Tool ID
#2565461
10/17/18 05:16 PM
10/17/18 05:16 PM
|
Joined: Jan 2003
Posts: 25,899 Rio Linda, CA
John_Kunkel
OP
Too Many Posts
|
OP
Too Many Posts
Joined: Jan 2003
Posts: 25,899
Rio Linda, CA
|
This crimper is stamped:
AMP Type O 16-14 59498
16-14 is likely the wire gauge but the jaws are about 3/8" diameter, a little big for that wire gauge.
The INTERNET, the MISinformation superhighway
|
|
|
Re: Tool ID
[Re: John_Kunkel]
#2565467
10/17/18 05:29 PM
10/17/18 05:29 PM
|
Joined: Jan 2003
Posts: 4,737 Moved to N.E. Tennessee
GomangoCuda
master
|
master
Joined: Jan 2003
Posts: 4,737
Moved to N.E. Tennessee
|
Maybe it's for O gage and 16-14 is the tool number. Or maybe it came with a diffent set of dies than what is currently installed.
Last edited by GomangoCuda; 10/17/18 05:34 PM.
In theory, there is no difference between theory and practice. In practice, there is.
|
|
|
Re: Tool ID
[Re: John_Kunkel]
#2565554
10/17/18 08:03 PM
10/17/18 08:03 PM
|
Joined: Jan 2003
Posts: 28,068 Irving, TX
feets
Senior Management
|
Senior Management
Joined: Jan 2003
Posts: 28,068
Irving, TX
|
I'm thinking it's got a different set of dies in it.
We are brothers and sisters doing time on the planet for better or worse. I'll take the better, if you don't mind. - Stu Harmon
|
|
|
Re: Tool ID
[Re: John_Kunkel]
#2565556
10/17/18 08:05 PM
10/17/18 08:05 PM
|
Joined: Jan 2003
Posts: 4,737 Moved to N.E. Tennessee
GomangoCuda
master
|
master
Joined: Jan 2003
Posts: 4,737
Moved to N.E. Tennessee
|
Agree that Amp is very big in electrical connectors and crimpers. I think it was sold as a 16-14 crimper and has had the dies changed since then.
In theory, there is no difference between theory and practice. In practice, there is.
|
|
|
Re: Tool ID
[Re: moparmarks]
#2565575
10/17/18 08:42 PM
10/17/18 08:42 PM
|
Joined: Jul 2008
Posts: 75 Lakeland, FL
sixpakchallenger
member
|
member
Joined: Jul 2008
Posts: 75
Lakeland, FL
|
The "O" die is for distribution electrical connectors, typically H-taps. Probably #1 stranded aluminum to #6 solid copper to feed a transformer.
2007 Mustang GT Vert 2004 Ram 2500 QC 4X4 1971 Challenger Vert 5.7 Hemi Project
|
|
|
Re: Tool ID
[Re: John_Kunkel]
#2566916
10/20/18 02:02 PM
10/20/18 02:02 PM
|
Joined: Feb 2014
Posts: 1,710 central il.
second 70
top fuel
|
top fuel
Joined: Feb 2014
Posts: 1,710
central il.
|
I had used several different amp crimpers over the years as a lineman. Some have changeable dies others don't. The O is a common size used on most house service sleeves. We had sleeves from #6 to #1/0 that used the same die. I believe O is 5/8. They make what we call an O D tool that had 1 fixed opening O and one that take dies. Meaning fixed O and die’s. Also called a one shot. We found a couple that had a 9/16 fixed instead of the 5/8 too. Depending on who's sleeves your using you sometimes need a different die for the same size wire. Most new crimper's are either ratchet, hydraulic, battery-operated and insulated.
Those were dangerous on live wire with the long metal handles.
Last edited by second 70; 10/20/18 04:38 PM.
|
|
|
|
|