Moparts

Finally got on the dyno

Posted By: hemi-itis

Finally got on the dyno - 09/27/11 01:44 AM

It was a long time coming after a few postponments got on the dyno last week with my hemi that was just freshened by Alan from Advanced Race cars{ARC here on the board} out of Patterson.Took me a few days to absorb what happened in the 2 afternoons on the dyno.After mounting the engine and all hoses & wires filled the SV1 carbs with pump gas and a feww squirts and it fired at the hit of the starter.Great start,went to start some pulls and there was an issue with the dyno throttle and my carbs.The 11 inches of vacume under the carbs was too much for the dyno to open.I was noy happy To my surprise,There was this guy loitering at the shop that just happened to have a real nice pair of PRO SYSYTEMS Dominators he would allow me to use He was alreadt kind enough to ley me use his "A" body headers so that the o/2 sensors had a good location.So I must give Steve Gill {steve gillman} here on the bord a HUGE thank you for being in the right place at the right time .I don't usaually have that luck.Bill & Frank are awsome guys from Bill Cerralli Racing and help make my visit very comfortable and enjoying.Frank ran the dyno and made me very happy!!

Check out the Vid>>>> http://www.youtube.com/watch?v=YpXgN2Ul2...&playnext=4

Attached picture 6843889-DYNODAY9.19012.JPG
Posted By: CUUDAK

Re: Finally got on the dyno - 09/27/11 02:48 AM

Numbers??
Posted By: Clanton

Re: Finally got on the dyno - 09/27/11 03:08 AM

i bet it felt good to make some noise!
Posted By: hemi-itis

Re: Finally got on the dyno - 09/27/11 04:16 AM

Waited a long time to cross that hurdle.Made some very conservitive pulls starting at 26* timing and pump gas at 4 lbs of boost made 700ish. 28* race gas @8 lbs about 800 HP and 10 lbs made 900.I ran out of pullies for more boost. The word at PRO TORQUE,Joe said 3 weeks to get a converter right now.So hurry up and wait.

Attached picture 6844274-DYNODAY9.19011.JPG
Posted By: Dap

Re: Finally got on the dyno - 09/28/11 02:18 AM

Great going Al. I am glad to see you got it done. Runs better without the 750's you had on there
so how much boost is that thing capable of putting out? Breaking the 1,000 mark should be a no brainer.
Posted By: hemi-itis

Re: Finally got on the dyno - 09/28/11 04:15 AM

1000+ is just a pulley change away.I'll wait 'till after the data logger is installed before going more than 10 lbs It's still a streeter
Posted By: 68KillerBee

Re: Finally got on the dyno - 09/28/11 11:21 PM

Looks killer, what car is it going into?
Posted By: hemi-itis

Re: Finally got on the dyno - 09/29/11 12:08 PM

Right back where it came from

Attached picture 6847476-113-1328_IMG.JPG2R2.jpg
Posted By: fishy340

Re: Finally got on the dyno - 09/29/11 10:44 PM

hey AL best of luck,how many lbs if need be,can that blower push w ur engine? and on a side note ur boys belly! looks like he's hideing a helmet under his shirt...lol j/k
Posted By: BlownHemiCharger

Re: Finally got on the dyno - 09/29/11 11:00 PM

Quote:

Waited a long time to cross that hurdle.Made some very conservitive pulls starting at 26* timing and pump gas at 4 lbs of boost made 700ish. 28* race gas @8 lbs about 800 HP and 10 lbs made 900.I ran out of pullies for more boost. The word at PRO TORQUE,Joe said 3 weeks to get a converter right now.So hurry up and wait.



What is the cubic inches? And whos heads did you go with. I am building a 540 blown hemi and was just curious, looking to get around the same numbers!
Posted By: hemi-itis

Re: Finally got on the dyno - 09/30/11 12:50 AM

Quote:

hey AL best of luck,how many lbs if need be,can that blower push w ur engine? and on a side note ur boys belly! looks like he's hideing a helmet under his shirt...lol j/k

U r a fny guy JK

Andy,that blower can make over 20 lbs,,,I guess I would LOVE to feel 15 lbs Hope to drive it before the 1st SNOW
Posted By: hemi-itis

Re: Finally got on the dyno - 09/30/11 12:56 AM

Quote:

Quote:

Waited a long time to cross that hurdle.Made some very conservitive pulls starting at 26* timing and pump gas at 4 lbs of boost made 700ish. 28* race gas @8 lbs about 800 HP and 10 lbs made 900.I ran out of pullies for more boost. The word at PRO TORQUE,Joe said 3 weeks to get a converter right now.So hurry up and wait.



