No lube seals, jesel belt drive?
#3020997
03/05/22 09:53 AM
03/05/22 09:53 AM
|
Joined: Jan 2003
Posts: 9,996 Frostbitefalls MN (Rocky&Bullw...
gregsdart
OP
master
|
OP
master
Joined: Jan 2003
Posts: 9,996
Frostbitefalls MN (Rocky&Bullw...
|
Ok, i was asleep and put assembly lube on the seals of my belt drive🙄so, does it destroy the seal if run? I must think it does, since the instructions say no lobe. I am hoping to avoid pulling it back apart to clean it up, but figure odds on doing that are low. Your experiences, or info from jesel?
8..603 156 mph best, 2905 lbs 549, indy 572-13, alky
|
|
|
Re: No lube seals, jesel belt drive?
[Re: gregsdart]
#3021011
03/05/22 11:30 AM
03/05/22 11:30 AM
|
Joined: Jan 2003
Posts: 16,925 NC
440Jim
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 16,925
NC
|
Greg, I have no idea. Those are the first rubber lip seals I have used with their dry coating. CHECK CAMSHAFT END PLAY BY SETTING A DIAL INDICATOR ON THE FACE OF THE CAM ADAPTOR AND MOVE CAM FRONT TO BACK. ADJUST THE SHIMS UNTIL THE CAMSHAFT ENDPLAY IS BETWEEN .008” AND .012”. IT IS OK TO USE ZERO SHIMS, IF CAM ENDPLAY IS CORRECT. REMOVE THRUST PLATE AND SHIMS. APPLY A VERY THIN FILM OF RTV SEALANT BETWEEN SHIMS TO PREVENT POSSIBLE OIL LEAKAGE. REINSTALL REQUIRED SHIMS AND THRUST PLATE AND RETORQUE NUTS. * KEEP OIL OFF SEAL AREA. * BE CAREFUL NOT TO DAMAGE SEAL ON ADAPTOR KEYWAY.
How much shim did you need to get your cam endplay? And what timing cover gasket thickness did you use (effects end play)? I didn't need any of the supplied shims with an 0.047" gasket. (SuperPerformance brand)
|
|
|
Re: No lube seals, jesel belt drive?
[Re: 440Jim]
#3021016
03/05/22 11:49 AM
03/05/22 11:49 AM
|
Joined: Jan 2003
Posts: 10,022 MN
JERICOGTX
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 10,022
MN
|
Cummins engines use a rear main seal that is similar. My buddy put a light coat of oil on his, and it leaked horribly. Put the second one in dry, and no leaks. I’d be cleaning yours.
69 GTX
68 Road Runner
|
|
|
Re: No lube seals, jesel belt drive?
[Re: 440Jim]
#3021032
03/05/22 01:11 PM
03/05/22 01:11 PM
|
Joined: Jan 2003
Posts: 9,996 Frostbitefalls MN (Rocky&Bullw...
gregsdart
OP
master
|
OP
master
Joined: Jan 2003
Posts: 9,996
Frostbitefalls MN (Rocky&Bullw...
|
Greg, I have no idea. Those are the first rubber lip seals I have used with their dry coating. CHECK CAMSHAFT END PLAY BY SETTING A DIAL INDICATOR ON THE FACE OF THE CAM ADAPTOR AND MOVE CAM FRONT TO BACK. ADJUST THE SHIMS UNTIL THE CAMSHAFT ENDPLAY IS BETWEEN .008” AND .012”. IT IS OK TO USE ZERO SHIMS, IF CAM ENDPLAY IS CORRECT. REMOVE THRUST PLATE AND SHIMS. APPLY A VERY THIN FILM OF RTV SEALANT BETWEEN SHIMS TO PREVENT POSSIBLE OIL LEAKAGE. REINSTALL REQUIRED SHIMS AND THRUST PLATE AND RETORQUE NUTS. * KEEP OIL OFF SEAL AREA. * BE CAREFUL NOT TO DAMAGE SEAL ON ADAPTOR KEYWAY.
How much shim did you need to get your cam endplay? And what timing cover gasket thickness did you use (effects end play)? I didn't need any of the supplied shims with an 0.047" gasket. (SuperPerformance brand) Jim, .008 thick gasket, one . 010 shim gave . 009 play, but shims had been lubed with assembly lube.
