Previous Thread
Next Thread
Print Thread
Consistency of ARP rod bolt length #3089132
10/25/22 03:01 PM
10/25/22 03:01 PM
Joined: Jan 2003
Posts: 7,471
Minnesota
Hemi_Joel Offline OP
master
Hemi_Joel  Offline OP
master

Joined: Jan 2003
Posts: 7,471
Minnesota
https://www.enginelabs.com/news/what-i-learned-today-with-jeff-smith-reverse-rod-bolt-stretch-tech/

This article says you can look up the ARP part number for a rod bolt, get the length, and measure it on an already assembled engine to determine if it has the proper stretch/torque.

I have not found the lengths to be sufficiently consistent. Even on one set of rods they vary enuff that I have reset the length gauge from one bolt to the next.

What have you found for length consistency?


[img]http://i.imgur.com/boeexFms.jpg[/img]
31 Plymouth Coupe, 392 Hemi, T56 magnum
RS23J71
RS27J77
RP23J71
RO23J71
WM21J8A
I don't regret the things I've done. I only regret the things I didn't do.
"Wise men talk because they have something to say; fools because they have to say something. ~ Plato"
Re: Consistency of ARP rod bolt length [Re: Hemi_Joel] #3089133
10/25/22 03:04 PM
10/25/22 03:04 PM
Joined: Aug 2019
Posts: 9,291
Super Spudsville
Mr PotatoHead Offline
Half Baked
Mr PotatoHead  Offline
Half Baked

Joined: Aug 2019
Posts: 9,291
Super Spudsville
I have found this not to be the case on rods that come with ARP bolts. Some are the same, some 2-3-6 thousands off using the same tool in the article.

Possibly a NEW package of un used bolts from ARP might show different. Bit I do not know.

That article does not seem to be correct if they claim all bolts are the same from the start.




Screenshot 2022-10-25 at 13-08-03 ARP Rod Bolt Stretch Gauge How-to - Hot Rod Engine Tech.png

STOP POTATO HATE!
Re: Consistency of ARP rod bolt length [Re: Hemi_Joel] #3089151
10/25/22 05:02 PM
10/25/22 05:02 PM
Joined: Dec 2018
Posts: 88
IL
8
83hurstguy Offline
member
83hurstguy  Offline
member
8

Joined: Dec 2018
Posts: 88
IL
The last two engines with ARP 2000 rod bolts (Molnar rods) had around 0.006 variance, so the gauge was different on nearly every bolt.

I feel like the wording is vague, and don't think Jeff Smith was actually suggesting measuring the bolts without loosening and measuring the change. The way I read the article, you take a baseline measurement, loosen the bolt, recheck the length to calculate change and that will tell you if they were torqued correctly or not. Odds are if 1-2 rod bolts are correct, you don't have to check all 16. I pasted the paragraph below for quick reference. He didn't say look up the length as much as look up the original stretch requirements... I actually challenge that approach from a different angle because ARP typically defers required rod bolt stretch to the rod manufacturers.

This technique can also be used to check the veracity of an engine that you may not know the history of. If the rod bolts are from ARP, you can look up the part number and then search for the online instructions on the ARP website to find the original stretch numbers and compare these numbers to what you see on the actual bolts. You may be surprised at what you find, since many engine builders do not use rod bolt stretch when torquing the rod bolts.

Last edited by 83hurstguy; 10/25/22 05:04 PM.
Re: Consistency of ARP rod bolt length [Re: 83hurstguy] #3089188
10/25/22 08:28 PM
10/25/22 08:28 PM
Joined: Mar 2006
Posts: 9,791
MI, usa
dvw Offline
master
dvw  Offline
master

Joined: Mar 2006
Posts: 9,791
MI, usa
In my experience none of the bolts are close. You need to check them individually.
Doug

Re: Consistency of ARP rod bolt length [Re: dvw] #3089215
10/25/22 10:07 PM
10/25/22 10:07 PM
Joined: Oct 2006
Posts: 1,262
New York, USA
Chargerfan68 Offline
pro stock
Chargerfan68  Offline
pro stock

Joined: Oct 2006
Posts: 1,262
New York, USA
Originally Posted by dvw
In my experience none of the bolts are close. You need to check them individually.
Doug


Exactly my experience as well. Measure individually…..it is definitely important and worth it to do it. Next rebuild, it could prevent a potential bomb.


