Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135412
12/16/11 07:04 PM
12/16/11 07:04 PM
|
Joined: May 2003
Posts: 15,487 Florida
scratchnfotraction
I Live Here
|
I Live Here
Joined: May 2003
Posts: 15,487
Florida
|
84 truck rotor or 76 new yorker rotors get the front will take an earlier rear axle,cant just swap them/change in c-clip c-body 8 3/4 is same as truck 8 1/4 or 9 1/4 the shackle flip with front hanger is good for 4-5 inches in the rear with axle floped on top of springs. can flip the front hanger also for another little bit. A-body 8 3/4 bolts in and tucks 12" rims with 29x15x15 M/Ts in the fenders like mine.(did both my stepside and wide box) 3/4 or 1 ton pocketed lower control arms with stock 1/2 ton spring or shorter for the front,get offset upper bushing to help alinement. very nice truck
Last edited by scratchnfotraction; 12/16/11 07:06 PM.
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: jerseybud]
#1135413
12/16/11 07:06 PM
12/16/11 07:06 PM
|
Joined: Aug 2011
Posts: 564 Round Rock,Tx
Nirvana
mopar
|
mopar
Joined: Aug 2011
Posts: 564
Round Rock,Tx
|
Saweet!!! That thing is awesome,im hoping to get my 87 looking that nice.I would buy the floor mats from you when you get rid of them. Jared
87 D100 225 4 speed.
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: Nirvana]
#1135416
12/16/11 07:10 PM
12/16/11 07:10 PM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
Quote:
Saweet!!! That thing is awesome,im hoping to get my 87 looking that nice.I would buy the floor mats from you when you get rid of them.
Jared
You can have them
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135417
12/16/11 07:11 PM
12/16/11 07:11 PM
|
Joined: May 2003
Posts: 15,487 Florida
scratchnfotraction
I Live Here
|
I Live Here
Joined: May 2003
Posts: 15,487
Florida
|
I run weld rims with 5 on 4.5 in my 88 440 truck some of the bigger newer rims do swap over IIRC the stock canyon sport rims are alum and have holes with a small cap,they look nice for stock I am sure after market has some bigger custom rims
Last edited by scratchnfotraction; 12/16/11 07:14 PM.
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135424
12/16/11 07:43 PM
12/16/11 07:43 PM
|
Joined: May 2003
Posts: 15,487 Florida
scratchnfotraction
I Live Here
|
I Live Here
Joined: May 2003
Posts: 15,487
Florida
|
mine is a daily driver with a stock 440 with 75.000 miles,built from a rust free Kansas truck with 58.000 miles on it,best condition seat i have ever saw till seeing yours yes they have plenty or after market rims and some of the other stock rims fit. my stepside has the 5 on 5.5 wagon spoke rims with the 85 center caps and trim rings. just check the axle register on the newer stock rims i dont care for any of the stock old or new myself
Last edited by scratchnfotraction; 12/16/11 07:45 PM.
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: Kevin I]
#1135425
12/16/11 07:43 PM
12/16/11 07:43 PM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
Quote:
I wish I could find something like that to drive so I can keep my trucks out of the weather. Is it pretty loaded up as far as options go?
AC !
And the upgraded seat and door panels, am/fm
They were still awful basic trucks in 1989
If anyone wants it more than me, I'll send'r down the road too
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: scratchnfotraction]
#1135430
12/16/11 07:51 PM
12/16/11 07:51 PM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
Quote:
does it have the steering box frame brace?
swaybar?
i bet it wont have the dodge truck driverside lean to it with that low milage and nice shape.
the back seems a tad high,but ihave seen one stock in a long time.
is it a TBI roller cam 318?
I'll have to look to see if it has brace, just got here
Yeah it has the stink bug stance, no lean to drivers side
Yep, thats the 1st year for it
Original brochure is laying in truck
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: ram87]
#1135432
12/16/11 08:34 PM
12/16/11 08:34 PM
|
Joined: Aug 2003
Posts: 12,291 Kent, Wa
340SHORTY
Truck Nut
|
Truck Nut
Joined: Aug 2003
Posts: 12,291
Kent, Wa
|
nice truck
there are a few nice 5.5 wheels out there. a lot more 4.5s.
the 81/84 rotors are a bolt on. the rears can be redrilled along with the drum.. a 4.5 drum will work but the center hole needs to be enlarged to fit the axle register..
I am truckless..
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135434
12/16/11 09:32 PM
12/16/11 09:32 PM
|
Joined: Jan 2003
Posts: 8,480 Candler,NC / Myrtle Beach, SC
JDMopar
master
|
master
Joined: Jan 2003
Posts: 8,480
Candler,NC / Myrtle Beach, SC
|
Quote:
What custom wheel choices are there , or do they all look like 4x4 wheels ?
