drill size for priming engine

Print Thread

Re: drill size for priming engine [Re: ryanf] #1749827 02/09/15 01:36 AM 02/09/15 01:36 AM
Joined: Jun 2003 Posts: 21,382 It's a dry heat gtx6970 Too Many Posts
gtx6970 Too Many Posts Joined: Jun 2003 Posts: 21,382 It's a dry heat	1/2" Milwaukee , Use it with any engine oil from 5w-20 to 15w-40,,never had a problem yet Start the drill ( 1st ) and spin the engine by hand. Once I have oil getting to the top ,,I'll spin it with the starter with no plugs in it and no gas in the carb. Put everything in and fire it up with no worries

Entire Thread
Subject	Posted By	Posted
drill size for priming engine	ryanf	02/09/15 05:22 AM
Re: drill size for priming engine	NITROUSN	02/09/15 05:24 AM
Re: drill size for priming engine	ryanf	02/09/15 05:30 AM
Re: drill size for priming engine	NITROUSN	02/09/15 05:34 AM
Re: drill size for priming engine	ryanf	02/09/15 05:37 AM
Re: drill size for priming engine	Supercuda	02/09/15 05:48 AM
Re: drill size for priming engine	ryanf	02/09/15 05:56 AM
Re: drill size for priming engine	Supercuda	02/09/15 06:00 AM
Re: drill size for priming engine	E-Ticket	02/09/15 06:03 AM
Re: drill size for priming engine	Cab_Burge	02/09/15 06:35 AM
Re: drill size for priming engine	71rm23	02/10/15 08:44 PM
Re: drill size for priming engine	mikemee1331	02/10/15 09:42 PM
Re: drill size for priming engine	RapidRobert	02/10/15 11:31 PM
Re: drill size for priming engine	dogdays	02/11/15 12:41 AM
Re: drill size for priming engine	sportfury70	02/11/15 01:47 AM
Re: drill size for priming engine	DDodger	02/12/15 09:32 PM
Re: drill size for priming engine	440W8 Duster	02/09/15 05:24 AM
Re: drill size for priming engine	cudatom	02/09/15 05:27 AM
Re: drill size for priming engine	RapidRobert	02/09/15 05:29 AM
Re: drill size for priming engine	gtx6970	02/09/15 05:36 AM
Re: drill size for priming engine	AndyF	02/10/15 10:03 PM
Re: drill size for priming engine	gdonovan	02/11/15 03:02 AM
Re: drill size for priming engine	skicker	02/11/15 03:36 AM
Re: drill size for priming engine	LaRoy Engines	02/11/15 04:11 PM
Re: drill size for priming engine	70AARcuda	02/11/15 04:16 PM
Re: drill size for priming engine	HPMike	02/11/15 04:27 PM
Re: drill size for priming engine	SportF	02/11/15 09:34 PM
Re: drill size for priming engine	383man	02/13/15 02:44 AM
Re: drill size for priming engine	Twostick	02/11/15 09:35 PM
Re: drill size for priming engine	ryanf	02/11/15 11:28 PM
Re: drill size for priming engine	rftroy	02/11/15 11:48 PM
Re: drill size for priming engine	RapidRobert	02/12/15 03:12 AM

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To