Last edited by gregsdart; 03/05/22 01:12 PM.
8..603 156 mph best, 2905 lbs 549, indy 572-13, alky
|
|
|
Re: No lube seals, jesel belt drive?
[Re: JERICOGTX]
#3021034
03/05/22 01:14 PM
03/05/22 01:14 PM
|
Joined: Jan 2003
Posts: 9,996 Frostbitefalls MN (Rocky&Bullw...
gregsdart
OP
master
|
OP
master
Joined: Jan 2003
Posts: 9,996
Frostbitefalls MN (Rocky&Bullw...
|
Cummins engines use a rear main seal that is similar. My buddy put a light coat of oil on his, and it leaked horribly. Put the second one in dry, and no leaks. I’d be cleaning yours. thanks Jeff.
8..603 156 mph best, 2905 lbs 549, indy 572-13, alky
|
|
|
Re: No lube seals, jesel belt drive?
[Re: gregsdart]
#3021043
03/05/22 02:04 PM
03/05/22 02:04 PM
|
Joined: Jan 2003
Posts: 19,363 Las Vegas
Al_Alguire
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 19,363
Las Vegas
|
Absolutely NO LUBE on those seals!
"I am not ashamed to confess I am ignorant of what I do not know."
"It's never wrong to do the right thing"
|
|
|
Re: No lube seals, jesel belt drive?
[Re: gregsdart]
#3021112
03/05/22 07:48 PM
03/05/22 07:48 PM
|
Joined: Feb 2003
Posts: 911 London, England
mopar_mark
super stock
|
super stock
Joined: Feb 2003
Posts: 911
London, England
|
Now the question is, can i clean the seals and surfaces, and if so, what with? Brake cleaner should work fine & wont affect the Teflon
|
|
|
Re: No lube seals, jesel belt drive?
[Re: gregsdart]
#3021159
03/05/22 10:57 PM
03/05/22 10:57 PM
|
Joined: Mar 2003
Posts: 9,099 Rogue River, OR
Jeremiah
master
|
master
Joined: Mar 2003
Posts: 9,099
Rogue River, OR
|
Now the question is, can i clean the seals and surfaces, and if so, what with? Any top shelf bourbon should work.
|
|
|
Re: No lube seals, jesel belt drive?
[Re: gregsdart]
#3021190
03/06/22 07:49 AM
03/06/22 07:49 AM
|
Joined: Jul 2018
Posts: 169 Sticky South
Rodenteliminator
member
|
member
Joined: Jul 2018
Posts: 169
Sticky South
|
Starting Fluid / Ether is a very good cleaner if the smell doesn’t bother you or you are next to anything with a flame, it leaves a very clean and dry surface, it’s what I wipe down the surfaces with before gasket install. It will remove decal glue on paint and not damage paint etc. Doug
Sorry honey I spent the rent
|
|
|
Re: No lube seals, jesel belt drive?
[Re: Rodenteliminator]
#3021455
03/07/22 10:39 AM
03/07/22 10:39 AM
|
Joined: Mar 2005
Posts: 1,581 N/E, Michigan
RATTRAP
pro stock
|
pro stock
Joined: Mar 2005
Posts: 1,581
N/E, Michigan
|
Starting Fluid / Ether is a very good cleaner if the smell doesn’t bother you or you are next to anything with a flame, it leaves a very clean and dry surface, it’s what I wipe down the surfaces with before gasket install. It will remove decal glue on paint and not damage paint etc. Doug "Acetone"
|
|
|
Re: No lube seals, jesel belt drive?
[Re: Cab_Burge]
#3021592
03/07/22 06:17 PM
03/07/22 06:17 PM
|
Joined: Jan 2003
Posts: 9,996 Frostbitefalls MN (Rocky&Bullw...
gregsdart
OP
master
|
OP
master
Joined: Jan 2003
Posts: 9,996
Frostbitefalls MN (Rocky&Bullw...
|
I called Jesel, and the tech said use mild dish soap and it MIGHT work. So i ordered a set od double lip teflon seals, since that was his recomendation after my saying i wanted to pull 12+ inchs of vacuum. So all looks good, but the cost. $130 for double lip teflon seals. On the up side, i have two important items for high vacuum. DLC coated piston pins, and good seals.
8..603 156 mph best, 2905 lbs 549, indy 572-13, alky
|
|
|
|
|