Can I use wheels off a late model base Dodge van, the ones that are kinda like rally wheels ?
I think I know where I can get a set of those , IIRC they are 16's .. right ?
Nice truck! The wheels I think you're speaking of are the aluminum ones with the holes, right? If so, they are like the ones that were on our 92 Dodge perversion van. They are 15" wheels. Good luck with the truck.
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: JDMopar]
#1135435
12/16/11 09:39 PM
12/16/11 09:39 PM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
Quote:
Quote:
What custom wheel choices are there , or do they all look like 4x4 wheels ?
Can I use wheels off a late model base Dodge van, the ones that are kinda like rally wheels ?
I think I know where I can get a set of those , IIRC they are 16's .. right ?
Nice truck! The wheels I think you're speaking of are the aluminum ones with the holes, right? If so, they are like the ones that were on our 92 Dodge perversion van. They are 15" wheels. Good luck with the truck.
No, the ones I was thinking of look a lot alike the wheels you would see on a 76 Chrysler New Yorker
Its steel wheel , with a trim ring and a chrome center cap, they are steel, painted silver
My friend has these on his, they look pretty good too
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135441
12/16/11 10:18 PM
12/16/11 10:18 PM
|
Joined: May 2003
Posts: 15,487 Florida
scratchnfotraction
I Live Here
|
I Live Here
Joined: May 2003
Posts: 15,487
Florida
|
Quote:
Can you buy new rotors at Napa with the 4 1/2 pattern ?
yes ask for a 83-84 d-150 or 76 newyorker front rotors
they swap right on with the same wheel bearing
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: scratchnfotraction]
#1135442
12/16/11 10:24 PM
12/16/11 10:24 PM
|
Joined: Aug 2003
Posts: 12,291 Kent, Wa
340SHORTY
Truck Nut
|
Truck Nut
Joined: Aug 2003
Posts: 12,291
Kent, Wa
|
If you have the 9 1/4 rear,,, you CANNOT use the 84 and prior axle shafts in a 85 and later axle houseing..
I am truckless..
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: 340SHORTY]
#1135443
12/16/11 10:43 PM
12/16/11 10:43 PM
|
Joined: Oct 2005
Posts: 6,048 Back home in PA
BulletBob
master
|
master
Joined: Oct 2005
Posts: 6,048
Back home in PA
|
According to Auburn Differential the end of the axle changed after 1983. I had them on the phone this week after I got your PM about your hydra loc. Now I haven't dug out my Factory parts catalog yet but if what the guy at Auburn Differential is right then that means that an 84 axle will work. {I just double checked their catalog & the installation instructions too} According to them the change was after 1983.The 8.25 will interchange. The end of the axle never changed. Bigdad's truck having a 318 will most likely have a 8.25 Bob
Last edited by BulletBob; 12/16/11 10:59 PM.
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: BulletBob]
#1135444
12/16/11 10:56 PM
12/16/11 10:56 PM
|
Joined: Aug 2006
Posts: 8,064 Iowa
76dodgeboy
master
|
master
Joined: Aug 2006
Posts: 8,064
Iowa
|
Quote:
The rotors will fit from 84-down. You can use the 4.5 axles from 84-down if you have a 81/4 rear the carrier is the same for those from 1966-1996 [as per Auburn Differential] If you have a 91/4 84' model axles are the key to the swap [according to the Chrysler parts catalog] A true 3/4 ton [1/2"lugs] does not have a pocketed control arm Trucks with 9/16"-5/8" lugs have a pocketed control arm. All vans 78-98 with 1/2" studs have pockets & correct size balljoints. Dakota Drop spindles & a balljoint reamer for the steering arm work. You ream from the opposite side so the tierods don't have to be turned over. A 3" drop spring for a 94up Ram will get you 2". The rear is up to you
. 79-84 not anything older. Bearings changed from the info iv found. 81-84 2wd trucks/rc's are 5x4.5 4wds went to 5.5 in 80. Aint nothing hard about changing rotors or a rear axle so if you want 4.5 its easily obtained. Try looking at Summit Racing for rims in the 5.5bp. Your buddy had to modify those rims or he used spacers
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: BulletBob]
#1135445
12/16/11 11:03 PM
12/16/11 11:03 PM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
Quote:
Quote:
Ok...that's all I got in truck/van wheel knowledge! Right off hand, I'd say listen to Scratchinfotraction and forget the rest of us...lol. Well, maybe Mopar Jamie too.
