/20 01:20 PM 04/11/20 01:20 PM
Joined: Jan 2003 Posts: 3,103 Phila Pa S scatpacktom master
scatpacktom master S Joined: Jan 2003 Posts: 3,103 Phila Pa	This thread contains a lot of good old fun in it!

Re: Looking For Mr. Six Pack Cam Information [Re: MoparJunkie] #2762776 04/11/20 04:28 PM 04/11/20 04:28 PM
Joined: Jan 2003 Posts: 338 Montreal Quebec STROKIE enthusiast
STROKIE enthusiast Joined: Jan 2003 Posts: 338 Montreal Quebec	If your 1/4 mile target is in the 12 seconds zone, Mr. Six Pack Cam is your best friend... https://youtu.be/tt-x-_3jjmE

Page 8 of 8

1

2

3

4

5

6

7

8

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1