drill size for priming engine

Print Thread

Re: drill size for priming engine [Re: rftroy] #1749849 02/11/15 11:12 PM 02/11/15 11:12 PM
Joined: Nov 2003 Posts: 36,040 Lincoln Nebraska R RapidRobert Circle Track
RapidRobert Circle Track R Joined: Nov 2003 Posts: 36,040 Lincoln Nebraska	You might loosen the pump mounting bolts slightly then insert the intergear shaft then retighten the pump bolts. That solves a slight binding with SB's so I would assume it might be beneficial on a BB live every 24 hour block of time like it's your last day on earth

Entire Thread
Subject	Posted By	Posted
drill size for priming engine	ryanf	02/09/15 05:22 AM
Re: drill size for priming engine	NITROUSN	02/09/15 05:24 AM
Re: drill size for priming engine	ryanf	02/09/15 05:30 AM
Re: drill size for priming engine	NITROUSN	02/09/15 05:34 AM
Re: drill size for priming engine	ryanf	02/09/15 05:37 AM
Re: drill size for priming engine	Supercuda	02/09/15 05:48 AM
Re: drill size for priming engine	ryanf	02/09/15 05:56 AM
Re: drill size for priming engine	Supercuda	02/09/15 06:00 AM
Re: drill size for priming engine	E-Ticket	02/09/15 06:03 AM
Re: drill size for priming engine	Cab_Burge	02/09/15 06:35 AM
Re: drill size for priming engine	71rm23	02/10/15 08:44 PM
Re: drill size for priming engine	mikemee1331	02/10/15 09:42 PM
Re: drill size for priming engine	RapidRobert	02/10/15 11:31 PM
Re: drill size for priming engine	dogdays	02/11/15 12:41 AM
Re: drill size for priming engine	sportfury70	02/11/15 01:47 AM
Re: drill size for priming engine	DDodger	02/12/15 09:32 PM
Re: drill size for priming engine	440W8 Duster	02/09/15 05:24 AM
Re: drill size for priming engine	cudatom	02/09/15 05:27 AM
Re: drill size for priming engine	RapidRobert	02/09/15 05:29 AM
Re: drill size for priming engine	gtx6970	02/09/15 05:36 AM
Re: drill size for priming engine	AndyF	02/10/15 10:03 PM
Re: drill size for priming engine	gdonovan	02/11/15 03:02 AM
Re: drill size for priming engine	skicker	02/11/15 03:36 AM
Re: drill size for priming engine	LaRoy Engines	02/11/15 04:11 PM
Re: drill size for priming engine	70AARcuda	02/11/15 04:16 PM
Re: drill size for priming engine	HPMike	02/11/15 04:27 PM
Re: drill size for priming engine	SportF	02/11/15 09:34 PM
Re: drill size for priming engine	383man	02/13/15 02:44 AM
Re: drill size for priming engine	Twostick	02/11/15 09:35 PM
Re: drill size for priming engine	ryanf	02/11/15 11:28 PM
Re: drill size for priming engine	rftroy	02/11/15 11:48 PM
Re: drill size for priming engine	RapidRobert	02/12/15 03:12 AM

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To