Well, I guess the rest of us don't know anything & you're the judge! Can you disprove what I posted? I know that you can't. You're not only disrespectful to me but to everyone else who has posted a reply. This thread was made for a group of replies from more than just a select few of your choosing. W
Please , don't be upset with Jackie , we know each other and he is kinda messing with me
was not pointed at you, trust me
Sorry if you took it wrong ..
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: scratchnfotraction]
#1135446
12/16/11 11:05 PM
12/16/11 11:05 PM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
Quote:
Quote:
Can you buy new rotors at Napa with the 4 1/2 pattern ?
yes ask for a 83-84 d-150 or 76 newyorker front rotors
they swap right on with the same wheel bearing
I don't suppose you have PN#'S ??
Thanks for everyones help and suggestions too
And the nice words about the little blue truck too
Daryl
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: BulletBob]
#1135447
12/16/11 11:06 PM
12/16/11 11:06 PM
|
Joined: Aug 2003
Posts: 12,291 Kent, Wa
340SHORTY
Truck Nut
|
Truck Nut
Joined: Aug 2003
Posts: 12,291
Kent, Wa
|
ok we will say 84 from now on.. I had a 88 318/NP435 shorty. I thought that it had a 8 1/4, but was quite surprised to find it had a 9 1/4 under it. A check on the VIN proved it to be original.
I am truckless..
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: NITROUSN]
#1135451
12/16/11 11:28 PM
12/16/11 11:28 PM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
Ok, can I swap in a earler AKA "better" rear ? and achieve the 4 1/2 bolt pattern ?
Are those black, 4"+ mouldings on the lower body glued on or bolted on ?
I'd like to make it all dark blue , two tone does not ring my bell
I see no data sheet under the hood , guess Dodge ended that process in these years ?
And, the gear indicator does not work, sure its a cable piece, bet you can't get that anymore
is there a fix , or look in scrap yards ?
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135453
12/16/11 11:35 PM
12/16/11 11:35 PM
|
Joined: Oct 2005
Posts: 6,048 Back home in PA
BulletBob
master
|
master
Joined: Oct 2005
Posts: 6,048
Back home in PA
|
Quote:
Quote:
Quote:
Ok...that's all I got in truck/van wheel knowledge! Right off hand, I'd say listen to Scratchinfotraction and forget the rest of us...lol. Well, maybe Mopar Jamie too.
Well, I guess the rest of us don't know anything & you're the judge! Can you disprove what I posted? I know that you can't. You're not only disrespectful to me but to everyone else who has posted a reply. This thread was made for a group of replies from more than just a select few of your choosing. W
Please , don't be upset with Jackie , we know each other and he is kinda messing with me
was not pointed at you, trust me
Sorry if you took it wrong ..
Daryl, I'm sorry if I took it wrong. I love your truck, it's a great canvas. I can't wait to get my Shortbed home. Bob
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135455
12/16/11 11:38 PM
12/16/11 11:38 PM
|
Joined: Oct 2005
Posts: 6,048 Back home in PA
BulletBob
master
|
master
Joined: Oct 2005
Posts: 6,048
Back home in PA
|
If there's no sheet there's a plate under the cowl grille. Those mouldings have clips w/welded pins Bob
Last edited by BulletBob; 12/16/11 11:40 PM.
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: BulletBob]
#1135456
12/16/11 11:43 PM
12/16/11 11:43 PM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
Quote:
Daryl, I'm sorry if I took it wrong. I love your truck, it's a great canvas. I can't wait to get my Shortbed home. Bob
It is ok, I hope everyone thown in their
I want to do it right and not make a pile of junk so I like everyones imput
I sadly failed to follow this era well enough because I just never thought I COULD find one nice enough to own
I have found 100's of them but, always they have some kind of major issue .
I wanted a V8, auto, and a driver ..with no large body panel problems
I wanted a 83-84 but, they are getting just old enough any thing I FOUND was beat to death
I wanted a rubber mat , roll windows, no trim stocker in SILVER !!
Make a younger brother to the 70 !
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: NITROUSN]
#1135457
12/16/11 11:47 PM
12/16/11 11:47 PM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
Quote:
Hello Daryl. Yes the older 4.5 pattern stuff should swap in. I had 2 trucks this past summer i sent to the scrap yard with the parts you needed. I would of given then to you. Looks like a nice clean cruiser to me.
It is for sure, I'd like it to have a little attitude if possible
I hope to be able to find the right parts simple enough ( my, luck .. they are all gone now !
