Previous Thread
Next Thread
Print Thread
Page 2 of 2 1 2
Re: A833 Three Number Stamp [Re: ogopogo] #2916817
04/30/21 03:53 AM
04/30/21 03:53 AM
Joined: Mar 2011
Posts: 1,651
Cut and Shoot, TX
kentj340 Offline
top fuel
kentj340  Offline
top fuel

Joined: Mar 2011
Posts: 1,651
Cut and Shoot, TX
The numbers on my transmission were 2" high, 2-3/8" wide. I downloaded for free the font Placard Condensed (not Placard MT Std Cond which is similar but not as correct) and made a master "602" with numbers 2" high. I think the rubber stamp needs some margin around the perimeter, so it needs to be slightly larger.

At RubberStamps.net, I uploaded my master and ordered a stamp 2.5" high x 3" wide, part number WOODSTAMP77, about $24. This is one stamp with three numbers, which is better than three stamps of one number each..

Because the margin around the rubber part of the stamp in the last photo seems unnecessarily large, it looks like maybe I could have ordered a smaller stamp 2.25" high x 2.5" wide, but I don't know if that size is available.


21-15 Transmission.  Markings8.jpg21-15 Transmission.  Markings9.jpgIMG_1222.jpgIMG_1223.jpg

If you don't see two dolphins, you need a vacation.
Re: A833 Three Number Stamp [Re: ogopogo] #2916848
04/30/21 08:14 AM
04/30/21 08:14 AM
Joined: Dec 2011
Posts: 892
MA
steve70 Offline
super stock
steve70  Offline
super stock

Joined: Dec 2011
Posts: 892
MA
Originally Posted by ogopogo
Anyone have the dimensions of this stamp ,height by width?

Picture 205small.jpgPicture 207small.jpg

1970 Challenger T/A 4 speed
Re: A833 Three Number Stamp [Re: steve70] #2922201
05/13/21 06:54 PM
05/13/21 06:54 PM
Joined: Oct 2003
Posts: 1,794
BC Canada
O
ogopogo Offline
top fuel
ogopogo  Offline
top fuel
O

Joined: Oct 2003
Posts: 1,794
BC Canada
thank you !

Re: A833 Three Number Stamp [Re: ogopogo] #2922208
05/13/21 07:11 PM
05/13/21 07:11 PM
Joined: Jul 2003
Posts: 3,267
Connecticut
1972CudaV21 Offline
master
1972CudaV21  Offline
master

Joined: Jul 2003
Posts: 3,267
Connecticut
On the tail shaft of a 727 transmission, I’ve seen hand-painted numbers with 3 digits. Is there any relationship between the 3 numbers and a part number?

0B88E8FC-189C-4C38-8A31-8DD1B7D65042.jpeg

China is the enemy.
Re: A833 Three Number Stamp [Re: 1972CudaV21] #2922654
05/14/21 11:41 PM
05/14/21 11:41 PM
Joined: Jan 2003
Posts: 15,662
Jefferson State
S
srt Online content
ESYC
srt  Online Content
ESYC
S

Joined: Jan 2003
Posts: 15,662
Jefferson State
Don't quote me on this, I read here years ago that designates the prop shaft to be used. If anyone can verify, I'd like to hear, and also find out if there is a spreadsheet.

Re: A833 Three Number Stamp [Re: srt] #2922688
05/15/21 04:34 AM
05/15/21 04:34 AM
Joined: Jul 2003
Posts: 3,267
Connecticut
1972CudaV21 Offline
master
1972CudaV21  Offline
master

Joined: Jul 2003
Posts: 3,267
Connecticut
Originally Posted by srt
Don't quote me on this, I read here years ago that designates the prop shaft to be used. If anyone can verify, I'd like to hear, and also find out if there is a spreadsheet.


Are you referring to the driveshaft yoke?


China is the enemy.
Re: A833 Three Number Stamp [Re: 1972CudaV21] #2922909
05/15/21 06:16 PM
05/15/21 06:16 PM
Joined: Jan 2003
Posts: 15,662
Jefferson State
S
srt Online content
ESYC
srt  Online Content
ESYC
S

Joined: Jan 2003
Posts: 15,662
Jefferson State
I believe it may have to do with the assembly number of the driveshaft. Post (or article) I read years ago and probably have it filed someplace.
Again do not quote me on this. It may have been sonething aboiut the yokes at each end. i.e. trac pac behind an auto vs 4 speed
a non hemi / 440 was spec'ed for a dana may have required different rear yoke?
What was the tail shaft you have from?

Re: A833 Three Number Stamp [Re: srt] #2922931
05/15/21 07:20 PM
05/15/21 07:20 PM
Joined: Jul 2003
Posts: 3,267
Connecticut
1972CudaV21 Offline
master
1972CudaV21  Offline
master

Joined: Jul 2003
Posts: 3,267
Connecticut
Originally Posted by srt
I believe it may have to do with the assembly number of the driveshaft. Post (or article) I read years ago and probably have it filed someplace.
Again do not quote me on this. It may have been sonething aboiut the yokes at each end. i.e. trac pac behind an auto vs 4 speed
a non hemi / 440 was spec'ed for a dana may have required different rear yoke?
What was the tail shaft you have from?


That image is from an online magazine and not mine. I’m rebuilding my 727 and I’d like to learn more about inspection marks, numbers, etc. Here is another from a member on here:

ECD6AC66-9565-4C9D-B83A-7C37F791DA2E.jpeg

China is the enemy.
Page 2 of 2 1 2






Powered by UBB.threads™ PHP Forum Software 7.7.1