1.50 60Ft. , 10.75@ 127MPH Hauling 3900 LBS.
Re: Consistency of ARP rod bolt length [Re: Mr PotatoHead] #3089224
10/25/22 10:26 PM
10/25/22 10:26 PM
Joined: Aug 2003
Posts: 43,007
Bend,OR USA
C
Cab_Burge Offline
I Win
Cab_Burge  Offline
I Win
C

Joined: Aug 2003
Posts: 43,007
Bend,OR USA
I've used the stretch method for torquing rod bolts for a lot of years now on ARP and other "quality" bolts. The ARP 8740 bolts and their 2000 and L19 bolts all had some minor length differences in all of them whiney shruggy Say from .0003 to .0050 shock shruggy
Set the dial indicator at zero for each bolt individually and then stretch them, tighten, torque them and remeasure them for the proper lengths wrench scope up twocents


Mr.Cab Racing and winning with Mopars since 1964. (Old F--t, Huh)
Re: Consistency of ARP rod bolt length [Re: Hemi_Joel] #3089421
10/26/22 03:44 PM
10/26/22 03:44 PM
Joined: Jan 2003
Posts: 16,916
NC
440Jim Offline
I Live Here
440Jim  Offline
I Live Here

Joined: Jan 2003
Posts: 16,916
NC
Originally Posted by Hemi_Joel
What have you found for length consistency?
Recent set of rods with ARP bolts.
1.7590
1.7615
1.7550
1.7571
1.7630
1.7605
1.7628
1.7626
1.7588
1.7567
1.7556
1.7594
1.7592
1.7574
1.7630
1.7588


1993 Daytona, 5.50 at 130mph (1/8) 1.19 sixty ft (PG). Link to 572 B1 - Part 1
Re: Consistency of ARP rod bolt length [Re: 440Jim] #3089542
10/27/22 12:11 AM
10/27/22 12:11 AM
Joined: Jan 2003
Posts: 7,471
Minnesota
Hemi_Joel Offline OP
master
Hemi_Joel  Offline OP
master

Joined: Jan 2003
Posts: 7,471
Minnesota
It would be SO nice if they would precision grind the length. Then we could set the gauge once.

I've been using an angle gauge, then check the length. The angle gauge is pain when the motor is already installed.


[img]http://i.imgur.com/boeexFms.jpg[/img]
31 Plymouth Coupe, 392 Hemi, T56 magnum
RS23J71
RS27J77
RP23J71
RO23J71
WM21J8A
I don't regret the things I've done. I only regret the things I didn't do.
"Wise men talk because they have something to say; fools because they have to say something. ~ Plato"
Re: Consistency of ARP rod bolt length [Re: Hemi_Joel] #3089549
10/27/22 01:13 AM
10/27/22 01:13 AM
Joined: Aug 2003
Posts: 43,007
Bend,OR USA
C
Cab_Burge Offline
I Win
Cab_Burge  Offline
I Win
C

Joined: Aug 2003
Posts: 43,007
Bend,OR USA
I try to write down the torque needed for each bolt to get it to stretch to the middle of recommended lengths, IE.0057 to .0062 shoot for .0059 to .0060.
I do this on the bench with the rods in a rod vice, one bolt at a time wrench
If i was smart I would remove all the bolts and measure the free lengths and then match them up in the rods so both bolts are the same length to start with work Instead of doing one at a time starting with no torque and setting the gauge each time on every bolt wrench shruggy
I had one Molnar bolt overstretch at 55 Ft. lbs. to start with, all the rest needed 68 Ft lbs. to get anywhere near close the minimum stretch shock shruggy

Last edited by Cab_Burge; 10/27/22 01:14 AM.

Mr.Cab Racing and winning with Mopars since 1964. (Old F--t, Huh)
Re: Consistency of ARP rod bolt length [Re: Cab_Burge] #3089619
10/27/22 11:49 AM
10/27/22 11:49 AM
Joined: Mar 2018
Posts: 114
NW Indiana
P
powertrip Offline
member
powertrip  Offline
member
P

Joined: Mar 2018
Posts: 114
NW Indiana
Originally Posted by Cab_Burge
I
I had one Molnar bolt overstretch at 55 Ft. lbs. to start with, all the rest needed 68 Ft lbs. to get anywhere near close the minimum stretch shock shruggy


I've had that happen to me more than once, I didn't feel comfortable with using those bolts so I changed them.

Re: Consistency of ARP rod bolt length [Re: Cab_Burge] #3090091
10/29/22 12:25 AM
10/29/22 12:25 AM
Joined: Jan 2003
Posts: 1,753
Windsor, ON, Canada
D
Diplomat360 Offline
top fuel
Diplomat360  Offline
top fuel
D

Joined: Jan 2003
Posts: 1,753
Windsor, ON, Canada
Originally Posted by Cab_Burge
...I had one Molnar bolt overstretch at 55 Ft. lbs. to start with, all the rest needed 68 Ft lbs. to get anywhere near close the minimum stretch shock shruggy


Same here, I record each bolt, before & after, went through 3 "warm-up" cycles before I did the final install.