Silk purse out of sows ear
any suggestions will be taken to achieve that
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135459
12/17/11 12:08 AM
12/17/11 12:08 AM
|
Joined: Aug 2011
Posts: 564 Round Rock,Tx
Nirvana
mopar
|
mopar
Joined: Aug 2011
Posts: 564
Round Rock,Tx
|
Quote:
Quote:
Daryl, I'm sorry if I took it wrong. I love your truck, it's a great canvas. I can't wait to get my Shortbed home. Bob
It is ok, I hope everyone thown in their
I want to do it right and not make a pile of junk so I like everyones imput
I sadly failed to follow this era well enough because I just never thought I COULD find one nice enough to own
I have found 100's of them but, always they have some kind of major issue .
I wanted a V8, auto, and a driver ..with no large body panel problems
I wanted a 83-84 but, they are getting just old enough any thing I FOUND was beat to death
I wanted a rubber mat , roll windows, no trim stocker in SILVER !!
Make a younger brother to the 70 !
Wow
87 D100 225 4 speed.
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: BulletBob]
#1135461
12/17/11 12:25 AM
12/17/11 12:25 AM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
Quote:
I got lucky with my RC. It was parked in 89 or 90 with a bad engine. I paid $250.00 for it. After looking at hundreds with rust. Bob
Neighbor has one, super clean, never drives it
stock , red /white I've asked him to sell but,
NOPE !!
SLAMCHARGER !
I looked for those too, guess I'm a pickup man
http://www.youtube.com/watch?v=eGs-T5FNAyc
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135462
12/17/11 12:30 AM
12/17/11 12:30 AM
|
Joined: Aug 2003
Posts: 12,291 Kent, Wa
340SHORTY
Truck Nut
|
Truck Nut
Joined: Aug 2003
Posts: 12,291
Kent, Wa
|
YES... the 4.5 axles will interchange with your 5.5 axles. if you were closer I have a set of rotors and even a nice set of wheels that would fit. Id be interested in the fender and door mouldings.. the shortbox moulding wont work on my long box Dually..
I am truckless..
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: 340SHORTY]
#1135464
12/17/11 12:49 AM
12/17/11 12:49 AM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
Quote:
YES... the 4.5 axles will interchange with your 5.5 axles.
if you were closer I have a set of rotors and even a nice set of wheels that would fit. Id be interested in the fender and door mouldings.. the shortbox moulding wont work on my long box Dually..
I doubt I'll stip the moulding off if it leaves big holes to wled up underneath it
I'll have to see where we end up , body shop ,etc
I might even sell if before any of that happens
but, I'll look for more moulding in junk yards around here, they do show up at one yard often and if they do, the price is always fair
Thanks for all of your help & advice
stay tuned
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135465
12/17/11 12:53 AM
12/17/11 12:53 AM
|
Joined: Sep 2010
Posts: 718 Nunnelly, TN
Kevin I
super stock
|
super stock
Joined: Sep 2010
Posts: 718
Nunnelly, TN
|
Quote:
Quote:
Wow
Guess you never seen the 70 ??
That thing is awesome! If you want an older square body, I'll swap you.
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: Nirvana]
#1135466
12/17/11 12:53 AM
12/17/11 12:53 AM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
Quote:
Man that thing is gorgeous!
Thanks, yeah, its been in magazines I built that about 2004/05 I guess
It does not get out much, its a 440 and wins best of show anywhere / everywhere I take it
funny, the resto guys hate me
I am kinda trying to sell it and build something else
I doubt anyone will step up, but --never know
https://board.moparts.org/ubbthreads/show...e=0&fpart=1
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: Robbins]
#1135472
12/17/11 03:38 AM
12/17/11 03:38 AM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
I am that Pinkguy has not been here to talk to us I guess he is too good for us half ton'ers !
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135474
12/17/11 09:49 AM
12/17/11 09:49 AM
|
Joined: May 2003
Posts: 15,487 Florida
scratchnfotraction
I Live Here
|
I Live Here
Joined: May 2003
Posts: 15,487
Florida
|
new headlight bezels are fair price from rockauto and tail lights member thedodgeboys has stuff for them also,I got the full rubber set for mine Allen had one roll pan left and he has some of those euro tail lights for them too. the plastic piece for the trim are $$$$$$ when removed there are no holes per say but it will have a lot of the rivit/studs to be removed...in the lower corner of the cab,the trim piece does have a small hole were it bolts a clip to hold the trim on. i shaved it all off of mine. if the 8 3/8 10 bolt axle aka 8 1/4 does swap axles i have a set thats 5 on 4.5 if you want( is a complete rear axle 3.2? gear ) FYI.gear ratio will be stamped in the ring gear along with yr i will look around for part #s for the rotors,i have the ticket somewhere when i got mine from autozone...50$ each the gear indicater has a small box gizmo on the back of the gauge cluster that has a cable hook that hooks on a sloted arm on the colum. its the first thing to go most times and if someone droped the colum loose and did not un-hook it it stretches it out of wack. i will look at a few of the cluster I have and see if there is a good one if you need it if you pull the heater control..very gently as the switch likes to break off of the rack. I swaped all mine to 85 wire harness/colum and got rid of the turn sig dimmer and wiper stuff myself,it has problems when its beat to death...yours not so much probly.
