Previous Thread
Next Thread
Print Thread
Page 2 of 2 1 2
Re: 8-3/4 rear end selection question [Re: DoctorDiff] #1078646
09/21/11 02:01 PM
09/21/11 02:01 PM
Joined: Dec 2005
Posts: 4,258
State of Fascism
5
52savoy Offline
master
52savoy  Offline
master
5

Joined: Dec 2005
Posts: 4,258
State of Fascism
You talk'n to me???

I got my specs directly from Chrysler...
The only B-body housing that was shorter was the Max wedge..1/2"

Last edited by 52savoy; 09/21/11 02:03 PM.
Re: 8-3/4 rear end selection question [Re: DoctorDiff] #1078647
09/21/11 02:02 PM
09/21/11 02:02 PM
Joined: Sep 2011
Posts: 339
California
M
moparbroz Offline OP
enthusiast
moparbroz  Offline OP
enthusiast
M

Joined: Sep 2011
Posts: 339
California
I will have to adjust to install. I have all the measurements thanks to you guys.


Hebrews 11:1
Re: 8-3/4 rear end selection question [Re: DoctorDiff] #1078648
09/21/11 02:05 PM
09/21/11 02:05 PM
Joined: Sep 2011
Posts: 339
California
M
moparbroz Offline OP
enthusiast
moparbroz  Offline OP
enthusiast
M

Joined: Sep 2011
Posts: 339
California
Thanks for the measurements. I found them also in the tech archive. 3.3" adjustment based on center of the perchs. Thanks!


Hebrews 11:1
Re: 8-3/4 rear end selection question [Re: DoctorDiff] #1078649
09/21/11 02:08 PM
09/21/11 02:08 PM
Joined: Sep 2011
Posts: 339
California
M
moparbroz Offline OP
enthusiast
moparbroz  Offline OP
enthusiast
M

Joined: Sep 2011
Posts: 339
California
"Dr. Diff." I want that offset! Send me the info including shipping to 92867 and payment preferene to moparbros@yahoo.com. Thanks!


Hebrews 11:1
Re: 8-3/4 rear end selection question [Re: 52savoy] #1078650
09/21/11 02:09 PM
09/21/11 02:09 PM
Joined: Jan 2003
Posts: 8,016
Polson, MT
DoctorDiff Offline
master
DoctorDiff  Offline
master

Joined: Jan 2003
Posts: 8,016
Polson, MT
The information you got from Chrysler is incorrect.

In addition...

'63 B-body housing: 53 1/4" with 44" perch on center
'64 B-body housing: 55 5/8"" with 44" perch on center (except max wedge)
'71-'73 B-body wagon housing: 59 7/16" with 47.3" perch on center

Re: 8-3/4 rear end selection question [Re: DoctorDiff] #1078651
09/21/11 02:15 PM
09/21/11 02:15 PM
Joined: Dec 2005
Posts: 4,258
State of Fascism
5
52savoy Offline
master
52savoy  Offline
master
5

Joined: Dec 2005
Posts: 4,258
State of Fascism
The information from Chrysler is the "track" measurement. Yours is axle housing length.

correct?

Re: 8-3/4 rear end selection question *DELETED* [Re: 52savoy] #1078652
09/21/11 02:23 PM
09/21/11 02:23 PM
Joined: Jan 2003
Posts: 25,200
Upper Midwest
M
MoparforLife Offline
Too Many Posts
MoparforLife  Offline
Too Many Posts
M

Joined: Jan 2003
Posts: 25,200
Upper Midwest
Post deleted by MoparforLife

Re: 8-3/4 rear end selection question [Re: moparbroz] #1078653
09/21/11 02:45 PM
09/21/11 02:45 PM
Joined: Jan 2003
Posts: 8,016
Polson, MT
DoctorDiff Offline
master
DoctorDiff  Offline
master

Joined: Jan 2003
Posts: 8,016
Polson, MT
E-mail sent.

Thanks,

Cass

Re: 8-3/4 rear end selection question [Re: DoctorDiff] #1078654
09/21/11 02:46 PM
09/21/11 02:46 PM
Joined: Jan 2003
Posts: 16,376
D
dogdays Offline
I Live Here
dogdays  Offline
I Live Here
D

Joined: Jan 2003
Posts: 16,376
I just talked to Bil Abel at Western Drivetrain and he said the Yukon Powr-Loks were still on backorder, this makes nearly two years. But, he did get a TrueTrac in the other day.

He also warned me that Randy's had a batch made this year and rejected them all because of material problems. So if you see a new Powr-Lok on the 'bay or other places, it is probably the Randy's reject and you don't want it. Machining problems may be repairable but material problems aren't usually.

R.

Re: 8-3/4 rear end selection question [Re: 52savoy] #1078655
09/21/11 02:51 PM
09/21/11 02:51 PM
Joined: Jan 2003
Posts: 8,016
Polson, MT
DoctorDiff Offline
master
DoctorDiff  Offline
master

Joined: Jan 2003
Posts: 8,016
Polson, MT
"Track measurement" varies with housing width.

