I have a lightly used Holley 750 with mechanical secondaries, manual choke and 4 corner idle adjustment. This carb was used for some dyno sessions. It is set up with 72 jets in the front & 78 in the rear. Power valve is 4.5 in the front and the rear metering block is plugged. One minor modification was the front throttle blades were drilled for idle air. They were removed, the holes welded shut and reinstalled.

Carb is in excellent shape with little use.

Price is $400 plus shipping.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

For sale is a used set of 8 Diamond forged flat top pistons and pins for a 4.070 bore block and using a 4.000” stroke crankshaft. These pistons use a Chevy sized 0.927” wristpin. These were used in a street-strip engine for a few summers.

Bore (in.) 4.070 in.
Stroke 4.000 in.
Rod Length 6.125 in.
Piston Material Forged aluminum
Compression Height (in.) 1.457 in.
Piston Head Volume (cc) +5.60cc
Wrist Pin Style Floating
Pin Diameter (in.) 0.927 in.
Piston Ring Thickness 1/16 in. x 1/16 in. x 3/16 in.

Price is $400 plus shipping.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

New purchased from ProMax Carbs. Was $250
Goes from fuel pump to carbs includes pressure gauge and filter.
$195 shipped lower 48

For Sale. New in the box Scat 2-350-6125-2100A
https://www.summitracing.com/parts/sca-6612521a

$500
They retail for $695 so you're saving $200.

I bought these for a 3.79" crank build. Plans were to use a Molnar crankshaft. Molnar also has a 4.00" crank that these would work with.
These are NOT Chrysler spec rods. These are "Chevy" rods that are to be used with certain aftermarket Chrysler crankshafts ( https://www.molnartechnologies.com/domestic-crank-shafts/ )

They would also work for @Rocket 's pistons just above this post.

I will ship these for a flat rate of $25 to the lower 48. I will accept cash, check, money order, cashier's check, PayPal (Friends and Family), ...

This weekend (4/30 - 5/01) I can deliver anywhere near an interstate in SoCal, AZ, NM, West TX, or OK as I am driving from San Diego to OKC.

New in box Firestone D5025 inner tube. Valve stem TR218NRB (the large metal one).
Bought for my 13x31x15s as a spare.
Size also fits 10.5/28.5 through 30.5, 11.5/28.5 through 29.5W.
Half the cost new @ $40, add for shipping (I'll find cheapest way).

PM me here or email topside340@yahoo.com, especially May 5-14 when I'm out of town.

1964 Dodge b body fiberglass body parts. All parts are new. Only the fenders were mounted for fitment.
Front fenders $400.00 each
Front bumper $200.00
Deck lid $250.00
Doors $200.00 Each
Dash board $300.00
I do not know the manufacturer, no labels. Purchased with a project.
Fenders have some mounting holes drilled, everything else was never mounted to a car.
Some nicks and chips from handling and moving. Pick up only in Central New Jersey, I will not ship as it can and will get damaged by the shipper.
PM me through the board for more details
Ed

SOLD

RCI Platinum 5 Point Harness Expired
All hardware included, very little use.
$30 shipped in lower 48
PayPal or USPS money order
PM me on the board

Muscle Motors Oil Pump cover for external oil pickup.
New, never on an engine.
$150. PM me here.
SOLD !

Milodon Dual Line swinging oil pickup.
New. $100 PM me here.

Selling a brand new set of Molnar Chevy rods as I ended up going with a Mopar piston pin size. These would work great in and Chevy sized Mopar small block stroker engine and have been hard to get. Part number CH6125NLB8-A
600.00 plus shipping from 35 miles NE of Pittsburgh Pa

Also selling a very clean Holley Dominator carb. (Gas) List number 9377-2 (1150). I had two of these that have been sitting for years on my shelf. I sent one out last year to have it converted to alcohol. Probably could use new gaskets and go racing. My pictures end up sideways on this site so email me at jacadamore@gmail.com for pictures.
600.00 plus shipping from 16229 in Pa.




Sold. Sold. Sold. Sold. Sold. Sold

1968 426 HEMI Super Stock 727 torqueflite transmission for LO HEMI Darts & BO HEMI Barracudas $4500.00 (708) 288-2879

SOLD SOLD SOLD have a Meziere electric water pump for a big block Mopar
Ran briefly for 1 season works fine changed combo don’t need it anymore works good
$ 350 obo plus shipping USA only
Thanks Matt pm me here
I do take pay pal

2 inch 4 hole spacer-25.00 shipped tp lower 48. 4150 to 4500 adapter 75.00shipped to lower 48. pm me here.
SALE PENDING ON 2 INCH 4 HOLE SPACER.

Two bare powerglide case. One with
the bell cut off for Ultrabell use and
one modified (cut out) so a Mopar
starter would fit and then modified for
strength. 80.00 each and will not ship.
Keystone Raceway Park pickup
available.
Also selling a new set of .055 over 440
Mopar pistons for a stroker build using
a 4.250 crank. I ended up using .030
over pistons. These are from
440source and sell for 650.00. I'm
asking 525.00 plus shipping. Also have
rings available for above pistons that I
will include for 75.00 more (600.00
total plus shipping).

Pm or jacadamore@gmail.com.
For pictures.

foe sale Motive gear big pinion 4: 29 :1 ford 9 inch rear with bearing installed on pinion. like new maybe 40 passes, switched to 4:86 ratio , asking $265-00 plus shipping! Holley gen 3 number 80906 1150 carb like new switched to 1250 asking $750.00 or best offer. plus shipping! email dart10ss@aol.com or P M me.

cleaning out selling my older 8896 holly 1050 Dominator this carb was worked by Dwayne and later Dons carbs. works great , ran 9.00s with 529 cu in air fuel was always good ! asking $525 or B.O P M or email dart10ss@aol.com
Thanks for add moparts!

Posting for a friend
Big Block Mopar B-1 CFE Engineering Sheetmetal Dual Dominator Tunnel Ram Manifold for Low Deck Block
$2400.00 obo
Call Bob 831-239-3566

Pro Glass 1/8" Formed Lexan Door Windows and Innovative Racecraft Window Frames for Plymouth Duster, Dodge Demon, All BRAND NEW!! $600 plus the ride

PM or Email me: srrimay@gmail.com

Posting for a good friend of mine Brand New NRC predator heads fits hemi block heads,rockers,valve cover,header flanges and intake $6.500 obo call Ed at 510-928-3242 for more info

Selling a brand new set of TFS TFS-61617802-C00 heads - these are the Power Port 240s with the 1.55 springs and standard retainers (138 lb on the seat, 420 lb/in spring rate). I bought these for a project that changed directions. Still in TFS boxes and bags, were opened for inspection but never bolted on. $2500 OBO for the pair plus shipping. SALE PENDING ON THE HEADS

Also selling a new in box Track Heat Intake, same deal opened for inspection but never bolted on. $450 OBO plus shipping.