Last edited by scratchnfotraction; 12/17/11 12:04 PM.
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: BulletBob]
#1135475
12/17/11 12:17 PM
12/17/11 12:17 PM
|
Joined: Jan 2003
Posts: 8,480 Candler,NC / Myrtle Beach, SC
JDMopar
master
|
master
Joined: Jan 2003
Posts: 8,480
Candler,NC / Myrtle Beach, SC
|
Quote:
Quote:
Quote:
Quote:
Ok...that's all I got in truck/van wheel knowledge! Right off hand, I'd say listen to Scratchinfotraction and forget the rest of us...lol. Well, maybe Mopar Jamie too.
Well, I guess the rest of us don't know anything & you're the judge! Can you disprove what I posted? I know that you can't. You're not only disrespectful to me but to everyone else who has posted a reply. This thread was made for a group of replies from more than just a select few of your choosing. W
Please , don't be upset with Jackie , we know each other and he is kinda messing with me
was not pointed at you, trust me
Sorry if you took it wrong ..
Daryl, I'm sorry if I took it wrong. I love your truck, it's a great canvas. I can't wait to get my Shortbed home. Bob
Bob....Daryl is right,and I was just being silly and messing with him. I'm quite sure that you, Scratchn, and plenty of others have forgotten more about trucks then I'll ever know. Sorry about the Wheaties....I'll be glad to send a new box.
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135479
12/17/11 10:38 PM
12/17/11 10:38 PM
|
Joined: Jan 2003
Posts: 4,576 Sarcoxie, MO, USA
MoPar Jamie
master
|
master
Joined: Jan 2003
Posts: 4,576
Sarcoxie, MO, USA
|
Very nice truck! Did someone say silver? Here is my '85 shorty. Original slant truck with OD 4, it now has a 318 in it with a cast OD-4 behind it. This was the motor and trans out of my '87 I wrecked. When the original 8 1/4 kicked up (not welded right) I decided to run an 8 3/4 with 5 on 4.5 bolt pattern to utilize my 15x8 stock steel wheels. Mine is from a '72-'74 truck. The axle is flipped and it decided to kick up on me today so I plan to get it welded soon. I have about 2 to 3 inches of clearance between housing and frame. On the front I am going to go with '81-'84 rotors so I can have matching bolt pattern. OK here is a pic. Dont get jealous because it is silver.
- MoPar Jamie
1972 Fury III 4dr 1986 D-150 LWB Royal SE
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135480
12/18/11 12:10 AM
12/18/11 12:10 AM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
Quote:
Anyone want / need the bug deflector ?
Or, its going in the trash
It has been claimed by a Moparts member
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: BulletBob]
#1135483
12/18/11 02:18 PM
12/18/11 02:18 PM
|
Joined: Aug 2006
Posts: 8,064 Iowa
76dodgeboy
master
|
master
Joined: Aug 2006
Posts: 8,064
Iowa
|
Quote:
The bearing diameter O.D. changed not the I.D. if I remember correctly I've always put an 83/4 in an not messed with either one anyway. I can't say that I'm right all the time for I am not a higher being. I don't claim to be & do not proclaim nor do I judge any of you. BOB
According to the bearing specs on Rockauto the inside diameter changed aswell
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135484
12/18/11 04:41 PM
12/18/11 04:41 PM
|
Joined: Jan 2008
Posts: 4,254 Canada
WO23Coronet
master
|
master
Joined: Jan 2008
Posts: 4,254
Canada
|
Quote:
What custom wheel choices are there , or do they all look like 4x4 wheels ?
Can I use wheels off a late model base Dodge van, the ones that are kinda like rally wheels ?
I think I know where I can get a set of those , IIRC they are 16's .. right ?
