Carter choke pull off and thermostat on an Eddy AVS2? - Moparts Forums

Register Log In Moparts Forums Moparts Question and Answer Carter choke pull off and thermostat on an Eddy AVS2?

Print Thread

Carter choke pull off and thermostat on an Eddy AVS2? #2998497 12/25/21 11:15 PM 12/25/21 11:15 PM
Joined: Feb 2003 Posts: 7,982 Scranton, PA Montclaire OP master
Montclaire OP master Joined: Feb 2003 Posts: 7,982 Scranton, PA	I have an 800cfm AVS2 carb, manual choke. I'm wondering if I can add a Carter choke pull off and thermostat to mimic the factory 70/71 setup. Has anyone tried this? I'm not sure why but Edelbrock says that you can't add an electric choke to their manual choke AVS2s. They seem to have the same brass plug as the AFBs (not just leaded over) and the bosses are there where the pull off should mount. Can I run the pull off to ported vacuum and bypass the choke port? Both the pull off and thermostat are reproduced. I might have a hard time with the choke shaft lever, not sure how compatible the newer and older shafts are. Thanks

Re: Carter choke pull off and thermostat on an Eddy AVS2? [Re: Montclaire] #2998549 12/26/21 08:03 AM 12/26/21 08:03 AM
Joined: Jun 2008 Posts: 3,916 usa L lewtot184 master
lewtot184 master L Joined: Jun 2008 Posts: 3,916 usa	i did it to a 1407. don't see any reason it can't be done to a 800. i put factory choke parts on the carb in the photos to use on a stock iron intake. also changed out the primary throttle shaft. Last edited by lewtot184; 12/26/21 08:05 AM.

Re: Carter choke pull off and thermostat on an Eddy AVS2? [Re: lewtot184] #2998735 12/26/21 11:01 PM 12/26/21 11:01 PM
Joined: Feb 2003 Posts: 7,982 Scranton, PA Montclaire OP master
Montclaire OP master Joined: Feb 2003 Posts: 7,982 Scranton, PA	Is there any reason to change the throttle shaft other than cosmetics? I'm not going for full OE, I just want a non-electric choke. Kickdown and throttle linkage were working well enough as-is.

Re: Carter choke pull off and thermostat on an Eddy AVS2? [Re: Montclaire] #2998769 12/27/21 09:23 AM 12/27/21 09:23 AM
Joined: Jun 2008 Posts: 3,916 usa L lewtot184 master
lewtot184 master L Joined: Jun 2008 Posts: 3,916 usa	i had a shaft from a junk carter carb and didn't want to use the edelbrock adapter. i wanted to mimic the appearance of a stock carb.

Re: Carter choke pull off and thermostat on an Eddy AVS2? [Re: lewtot184] #2998817 12/27/21 12:18 PM 12/27/21 12:18 PM
Joined: Jan 2003 Posts: 20,723 A collage of whims topside Too Many Posts
topside Too Many Posts Joined: Jan 2003 Posts: 20,723 A collage of whims	I modified my manual-choke AVS2 to look like the original AVS on my '68: Shaved the Eddie tag Tapped choke pull-off holes & installed repro pull-off unit Changed inlet fitting The pull-off rod & choke rod differ from OEM, as does the arm on the primary shaft, IIRC. Since it never sees cold temps I left the choke disconnected. Might revisit that at some point

Re: Carter choke pull off and thermostat on an Eddy AVS2? [Re: topside] #2998883 12/27/21 02:51 PM 12/27/21 02:51 PM
Joined: Jun 2008 Posts: 3,916 usa L lewtot184 master
lewtot184 master L Joined: Jun 2008 Posts: 3,916 usa	to hook all the stuff up to a stock intake then all mopar factory choke parts make it very easy. the cross shaft that connects both sides is longer on factory than edelbrocks. i had donner parts and basically i just copied a factory install. it works.

Re: Carter choke pull off and thermostat on an Eddy AVS2? [Re: lewtot184] #2999036 12/27/21 10:00 PM 12/27/21 10:00 PM
Joined: Jan 2003 Posts: 15,265 Omaha Ne T TJP I Live Here
TJP I Live Here T Joined: Jan 2003 Posts: 15,265 Omaha Ne	NICE!!!! work www.tandmautomotive-omaha.com

Re: Carter choke pull off and thermostat on an Eddy AVS2? [Re: lewtot184] #3003592 01/09/22 08:52 PM 01/09/22 08:52 PM
Joined: Feb 2003 Posts: 7,982 Scranton, PA Montclaire OP master
Montclaire OP master Joined: Feb 2003 Posts: 7,982 Scranton, PA	Originally Posted by lewtot184 to hook all the stuff up to a stock intake then all mopar factory choke parts make it very easy. the cross shaft that connects both sides is longer on factory than edelbrocks. i had donner parts and basically i just copied a factory install. it works. Does anyone reproduce the shaft? I have the triangle shaped piece for the end of the choke rod, and it looks like both the vacuum and mechanical pull offs are repopped.

Re: Carter choke pull off and thermostat on an Eddy AVS2? [Re: Montclaire] #3003711 01/10/22 08:51 AM 01/10/22 08:51 AM
Joined: Jun 2008 Posts: 3,916 usa L lewtot184 master
lewtot184 master L Joined: Jun 2008 Posts: 3,916 usa	Originally Posted by Montclaire Originally Posted by lewtot184 to hook all the stuff up to a stock intake then all mopar factory choke parts make it very easy. the cross shaft that connects both sides is longer on factory than edelbrocks. i had donner parts and basically i just copied a factory install. it works. Does anyone reproduce the shaft? I have the triangle shaped piece for the end of the choke rod, and it looks like both the vacuum and mechanical pull offs are repopped. to the best of my knowledge the cross shaft is unique to the factory avs. i had some spare parts and that made conversion simpler.

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1