how to install steering pump pulley on a TRW pump - Moparts Forums

Register Log In Moparts Forums Moparts Question and Answer how to install steering pump pulley on a TRW pump

Print Thread

how to install steering pump pulley on a TRW pump #2061841 04/26/16 02:42 AM 04/26/16 02:42 AM
Joined: Jan 2003 Posts: 1,547 Puyallup, Wa. S Steve340 OP pro stock
Steve340 OP pro stock S Joined: Jan 2003 Posts: 1,547 Puyallup, Wa.	Does anyone have a 1966 manual that shows how to remove and install the pulley on a 1966 Chrysler pump. It has a hex hole on the end of the shaft. I know on the federal you thread in a bolt and nut and turn the nut to put it on, but this one has no threaded hole,just a hex hole

Re: how to install steering pump pulley on a TRW pump [Re: Steve340] #2061911 04/26/16 10:43 AM 04/26/16 10:43 AM
Joined: Sep 2003 Posts: 19,310 north of coder moparx "Butt Crack Bob"
moparx "Butt Crack Bob" Joined: Sep 2003 Posts: 19,310 north of coder	you are in luck. pm me your email address and i will scan and send you the procedures direct from a FSM in a pdf file. is the pulley removal/installation the only info you need, or do you also need the pages describing the re-build process ?

Re: how to install steering pump pulley on a TRW pump [Re: Steve340] #2062343 04/26/16 11:03 PM 04/26/16 11:03 PM
Joined: Sep 2007 Posts: 14,889 up yours Supercuda About to go away
Supercuda About to go away Joined: Sep 2007 Posts: 14,889 up yours	I have a 65 FSM, if it's the same then the tool I think you can use is http://www.autozone.com/loan-a-tools/pow.../?checkfit=true to pull it, you press it back on. They say there are no such thing as a stupid question. They say there is always the exception that proves the rule. Don't be the exception.

Re: how to install steering pump pulley on a TRW pump [Re: Supercuda] #2062590 04/27/16 10:33 AM 04/27/16 10:33 AM
Joined: Sep 2003 Posts: 19,310 north of coder moparx "Butt Crack Bob"
moparx "Butt Crack Bob" Joined: Sep 2003 Posts: 19,310 north of coder	that's the tool. used to pull alternator pulleys also.

Re: how to install steering pump pulley on a TRW pump [Re: moparx] #2062711 04/27/16 02:26 PM 04/27/16 02:26 PM
Joined: Jan 2003 Posts: 15,279 Omaha Ne T TJP I Live Here
TJP I Live Here T Joined: Jan 2003 Posts: 15,279 Omaha Ne	I believe the pump has to be dismantled to press the pulley back on without damaging the pump. www.tandmautomotive-omaha.com

Re: how to install steering pump pulley on a TRW pump [Re: TJP] #2062798 04/27/16 05:02 PM 04/27/16 05:02 PM
Joined: Jan 2003 Posts: 25,729 Rio Linda, CA John_Kunkel Too Many Posts
John_Kunkel Too Many Posts Joined: Jan 2003 Posts: 25,729 Rio Linda, CA	Correct, just like an alternator, the unit must be disassembled and the rear of the pump shaft supported when pressing on the pulley. The INTERNET, the MISinformation superhighway

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1