I know the rims you're talking about, I think they are the steel rims on the 94-01 1500's as well. To get those to work, your need to machine the center register from 3" to 3.5". Any machine shop with a lathe with at least a 16" swing could do it and it shouldn't be to much $ wise. I had an 89 shortbox that I put a set on and that's what I had to do. They fit great on the front but on the back they get really close to the box, I guess they have less offset that the stock 15" rims. I had 245/75/16 tires and they cleared by about 3/4", if I cornered to hard they would rub, not enough to do any damage to the tire or even hear or notice when you're driving but you could see it. with a low profile tire, you would have even more clearance and probably be fine.
As for aftermarket rims, there should be a ton, as the late 60's to 96 Ford half tons had the same bolt pattern and the same 3.5" center register. There seems to be no shortage of aftermarket rims on those things.
And just to clarify, what exactly changed on the 81-84 rotors? Is it just the machined diameter on the inside of the rotor where the bearing race presses into?
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135486
12/18/11 10:57 PM
12/18/11 10:57 PM
|
Joined: Aug 2003
Posts: 12,291 Kent, Wa
340SHORTY
Truck Nut
|
Truck Nut
Joined: Aug 2003
Posts: 12,291
Kent, Wa
|
And just to clarify, what exactly changed on the 81-84 rotors? Is it just the machined diameter on the inside of the rotor where the bearing race presses into?
the hubs on the 5.5 rotors use a larger diameter inner bearing.
I am truckless..
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135487
12/20/11 01:30 AM
12/20/11 01:30 AM
|
Joined: Jan 2008
Posts: 4,254 Canada
WO23Coronet
master
|
master
Joined: Jan 2008
Posts: 4,254
Canada
|
Quote:
Uhhhh .. as far as I know, they were only on just the vans ?
My brother has a old retired work van and it had them so I called him to see if they could be had
He put them on his 91 4x4 Dodge
so, I guess that means they fit ?
Maybe after Christmas I go digging around a junk yard to look for a set
I took the little guy for about a 75 mile road trip today, it just truely is a sweet little truck
Well, I guess the vans are different that the 1500's, that's what I had to do to put 94-01 rims on my 89
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: WO23Coronet]
#1135488
12/20/11 02:47 AM
12/20/11 02:47 AM
|
Joined: Aug 2006
Posts: 8,064 Iowa
76dodgeboy
master
|
master
Joined: Aug 2006
Posts: 8,064
Iowa
|
Quote:
Quote:
Uhhhh .. as far as I know, they were only on just the vans ?
My brother has a old retired work van and it had them so I called him to see if they could be had
He put them on his 91 4x4 Dodge
so, I guess that means they fit ?
Maybe after Christmas I go digging around a junk yard to look for a set
I took the little guy for about a 75 mile road trip today, it just truely is a sweet little truck
Well, I guess the vans are different that the 1500's, that's what I had to do to put 94-01 rims on my 89
Vans still had the larger hub so the van wheels Will fit the pre 94 trucks without a problem. They also use the same control arm till 97 or so. My cousin had a 96 or so shorty van and my mom had some 94 up 1500 rims for sale and when we went to put them on to see how they looked they wouldnt clear the hub. I dont think it matters if he finds wheels its already listed forsale
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: 76dodgeboy]
#1135491
12/20/11 03:16 AM
12/20/11 03:16 AM
|
Joined: Aug 2006
Posts: 8,064 Iowa
76dodgeboy
master
|
master
Joined: Aug 2006
Posts: 8,064
Iowa
|
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: 76dodgeboy]
#1135492
12/20/11 03:20 AM
12/20/11 03:20 AM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
Quote:
Pretty sure he means these
closer but, I have seen them with chrome rings and center caps
I'll see if I can locate any
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: 76dodgeboy]
#1135493
12/20/11 03:21 AM
12/20/11 03:21 AM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
Quote:
The lowered version
Don't think I'll drop it down that far
Just enough to have the tire opening and tire top meet
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: BulletBob]
#1135495
12/20/11 03:36 AM
12/20/11 03:36 AM
|
Joined: Aug 2003
Posts: 12,291 Kent, Wa
340SHORTY
Truck Nut
|
Truck Nut
Joined: Aug 2003
Posts: 12,291
Kent, Wa
|
I agree,, the 8 1/4/8 3/8 axle shafts will interchange.
My 88 was a 318 NP435 shorty. I thought it had a 8 1/4 till I had a counter clown buddy at a dealer run the numbers. It came out to be a factory original equiped 9 1/4. That 9 1/4 diff that I have was going into my 87 RC till it met its demise.
I am truckless..
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135496
12/20/11 04:29 AM
12/20/11 04:29 AM
|
Joined: May 2009
Posts: 461 Hinterland SE Qld Aust
SG duster
mopar
|
mopar
Joined: May 2009
Posts: 461
Hinterland SE Qld Aust
|
Quote:
I have searched for a Squarebody Dodge 81-93 Shortbox for years , it had to be nice..
