|
Re: A body header question
[Re: wyldebill]
#2632138
03/13/19 03:57 AM
03/13/19 03:57 AM
|
Joined: Dec 2006
Posts: 4,647 aotearoa
rebel
master
|
master
Joined: Dec 2006
Posts: 4,647
aotearoa
|
The biggest problem is the shock mount is in the way for anything with nice flowing primaries. I eventually cut the shock mount down & moved the upper mount onto my cage. Then it was a simple case of make my own headers. If you're still running inner fenders, you're going to be screwed, tight bends that make plug access hard are going to be your nightmare.
Last edited by rebel; 03/13/19 04:00 AM.
|
|
|
Re: A body header question
[Re: wyldebill]
#2632427
03/13/19 09:05 PM
03/13/19 09:05 PM
|
Joined: Aug 2003
Posts: 4,673 On the parachute mount
n20mstr
master
|
master
Joined: Aug 2003
Posts: 4,673
On the parachute mount
|
Try a b body header, but be prepared to cut up and move one or more tubes. Buy cheap headers and cut off th collector and cut the flange so you can install one tube at a time. Or get a couple sets of used headers I'm sure you can make a set that way. When done get a slip on collector.
....BAD A$$ STREET CAR.....
|
|
|
Re: A body header question
[Re: wyldebill]
#2633101
03/15/19 05:36 PM
03/15/19 05:36 PM
|
Joined: Feb 2007
Posts: 2,578 sweden
1Fast340
master
|
master
Joined: Feb 2007
Posts: 2,578
sweden
|
Hey folks. I don't know when my new engine will be finished, so I was thinking about dropping a milder 400 in my valiant. What I'm curious about, what header can I get away with running? It's a standard port low deck. Aftermarket k member so no torsion bars to get in the way. I cant run the headers for the car. Raised port 2.25 primary. Will a b body header work? This is relatively temporary, so I don't want to buy a tti or spend a ton of money here. Any recommendations? Thanks Bill Do some research on the 1 3/4" Hedman B-body headers. Plenty has been writen about them fitting lowdeck abodies with just a few dings unless something has changed recently.
|
|
|
Re: A body header question
[Re: 1Fast340]
#2633380
03/16/19 03:04 PM
03/16/19 03:04 PM
|
Joined: Jan 2003
Posts: 4,395 The Pale Blue Dot
Skeptic
master
|
master
Joined: Jan 2003
Posts: 4,395
The Pale Blue Dot
|
Hey folks. I don't know when my new engine will be finished, so I was thinking about dropping a milder 400 in my valiant. What I'm curious about, what header can I get away with running? It's a standard port low deck. Aftermarket k member so no torsion bars to get in the way. I cant run the headers for the car. Raised port 2.25 primary. Will a b body header work? This is relatively temporary, so I don't want to buy a tti or spend a ton of money here. Any recommendations? Thanks Bill Do some research on the 1 3/4" Hedman B-body headers. Plenty has been writen about them fitting lowdeck abodies with just a few dings unless something has changed recently. Don't use the "Elite" Headman headers, the # 3 and 7 tubes are a mess, even with a MS box. If you have a rack steering box, this may not matter,
|
|
|
|
|
|