Having said that, Eagle recommended 75 ft-lbs for 0.0064-0.0068 stretch on my H-beam rods with ARP S2000 bolts...I went up to 85 ft-lbs and that only got me to about 0.0055, take a look at the attachment tracker.

mopar-rod-bolt-stretch.jpg
Re: Consistency of ARP rod bolt length [Re: Diplomat360] #3090207
10/29/22 02:19 PM
10/29/22 02:19 PM
Joined: Sep 2003
Posts: 19,237
north of coder
moparx Offline
"Butt Crack Bob"
moparx  Offline
"Butt Crack Bob"

Joined: Sep 2003
Posts: 19,237
north of coder
so now with .001 [approximately] less than recommended stretch on the bolts, at 10ftlb more torque than recommended, i wonder what that does to the roundness of the rod diameter ?
also, how does the above affect bearing crush and clearance ?
beer

Re: Consistency of ARP rod bolt length [Re: moparx] #3090236
10/29/22 03:41 PM
10/29/22 03:41 PM
Joined: Aug 2003
Posts: 43,007
Bend,OR USA
C
Cab_Burge Offline
I Win
Cab_Burge  Offline
I Win
C

Joined: Aug 2003
Posts: 43,007
Bend,OR USA
Originally Posted by moparx
so now with .001 [approximately] less than recommended stretch on the bolts, at 10ftlb more torque than recommended, i wonder what that does to the roundness of the rod diameter ?
also, how does the above affect bearing crush and clearance ?
beer
As far as the roundness of the rod without the bearing in place and torque down to that tightness you should find out wrench scope grin
Same thing with the bearings in placed and torqued wrench scope I have up
Most aftermarket replacement bearings will have more oil clearance at the sides where the cap and rod meet than if you make the same measurement aligned with the rod bottom and wrist pins scope
I've seen from.0010 to .0018 difference at the bearing mating surfaces, that is designed to store oil and lubricate the crank when the engine is running is what Iwas told years ago at one of the Mopar Drag clinics upwork

Last edited by Cab_Burge; 10/29/22 03:42 PM.

Mr.Cab Racing and winning with Mopars since 1964. (Old F--t, Huh)
Re: Consistency of ARP rod bolt length [Re: Cab_Burge] #3090720
10/31/22 02:20 PM
10/31/22 02:20 PM
Joined: Sep 2003
Posts: 19,237
north of coder
moparx Offline
"Butt Crack Bob"
moparx  Offline
"Butt Crack Bob"

Joined: Sep 2003
Posts: 19,237
north of coder
agreed Cab. up
i was wondering what the OP got for a measurement on the big end. [if he measured it as was described by the stretch and torque he mentioned]
beer

Re: Consistency of ARP rod bolt length [Re: moparx] #3090889
11/01/22 07:58 AM
11/01/22 07:58 AM
Joined: Jan 2003
Posts: 1,753
Windsor, ON, Canada
D
Diplomat360 Offline
top fuel
Diplomat360  Offline
top fuel
D

Joined: Jan 2003
Posts: 1,753
Windsor, ON, Canada
Originally Posted by moparx
agreed Cab. up
i was wondering what the OP got for a measurement on the big end. [if he measured it as was described by the stretch and torque he mentioned]
beer

Sorry, I'm a little late with the follow-up to your question.

Well, here is another table with the values.

My process actually was to:
1) put the rod in the rod-vise, go through 4 bolt tightening cycles
2) put the rod & bearings in the rod-vise, go through 1 more cycle and measure the bearing ID

All that goes into my table, which gives me an actual bearing clearance, as close to the operating conditions as possible (less heat, stretch, etc.).

Not sure why I had missed the 'HOUSING' size recording for the rods...or it could be that I just tossed that on my whiteboard and missed recording it in my spreadsheet.

All in all I got pretty consistent bearing clearance of 0.002 with a low spot of 0.0019 and a high of 0.0023, but given how tiny that difference is I was happy with the results.

mopar-crank-measurements.jpg
Re: Consistency of ARP rod bolt length [Re: moparx] #3091052
11/02/22 12:57 AM
11/02/22 12:57 AM
Joined: Jan 2003
Posts: 7,471
Minnesota
Hemi_Joel Offline OP
master
Hemi_Joel  Offline OP
master

Joined: Jan 2003
Posts: 7,471
Minnesota
Originally Posted by moparx
agreed Cab. up
i was wondering what the OP got for a measurement on the big end. [if he measured it as was described by the stretch and torque he mentioned]
beer


I haven't used torque for so long, I can't remember any measurements. I use an angle gauge, then measure stretch. The big ends check fine. If it takes more torque to achieve proper stretch on any given bolt, it shouldn't affect the big end distortion. Stretch is an indicator of clamping force. If the stretch is within spec, the clamping force should be equal regardless of how much torque it took to achieve it. Variations in the rolling of the threads during manufacturing can affect torque requirements.