This one is really, really original and CLEAN !
thats a cool ute
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: hp383]
#1135499
12/20/11 11:47 PM
12/20/11 11:47 PM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
Quote:
Quote:
Quote:
Pretty sure he means these
closer but, I have seen them with chrome rings and center caps
I'll see if I can locate any
Are you thinking about Chrysler road wheels
Yep, they made on 1500 series trucks and light duty vans, wheels that look a lot like that but they are 5 on 5 1/2 bolt pattern and the center cap has a goat head on it
I seen a 96ish truck today with a set but, couldn't catch him to take a pic
here is what I did catch
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: hp383]
#1135500
12/20/11 11:49 PM
12/20/11 11:49 PM
|
Joined: Aug 2003
Posts: 12,291 Kent, Wa
340SHORTY
Truck Nut
|
Truck Nut
Joined: Aug 2003
Posts: 12,291
Kent, Wa
|
ROTORS Raybestos #7034 Bendix #1072 BEARINGS BR 16 Outers BR 17 Inners
I am truckless..
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: 340SHORTY]
#1135501
12/21/11 12:24 AM
12/21/11 12:24 AM
|
Joined: Nov 2004
Posts: 6,653 Near Reading PA USA
pinkduster
master
|
master
Joined: Nov 2004
Posts: 6,653
Near Reading PA USA
|
That's a nice little truck. I'd love to build something like that too. Slammed, no moldings, 70s front bumper, pan in the rear, 91-93 grille, monotone, cowl hood and some Weld Wheels. There is one for sale around here. Think it's an 84, already has a 440 in it. Could probably get it for around 2k and it's pretty decent. Just have to keep telling myself, NO MORE VEHICLES right now.
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: 76dodgeboy]
#1135507
12/21/11 09:52 AM
12/21/11 09:52 AM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
Quote:
I found this pic but I'll measure the center with pics tomorrow of mine
My brother put them on his 91 ?
I'll ask him, but, those are the stock rims I like
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135510
12/21/11 11:58 AM
12/21/11 11:58 AM
|
Joined: May 2003
Posts: 15,487 Florida
scratchnfotraction
I Live Here
|
I Live Here
Joined: May 2003
Posts: 15,487
Florida
|
Quote:
I can get these in 5 on 5 1/2
What do you think they look like ?
they have polished too
http://www.radirwheels.com/wheels.htm
i would love to have a set of those on my 85 stepside,I think the cast ones look good myself,not so much the polished ones.
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135516
12/22/11 05:04 PM
12/22/11 05:04 PM
|
Joined: Jan 2008
Posts: 4,254 Canada
WO23Coronet
master
|
master
Joined: Jan 2008
Posts: 4,254
Canada
|
Quote:
Quote:
I found this pic but I'll measure the center with pics tomorrow of mine
My brother put them on his 91 ?
I'll ask him, but, those are the stock rims I like
Those are the rims I was talking about in my earlier post. YOU WILL have to enlarge the center from 3" to 3.5" if you get them off a 1500, unless, like mentioned earlier by another member (76dodgeboy I think), you get a set off a B250 van, those apparently have the larger hub hole. Any compotent machine shop can bore those out, either by lathe (probable method) or by mill with a rotary table
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: BulletBob]
#1135517
12/23/11 07:26 PM
12/23/11 07:26 PM
|
Joined: Aug 2003
Posts: 4,974 new jersey usa
11secdart
master
|
master
Joined: Aug 2003
Posts: 4,974
new jersey usa
|
Nice truck, reminds me of the late 80s D100 2WD, Short bed ,6 cyl. I had awhile back. I have the same wheels as the van in the other post but with a smooth snap in center cap. they came off my friends 90 2WD Ramcharger. They are 15 inch, 5.5 bolt pattern, they look good on my 92 D150 and I haven`t seen them on too many other trucks,vans etc.
68 Dart 410 / 904 92 D150 original owner 21 Ram 1500 Quad Cab, Big Horn , Hemi ,4x4 23 Audi Q5 16 Honda HRV
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135520
12/23/11 09:24 PM
12/23/11 09:24 PM
|
Joined: May 2003
Posts: 15,487 Florida
scratchnfotraction
I Live Here
|
I Live Here
Joined: May 2003
Posts: 15,487
Florida
|
Quote:
Quote:
Heres mine
Looks great !!
those are the best I have seen on a mid 80s truck,well done
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135525
12/27/11 03:45 PM
12/27/11 03:45 PM
|
Joined: Oct 2005
Posts: 6,048 Back home in PA
BulletBob
master
|
master
Joined: Oct 2005
Posts: 6,048
Back home in PA
|
Quote:
mounted on a friends binder
Does your friend want a CrewCab Binder like that? The guy has a factory built IH limo also for sale. The CrewCab is a unibody. Those wheels are cool I'm sure what ever else you do to it will be tasteful like the wheels.
