Is .002" rod bearing clearance to tight ?

Print Thread

Re: Is .002" rod bearing clearance to tight ? [Re: Cab_Burge] #1222471 04/27/12 12:13 AM 04/27/12 12:13 AM
Joined: Feb 2006 Posts: 146 Wis. R rlm2268 OP member
rlm2268 OP member R Joined: Feb 2006 Posts: 146 Wis.	Yes rods were torqued when measured, short block is acually assembled and ran into a side clearance issue on 7 and 8 rod, figured that out the bearing must have been slightly touching the crank fillet, scraped the bearing a little on the chamfer side and now the side clearance is the same as the rest but now having second thoughts about the bearing clearance.

Entire Thread
Subject	Posted By	Posted
Is .002" rod bearing clearance to tight ?	rlm2268	04/26/12 06:32 AM
Re: Is .002" rod bearing clearance to tight ?	cudabin	04/26/12 06:40 AM
Re: Is .002" rod bearing clearance to tight ?	Twin Turbo Mower	04/26/12 08:24 AM
Re: Is .002" rod bearing clearance to tight ?	MR_P_BODY	04/26/12 01:44 PM
Re: Is .002" rod bearing clearance to tight ?	Moparnut426	04/26/12 01:49 PM
Re: Is .002" rod bearing clearance to tight ?	rlm2268	04/26/12 01:54 PM
Re: Is .002" rod bearing clearance to tight ?	MR_P_BODY	04/26/12 02:00 PM
Re: Is .002" rod bearing clearance to tight ?	rickseeman	04/26/12 02:09 PM
Re: Is .002" rod bearing clearance to tight ?	maximum entropy	04/26/12 04:04 PM
Re: Is .002" rod bearing clearance to tight ?	DJVCuda	04/26/12 02:23 PM
Re: Is .002" rod bearing clearance to tight ?	BradH	04/26/12 04:54 PM
Re: Is .002" rod bearing clearance to tight ?	66er	04/26/12 05:05 PM
Re: Is .002" rod bearing clearance to tight ?	Cab_Burge	04/26/12 05:17 PM
Re: Is .002" rod bearing clearance to tight ?	66er	04/26/12 05:25 PM
Re: Is .002" rod bearing clearance to tight ?	rlm2268	04/27/12 02:52 AM
Re: Is .002" rod bearing clearance to tight ?	Cab_Burge	04/27/12 03:57 AM
Re: Is .002" rod bearing clearance to tight ?	rlm2268	04/27/12 04:13 AM
Re: Is .002" rod bearing clearance to tight ?	66er	04/27/12 03:48 PM
Re: Is .002" rod bearing clearance to tight ?	rlm2268	04/27/12 05:02 PM
Re: Is .002" rod bearing clearance to tight ?	8urvette	04/27/12 05:17 PM
Re: Is .002" rod bearing clearance to tight ?	cudatom	02/22/19 06:25 PM
Re: Is .002" rod bearing clearance to tight ?	BradH	04/27/12 03:26 PM
Re: Is .002" rod bearing clearance to tight ?	gregsdart	02/21/19 07:21 PM
Re: Is .002" rod bearing clearance to tight ?	CMcAllister	02/21/19 07:33 PM
Re: Is .002" rod bearing clearance to tight ?	lewtot184	02/21/19 07:46 PM
Re: Is .002" rod bearing clearance to tight ?	Cab_Burge	02/22/19 02:35 AM
Re: Is .002" rod bearing clearance to tight ?	dvw	02/21/19 09:19 PM
Re: Is .002" rod bearing clearance to tight ?	dthemi	02/22/19 01:52 AM
Re: Is .002" rod bearing clearance to tight ?	BobR	02/22/19 10:14 PM
Re: Is .002" rod bearing clearance to tight ?	merpar	02/22/19 02:56 AM
Re: Is .002" rod bearing clearance to tight ?	moparx	02/22/19 06:19 PM
Re: Is .002" rod bearing clearance to tight ?	451Mopar	02/22/19 06:53 AM
Re: Is .002" rod bearing clearance to tight ?	fastmark	02/22/19 03:11 PM
Re: Is .002" rod bearing clearance to tight ?	polyspheric	02/22/19 04:01 PM
Re: Is .002" rod bearing clearance to tight ?	CMcAllister	02/22/19 07:45 PM
Re: Is .002" rod bearing clearance to tight ?	Cab_Burge	02/22/19 10:09 PM
Re: Is .002" rod bearing clearance to tight ?	mopar dave	02/23/19 05:03 AM
Re: Is .002" rod bearing clearance to tight ?	polyspheric	02/23/19 05:11 AM

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To