[img]http://i.imgur.com/boeexFms.jpg[/img]
31 Plymouth Coupe, 392 Hemi, T56 magnum
RS23J71
RS27J77
RP23J71
RO23J71
WM21J8A
I don't regret the things I've done. I only regret the things I didn't do.
"Wise men talk because they have something to say; fools because they have to say something. ~ Plato"
Re: Consistency of ARP rod bolt length [Re: Hemi_Joel] #3091054
11/02/22 01:38 AM
11/02/22 01:38 AM
Joined: Aug 2003
Posts: 43,007
Bend,OR USA
C
Cab_Burge Offline
I Win
Cab_Burge  Offline
I Win
C

Joined: Aug 2003
Posts: 43,007
Bend,OR USA
I measured the ARP 2000 rod bolt stretch on a set of Scat 7.100 long rods with the Mopar big end today, I had to call Scat to try and get their recommended stretch and torque recommendations on thses bolt( 1.800 under head bolt length, 7/16 bolt diameter. No luck so i called the machine shop that I had pin fit these rods to the wrist pins in the pistons I'm going to use and had them check the rods for roundness and fit on the I.D for the rod bearings, they didn't return the instructions that came with those rods so I called then 2nd. They had to look and called me back and siad they didn't find the original sheet but looked on line at Scat site and came up with 70 Ft. lbs. with ARP lube and no longer than .0060 stretch.
My message is I saw around .0032 rod bolt length variances on these rod bolts with no load, I torque them all to70 Ft. Lbs. and that stretched them between .0041 up to .0053 shruggy
I'm thinking I will loosen several of them tomorrow and retorque them up to 75 Ft. lbs. and see if that helps getting them closer to .0057 up to .0060 luck


Mr.Cab Racing and winning with Mopars since 1964. (Old F--t, Huh)
Re: Consistency of ARP rod bolt length [Re: Cab_Burge] #3091072
11/02/22 07:52 AM
11/02/22 07:52 AM
Joined: May 2005
Posts: 1,944
Apollo, PA.
B1MAXX Offline
top fuel
B1MAXX  Offline
top fuel

Joined: May 2005
Posts: 1,944
Apollo, PA.
that won't get you up there. Don't chase the stretch number. 75lbs is fine.

Re: Consistency of ARP rod bolt length [Re: Hemi_Joel] #3091408
11/03/22 02:15 PM
11/03/22 02:15 PM
Joined: Sep 2003
Posts: 19,237
north of coder
moparx Offline
"Butt Crack Bob"
moparx  Offline
"Butt Crack Bob"

Joined: Sep 2003
Posts: 19,237
north of coder
Originally Posted by Hemi_Joel
Originally Posted by moparx
agreed Cab. up
i was wondering what the OP got for a measurement on the big end. [if he measured it as was described by the stretch and torque he mentioned]
beer


I haven't used torque for so long, I can't remember any measurements. I use an angle gauge, then measure stretch. The big ends check fine. If it takes more torque to achieve proper stretch on any given bolt, it shouldn't affect the big end distortion. Stretch is an indicator of clamping force. If the stretch is within spec, the clamping force should be equal regardless of how much torque it took to achieve it. Variations in the rolling of the threads during manufacturing can affect torque requirements.



Cab : "I measured the ARP 2000 rod bolt stretch on a set of Scat 7.100 long rods with the Mopar big end today, I had to call Scat to try and get their recommended stretch and torque recommendations on thses bolt( 1.800 under head bolt length, 7/16 bolt diameter. No luck so i called the machine shop that I had pin fit these rods to the wrist pins in the pistons I'm going to use and had them check the rods for roundness and fit on the I.D for the rod bearings, they didn't return the instructions that came with those rods so I called then 2nd. They had to look and called me back and siad they didn't find the original sheet but looked on line at Scat site and came up with 70 Ft. lbs. with ARP lube and no longer than .0060 stretch.
My message is I saw around .0032 rod bolt length variances on these rod bolts with no load, I torque them all to70 Ft. Lbs. and that stretched them between .0041 up to .0053 shruggy
I'm thinking I will loosen several of them tomorrow and retorque them up to 75 Ft. lbs. and see if that helps getting them closer to .0057 up to .0060 luck "......Cab

i think my old noodle is finally figuring this out. [torque plus stretch] i hope........
he!!, back in my junkyard days, when my partner [R.I.P. Bill. angel] and i built engines, we didn't know any more than to mic the crank, measure the inside of the caps with bearings installed, then use plastigauge to double check when the bolts/nuts were tightened. we didn't even calibrate the torque wrenches we were using !
fast forward to today, [50 years ! eek] it's a whole new science, so i haft'a learn new tricks, and unlearn my bad habits. whistling
thank you guys for being so patient with such a doofus as i have shown myself to be ! bow
beer







Powered by UBB.threads™ PHP Forum Software 7.7.1