What is the cubic inches? And whos heads did you go with. I am building a 540 blown hemi and was just curious, looking to get around the same numbers!



545 inch with stockish iron heads

Attached picture 6848385-005.JPG
Posted By: BlownHemiCharger

Re: Finally got on the dyno - 10/01/11 08:13 PM

Whats the Static Compression, only 4 Lbs on pump gas!!!
Posted By: hemi-itis

Re: Finally got on the dyno - 10/01/11 09:32 PM

Static is 8:1.With iron heads I didn't want to go more than 10:1 on pump gas.The timing was very conservitive @28*

http://www.blowerdriveservice.com/techcharts.php
Posted By: hemi-itis

Re: Finally got on the dyno - 10/01/11 09:44 PM

2nd pull was 25* of timing with HP of 721@6100
3rd pull was 28* with 739@ 6500 and 646 ft lbs.There is plenty left,just wanted some baseline info.

Attached picture 6851360-2011-09-21_00013.JPG
Posted By: BlownHemiCharger

Re: Finally got on the dyno - 10/01/11 10:04 PM

Quote:

2nd pull was 25* of timing with HP of [Email]721@6100[/Email]
3rd pull was 28* with 739@ 6500 and 646 ft lbs.There is plenty left,just wanted some baseline info.




Ok, I forgot you said Iron heads. I was starting to panic. But I am running fully ported stage V heads. So I will be able to get more boost out of it then 4 LBS.
Posted By: 383man

Re: Finally got on the dyno - 11/02/11 06:46 AM

All I can say is.........WOW ! And cool ! Ron
Posted By: HemiDave

Re: Finally got on the dyno - 11/08/11 12:15 AM

Cool numbers, Al! Always best to keep some in reserve...

Dave
Posted By: mopar_mark

Re: Finally got on the dyno - 11/08/11 01:08 AM

Congrats, nothing more pleasing than hearing your own Hemi sing on the dyno

Going to be a fun ride on the street thats for sure

All the best,
Mark . . .
Posted By: hemi-itis

Re: Finally got on the dyno - 11/08/11 02:58 PM

Thanks Mark,will you still be driving yours in the streets of our motherland??
Posted By: mopar_mark

Re: Finally got on the dyno - 11/08/11 07:02 PM

Quote:

Thanks Mark,will you still be driving yours in the streets of our motherland??


Oh yes Sir, got to be able to have fun on the streets

If I can get the money together & cars running good, I want to bring the Cuda to your homeland in 2013
Posted By: hemi-itis

Re: Finally got on the dyno - 11/10/11 06:25 AM

Quote:

Quote:

Thanks Mark,will you still be driving yours in the streets of our motherland??


Oh yes Sir, got to be able to have fun on the streets

If I can get the money together & cars running good, I want to bring the Cuda to your homeland in 2013



That would be very cool.which event??Shakedown?YB nats?
Posted By: mopar_mark

Re: Finally got on the dyno - 11/10/11 10:43 AM

Quote:

Quote:

Quote:

Thanks Mark,will you still be driving yours in the streets of our motherland??


Oh yes Sir, got to be able to have fun on the streets

If I can get the money together & cars running good, I want to bring the Cuda to your homeland in 2013



That would be very cool.which event??Shakedown?YB nats?



Early days yet, a couple of us have discussed bringing our cars over, in conjunction with a couple of other guys.

Drag was mentioned, although a bit 'Pie in the Sky' talk at the moment. At the end of the day it will come down to money, work comittments & approval from my wife

Anyway, thats enough about me, this is your thread, we need more progress & testing details
Posted By: hemi-itis

Re: Finally got on the dyno - 11/12/11 02:28 PM

I spoke with Joe at PRO Torque.He;s so busy there it unbelievable,you break a few records in turbo and the phone EXPLODES with new orders.He opologized gave me a great price and I'll wait let the real racers get thier stuff 1st.I'll be ready for spring

Attached picture 6915468-2011-09-21_00009.JPG
Posted By: Clanton

Re: Finally got on the dyno - 11/12/11 03:12 PM

good to hear you will be ready in the spring!
© 2024 Moparts Forums