PORTING 906 HEADS AROUND THE VALVES-SHROUDING - Moparts Forums

Register Log In Moparts Forums Moparts Question and Answer PORTING 906 HEADS AROUND THE VALVES-SHROUDING

Print Thread

PORTING 906 HEADS AROUND THE VALVES-SHROUDING #1328579 10/30/12 12:14 PM 10/30/12 12:14 PM
Joined: Aug 2008 Posts: 48 Minnesota, USA M minnesota guy OP member
minnesota guy OP member M Joined: Aug 2008 Posts: 48 Minnesota, USA	DOES ANYONE HAVE FLOW BENCH NUMBERS FOR PORTING AROUND THE INTAKE AND EXHAUST VALVES ON A 906 HEAD OR THE LIKE, TO ELEVIATE SHROUDING? I AM REFERRING TO THOSE WITH 2.14, 2.18, 2.20 INTAKES AND 1.81 OR 1.88 EXHAUST VALVES. I AM THINKING THE NUMBERS COME IN AROUND 5 CFM OR SO?

Re: PORTING 906 HEADS AROUND THE VALVES-SHROUDING [Re: minnesota guy] #1328580 10/30/12 11:07 PM 10/30/12 11:07 PM
Joined: May 2008 Posts: 5,399 Aurora, Colorado 451Mopar master
451Mopar master Joined: May 2008 Posts: 5,399 Aurora, Colorado	Do you mean chamber shrouding? I don't have any info on that, sorry.

Re: PORTING 906 HEADS AROUND THE VALVES-SHROUDING [Re: minnesota guy] #1328581 10/31/12 03:01 PM 10/31/12 03:01 PM
Joined: Jan 2003 Posts: 1,908 Nebraska 4 4406bbl top fuel
4406bbl top fuel 4 Joined: Jan 2003 Posts: 1,908 Nebraska	Quote: DOES ANYONE HAVE FLOW BENCH NUMBERS FOR PORTING AROUND THE INTAKE AND EXHAUST VALVES ON A 906 HEAD OR THE LIKE, TO ELEVIATE SHROUDING? I AM REFERRING TO THOSE WITH 2.14, 2.18, 2.20 INTAKES AND 1.81 OR 1.88 EXHAUST VALVES. I AM THINKING THE NUMBERS COME IN AROUND 5 CFM OR SO? I do not know the exact figure, BUT if you do it do not unshroud all the way out to the head gasket. The smart way is to put the heads on a finish bored block, mark them left and right, then scratch a circle from the crank side on the head, unshroud and polish out to that line. If you use 1.88 and unshroud too much you may need to notch the bore, not a big deal but you need to check it, less is more sometimes, most like the 1.81, the whole block and head package fit is more important than a few cfm on a bench.

Re: PORTING 906 HEADS AROUND THE VALVES-SHROUDING [Re: 4406bbl] #1328582 11/01/12 12:02 PM 11/01/12 12:02 PM
Joined: Aug 2008 Posts: 48 Minnesota, USA M minnesota guy OP member
minnesota guy OP member M Joined: Aug 2008 Posts: 48 Minnesota, USA	I had to install 2.20 and 1.88 valves due to the seats and the heads prior useage. 20.00 swpa meet heads that had been running 2.18 and 1.81...I did some valve unshrouding clean up. Not excessive as I need to keep chambers as small as possible. I agree that you can outflow 2.20 1.88 valves with 2.14 and 1.81...the size becomes a factor and gets in the way of flow. Thanks.

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1