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: 1964Polara]
#1135531
12/30/11 01:29 PM
12/30/11 01:29 PM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
Quote:
What price are you looking at for Radir Wheels Satin? I like the oldschool look..... Love also the Cragar Bonneville's Cast
I'm just trying to find something in 5 on 5 1/2 that does not look like a 4x4 wheel
The guy paid a lot for the Radirs, $1380.00 for the set in 15x6 and 15x8's
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135533
04/16/13 11:16 PM
04/16/13 11:16 PM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
If the weather EVER lets up, I'm going to get back on this heap wanted to bump it so I could re-read the info I will be back to asking questions again
The lips of fools bring them strife, and their mouths invite a beating.Proverbs 18:6
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135534
04/16/13 11:18 PM
04/16/13 11:18 PM
|
Joined: Feb 2004
Posts: 34,871 S.E. South Dakota !
bigdad
OP
Still Posting A Lot
|
OP
Still Posting A Lot
Joined: Feb 2004
Posts: 34,871
S.E. South Dakota !
|
found a set of these
doubt I'll use them
The lips of fools bring them strife, and their mouths invite a beating.Proverbs 18:6
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135539
04/17/13 12:02 AM
04/17/13 12:02 AM
|
Joined: Apr 2004
Posts: 1,093 It's beer:30 somewhere
adventurer
super stock
|
super stock
Joined: Apr 2004
Posts: 1,093
It's beer:30 somewhere
|
Thats 8.25, just do the axle swap.
Last edited by adventurer; 04/17/13 12:04 AM.
77 Dodge Adventurer SE 440 2wd SWB 78 Dodge Adventurer SE 440 2wd Utiline 90 Dodge D150 SWB 2wd 318fi 4speed 60 Desoto Adventurer 2dr 67 Dodge Dart Gt Conv. 273 4bbl 04 PT Cruiser GT Turbo 14 Ram R/T "Life's to short to drink cheap beer."
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135542
04/17/13 09:07 AM
04/17/13 09:07 AM
|
Joined: Jul 2006
Posts: 9,366 Lehigh Acres, Florida
rickstershemi
master
|
master
Joined: Jul 2006
Posts: 9,366
Lehigh Acres, Florida
|
Quote:
I have a PM from a member that has axles
with 4 1/2 BP and parts
bsd idea ?
I have never dicked with this rear diff
I have a suregrip for an 8.25 that I won't be using...????
Rickster
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: basketcase]
#1135545
05/04/14 02:35 PM
05/04/14 02:35 PM
|
Joined: Mar 2007
Posts: 4,130 Halifax, N.S. Canada
Edison62
master
|
master
Joined: Mar 2007
Posts: 4,130
Halifax, N.S. Canada
|
Nice truck.....any updates?
Lots of good info posted also....
Bryan.
Don't be stupid.... it's not smart!
1970 Super Bee. Big blk 4 speed car. 1973 Dodge Dart Sport 340 4 speed car. 1985 Dodge Ram D-100 /6 auto. Original paint 1990 Dodge Ram D-150 V-6 5 Speed. Original paint 1995 Chrysler LHS V-6 auto. Original paint 2014 Ram 1500 R/T 5.7 Hemi...!
|
|
|
Re: My new ( to me ) 1989 Dodge D-100 shortbox !
[Re: bigdad]
#1135547
05/05/14 12:23 AM
05/05/14 12:23 AM
|
Joined: Mar 2007
Posts: 4,130 Halifax, N.S. Canada
Edison62
master
|
master
Joined: Mar 2007
Posts: 4,130
Halifax, N.S. Canada
|
Daryl, I really like your truck, great color combo! I bought this one out of Reno....36,000 original miles and super clean!
Bryan.
Don't be stupid.... it's not smart!
1970 Super Bee. Big blk 4 speed car. 1973 Dodge Dart Sport 340 4 speed car. 1985 Dodge Ram D-100 /6 auto. Original paint 1990 Dodge Ram D-150 V-6 5 Speed. Original paint 1995 Chrysler LHS V-6 auto. Original paint 2014 Ram 1500 R/T 5.7 Hemi...!
|
|
|
|
|