Re: 8-3/4 rear end selection question [Re: MoparforLife] #1078656
09/21/11 03:02 PM
09/21/11 03:02 PM
Joined: Jan 2003
Posts: 8,016
Polson, MT
DoctorDiff Offline
master
DoctorDiff  Offline
master

Joined: Jan 2003
Posts: 8,016
Polson, MT
My offset hanger/shackle kit bolts in place of the stock brackets. You do not have to modify the new hangers or the body.

In this application, you can't just "move the spring perch" because the U-bolts would end up on top of the housing end.

Re: 8-3/4 rear end selection question [Re: DoctorDiff] #1078657
09/21/11 03:18 PM
09/21/11 03:18 PM
Joined: Jan 2003
Posts: 25,200
Upper Midwest
M
MoparforLife Offline
Too Many Posts
MoparforLife  Offline
Too Many Posts
M

Joined: Jan 2003
Posts: 25,200
Upper Midwest
68 C body is very close to a bolt in. In fact many have done it by just tweaking the springs slightly. That is what I used on 75 Cordoba and just modified the perch slightly.
Sorry Doc, You are right I was going the wrong direction on previous post. (Deleted.)

Re: 8-3/4 rear end selection question [Re: moparbroz] #1078658
09/21/11 04:24 PM
09/21/11 04:24 PM
Joined: Mar 2005
Posts: 2,060
Pendleton NY
T
terzmo Offline
top fuel
terzmo  Offline
top fuel
T

Joined: Mar 2005
Posts: 2,060
Pendleton NY
go here and it should answer most,if not all, questions

http://bionicdodge.com/Download/Mopar_8_3_4_Rear_End_Guide.PDF

Re: 8-3/4 rear end selection question [Re: terzmo] #1078659
09/21/11 05:46 PM
09/21/11 05:46 PM
Joined: Sep 2011
Posts: 339
California
M
moparbroz Offline OP
enthusiast
moparbroz  Offline OP
enthusiast
M

Joined: Sep 2011
Posts: 339
California
Awesome resource. Thanks!


Hebrews 11:1
Re: 8-3/4 rear end selection question [Re: moparbroz] #1078660
09/21/11 06:24 PM
09/21/11 06:24 PM
Joined: Jan 2003
Posts: 8,016
Polson, MT
DoctorDiff Offline
master
DoctorDiff  Offline
master

Joined: Jan 2003
Posts: 8,016
Polson, MT
I also stock custom and standard length 30 and 35 spline high-strength axle packages for most 8 3/4" and Dana 60 applications.

Re: 8-3/4 rear end selection question [Re: DoctorDiff] #1078661
09/21/11 06:55 PM
09/21/11 06:55 PM
Joined: Sep 2011
Posts: 339
California
M
moparbroz Offline OP
enthusiast
moparbroz  Offline OP
enthusiast
M

Joined: Sep 2011
Posts: 339
California
Cass- I will probably need more than just the hanger and shackle kit from you. Can you email be a parts explosion of an 8-3/4 housing, axel and suregrip unit so I can dtermine what I will need? Thanks!


Hebrews 11:1
Re: 8-3/4 rear end selection question [Re: moparbroz] #1078662
09/24/11 11:39 PM
09/24/11 11:39 PM
Joined: Jan 2007
Posts: 389
kansas city, mo
rave_12000 Offline
enthusiast
rave_12000  Offline
enthusiast

Joined: Jan 2007
Posts: 389
kansas city, mo
why do you need to change axles?? looks like correct ones are still in the housing. use a needle grease gun tip to pack the outer axle bearings. i think i have an extra carrier out in the garage.

Re: 8-3/4 rear end selection question [Re: terzmo] #1078663
09/25/11 12:45 AM
09/25/11 12:45 AM
Joined: Apr 2005
Posts: 12,271
Overpriced Housing Central
RobX4406 Offline
I Live Here
RobX4406  Offline
I Live Here

Joined: Apr 2005
Posts: 12,271
Overpriced Housing Central
Quote:

go here and it should answer most,if not all, questions

http://bionicdodge.com/Download/Mopar_8_3_4_Rear_End_Guide.PDF




That has some REALLY bad info because people don't understand track width versus actual axle width. Track width on all 62-70 B's is not 59.2...

Want a better reference, it's here in the tech archive...

http://www.moparts.org/Tech/Archive/axle/16.html

Re: 8-3/4 rear end selection question [Re: RobX4406] #1078664
09/25/11 12:58 PM
09/25/11 12:58 PM
Joined: Nov 2004
Posts: 2,825
Sk. Canada
RemCharger Offline
master
RemCharger  Offline
master

Joined: Nov 2004
Posts: 2,825
Sk. Canada
I believe the 70-71, 72? c body is a nice direct bolt in. A buddy just put one in a 74 charger.

That 69 rearend appeared to have axles in it...

Page 2 of 2 1 2






Powered by UBB.threads™ PHP Forum Software 7.7.1