Posted By: DemonDust
Easy 904 question - 11/12/11 12:54 AM
On the front drum with 5 thin discs, what is the minimum clearance? I'm thinking .060???? I have .055 now. I don't think that's enough...
Easy 904 question
Posted By: WheelsUp73
Re: Easy 904 question - 11/12/11 01:01 AM
It should be set up from .060 to .070
Posted By: DemonDust
Re: Easy 904 question - 11/12/11 01:21 AM
Quote:
It should be set up from .060 to .070
I'm using my thinnest ring. So is .055 to tight? Will it cause problems?
Posted By: dusturbd340W5
Re: Easy 904 question - 11/12/11 01:28 AM
I don't think you will see a problem with .055
Posted By: WheelsUp73
Re: Easy 904 question - 11/12/11 01:38 AM
Quote:
I don't think you will see a problem with .055
I don't either. I would run it if it were mine.
Posted By: turbocolt2.4L
Re: Easy 904 question - 11/12/11 10:34 PM
it'll be fine run it
Posted By: DemonDust
Re: Easy 904 question - 11/13/11 12:20 AM
Thanks guys! I took it apart one last time and cleaned everything real good with brake cleaner got all the packaging grease off of the steels and pressed down on the discs. I got .057 I feel pretty comfortable with my results...
Now I just need some new snap rings for my governor.. I seem to have misplaced one
Now I just need some new snap rings for my governor.. I seem to have misplaced one
Posted By: John_Kunkel
Re: Easy 904 question - 11/13/11 09:40 PM
An easy way to pick up a little clearance is to thin the pressure plate in a lathe.
Posted By: 70AARcuda
Re: Easy 904 question - 11/13/11 10:24 PM
Quote:
An easy way to pick up a little clearance is to thin the plessure plate in a lathe.
I have thinned the pressure plate on 4 904s went going from 4 disc to 5 disc. I measure the clearance, the take pressure plate to machine shop who surfaces it with grind stones.
I usually get about .055 plus or minus and open the clearance to .070..plus i get a nice clean flat surface on the pressure plate.
Posted By: dOrk !
Re: Easy 904 question - 11/13/11 10:28 PM
Quote:
An easy way to pick up a little clearance is to thin the plessure plate in a lathe.
Is that a PLEASURE plate ?.... I wood like to have one of those ...
Posted By: Guitar Jones
Re: Easy 904 question - 11/13/11 11:54 PM
Quote:Quote:
An easy way to pick up a little clearance is to thin the plessure plate in a lathe.
Is that a PLEASURE plate ?.... I wood like to have one of those ...
I've heard you already have one.
Posted By: dOrk !
Re: Easy 904 question - 11/14/11 12:12 AM
Quote:
I've heard you already have one.
You heard wrongO ... how is yours wurking ? ... even-though it is an IMport !
Posted By: John_Kunkel
Re: Easy 904 question - 11/14/11 08:16 PM
Quote:
Is that a PLEASURE plate ?.... I wood like to have one of those ...
50 mph fingers and 20 mph brain. I corrected the typo.
Posted By: Guitar Jones
Re: Easy 904 question - 11/14/11 08:47 PM
Quote:Quote:
I've heard you already have one.
You heard wrongO ... how is yours wurking ? ... even-though it is an IMport !
Got a whammy bar too.