Re: Water/Meth Injection
[Re: racealittle]
#1411529
04/02/13 08:11 PM
04/02/13 08:11 PM
|
Anonymous
Unregistered
|
Anonymous
Unregistered
|
I was just looking at the snow unit, $400 plus.
|
|
|
Re: Water/Meth Injection
[Re: megajoltman]
#1411531
04/03/13 02:40 AM
04/03/13 02:40 AM
|
Joined: Jan 2003
Posts: 3,842 N.E. Ohio
6bblFLASH
OP
master
|
OP
master
Joined: Jan 2003
Posts: 3,842
N.E. Ohio
|
Mainbody: This area was hollow so I epoxied it solid. I may endup boring out the base and threading the nozzle directly into the mainbody IF it blows out the gasket
Last edited by 6bblFLASH; 04/03/13 02:43 AM.
70` Cuda`,440 6BBL Jerico,Dana 4.56 Still on 93 Pump Gas 9.87 @ 136/1.31-60ft.`09 Mopar Nationals PASSON PERFORMANCE "Stick-Shift" Champ! 2013 StickShift Challenge Winner@ Mopar Nationals!
|
|
|
Re: Water/Meth Injection
[Re: 6bblFLASH]
#1411532
04/03/13 02:45 AM
04/03/13 02:45 AM
|
Joined: Jan 2003
Posts: 3,842 N.E. Ohio
6bblFLASH
OP
master
|
OP
master
Joined: Jan 2003
Posts: 3,842
N.E. Ohio
|
Base is drilled and tapped for nozzle. Fitting just for example
Last edited by 6bblFLASH; 04/03/13 02:46 AM.
70` Cuda`,440 6BBL Jerico,Dana 4.56 Still on 93 Pump Gas 9.87 @ 136/1.31-60ft.`09 Mopar Nationals PASSON PERFORMANCE "Stick-Shift" Champ! 2013 StickShift Challenge Winner@ Mopar Nationals!
|
|
|
Re: Water/Meth Injection
[Re: 6bblFLASH]
#1411533
04/03/13 02:48 AM
04/03/13 02:48 AM
|
Joined: Jan 2003
Posts: 3,842 N.E. Ohio
6bblFLASH
OP
master
|
OP
master
Joined: Jan 2003
Posts: 3,842
N.E. Ohio
|
Passage in side of mainbody intersects with passage out the bottom,also threaded to plumb water/meth to the nozzle.
70` Cuda`,440 6BBL Jerico,Dana 4.56 Still on 93 Pump Gas 9.87 @ 136/1.31-60ft.`09 Mopar Nationals PASSON PERFORMANCE "Stick-Shift" Champ! 2013 StickShift Challenge Winner@ Mopar Nationals!
|
|
|
Re: Water/Meth Injection
[Re: 6bblFLASH]
#1411535
04/03/13 02:53 AM
04/03/13 02:53 AM
|
Joined: Jan 2003
Posts: 3,842 N.E. Ohio
6bblFLASH
OP
master
|
OP
master
Joined: Jan 2003
Posts: 3,842
N.E. Ohio
|
Its just that simple. Took me all of an hour with a hand drill. Laided awake for HOURS coming up with the idea. I have`nt come up with any reasons why it won`t work ........ Thoughts?
Last edited by 6bblFLASH; 04/03/13 04:55 PM.
70` Cuda`,440 6BBL Jerico,Dana 4.56 Still on 93 Pump Gas 9.87 @ 136/1.31-60ft.`09 Mopar Nationals PASSON PERFORMANCE "Stick-Shift" Champ! 2013 StickShift Challenge Winner@ Mopar Nationals!
|
|
|
Re: Water/Meth Injection
[Re: challengermike]
#1411540
04/04/13 01:37 AM
04/04/13 01:37 AM
|
Joined: Jan 2003
Posts: 3,842 N.E. Ohio
6bblFLASH
OP
master
|
OP
master
Joined: Jan 2003
Posts: 3,842
N.E. Ohio
|
Possible.but it can't puddle any worse than shooting against the wall of a 3in tube like everyone else does. No I'm not worried about distribution. Where things go inside there is anyone s. guess.I guess I could use a"T" and run two really small nozzles spraying outward. With 2 rotors spinning 10, 000rpm I doubt it will matter. Getting a nozzle from McMaster.625ml and a couple other sizes to play with. Their nozzle is very short and will bearly extend past bottom of the carb. giving it the max distance to fan out
Last edited by 6bblFLASH; 04/04/13 01:52 AM.
|
|
|
Re: Water/Meth Injection
[Re: 6bblFLASH]
#1411543
04/04/13 02:25 AM
04/04/13 02:25 AM
|
Joined: Oct 2003
Posts: 3,698 NE Oklahoma
Von
master
|
master
Joined: Oct 2003
Posts: 3,698
NE Oklahoma
|
Quote:
4# This what I`m trying to avoid.
Is that a KB hyper piston?
72 RR, Pump gas 440, 452s, 3800 lbs, Corked, ET Radials,. 11.33@117.72.
Same car, bone stock 346s, 9.5 comp, baby solid. 12.24@110.
|
|
|
Re: Water/Meth Injection
[Re: Clanton]
#1411547
04/04/13 04:44 PM
04/04/13 04:44 PM
|
Joined: Jan 2003
Posts: 3,842 N.E. Ohio
6bblFLASH
OP
master
|
OP
master
Joined: Jan 2003
Posts: 3,842
N.E. Ohio
|
All valid questions and comments, I`d be BS`ing if I said for sure it will work perfect. As far as a Snow Kit I won`t need everything now,but that is what I wanted initially. Nozzles are open ended choice LOTS of different vendors. McMaster Carr has really cheap ones. 4.00 each and only measure 3/4" long. Perfect for where I`m putting them. If I understand it all: get a nozzle size in range,,,, use pressure to fine tune,,,,mixture is another fine tune tool. Snow says " get AFR to 12.5 WITHOUT water,then with water ON should should lose no more than .5 AFR I.E.- 12.0 +. That will be safe. Then you can add timing/boost..... Experiment at your own risk from there So general place to start is 625ml/10gph nozzle at about 60psi. Plan on using "BoostJuice" first then home brewed blends later. Any other tpis/results/experiences?
70` Cuda`,440 6BBL Jerico,Dana 4.56 Still on 93 Pump Gas 9.87 @ 136/1.31-60ft.`09 Mopar Nationals PASSON PERFORMANCE "Stick-Shift" Champ! 2013 StickShift Challenge Winner@ Mopar Nationals!
|
|
|
Re: Water/Meth Injection
[Re: 6bblFLASH]
#1411548
04/07/13 06:00 AM
04/07/13 06:00 AM
|
Joined: Jan 2003
Posts: 3,842 N.E. Ohio
6bblFLASH
OP
master
|
OP
master
Joined: Jan 2003
Posts: 3,842
N.E. Ohio
|
Nobody uses water/meth? Whats your tip size/HP. What mix are you using? Before and after results?
70` Cuda`,440 6BBL Jerico,Dana 4.56 Still on 93 Pump Gas 9.87 @ 136/1.31-60ft.`09 Mopar Nationals PASSON PERFORMANCE "Stick-Shift" Champ! 2013 StickShift Challenge Winner@ Mopar Nationals!
|
|
|
|
|