Posted By: arc
hemi 99 dyno numbers - 08/18/11 01:15 AM
This is some numbers from my motor there is been alot of talk about big 99 motors and how much power they make. This motor has gone 6.99 in my 2300 pound car.
hemi 99 dyno numbers
Posted By: arc
Re: hemi 99 dyno numbers - 08/18/11 01:17 AM
Dyno sheet
Posted By: Eric
Re: hemi 99 dyno numbers - 08/18/11 01:23 AM
Very impressive... 
Posted By: B1Fish540
Re: hemi 99 dyno numbers - 08/18/11 01:33 AM
Thats alot of horsepower at only 7600 RPM! Sounds like it would be a very reliable combo. Curious, what are your CR and lift? Congrats, excellent build! 
Posted By: Bigcube
Re: hemi 99 dyno numbers - 08/18/11 01:39 AM
I too old to lean my head like that so I fixed it for you 
Very nice!
Very nice!
Posted By: arc
Re: hemi 99 dyno numbers - 08/18/11 02:29 AM
Quote:cr is 14.48 and the lift is 1.010 after lash
Thats alot of horsepower at only 7600 RPM! Sounds like it would be a very reliable combo. Curious, what are your CR and lift? Congrats, excellent build!
Posted By: arc
Re: hemi 99 dyno numbers - 08/18/11 02:32 AM
1
Posted By: Dragula
Re: hemi 99 dyno numbers - 08/18/11 02:55 AM
I knew you were making a lot of hp, very impressive. If I remember, you had a billet block and 650 cubes correct? Is it also a water block? Please post a pic or two if you could.
Posted By: hemi-itis
Re: hemi 99 dyno numbers - 08/18/11 03:43 AM
Linky no worky fo me 
Posted By: arc
Re: hemi 99 dyno numbers - 08/18/11 03:51 AM
Posted By: hemi-itis
Re: hemi 99 dyno numbers - 08/18/11 04:24 AM
SWEEEEEEEET!!!
Posted By: Al_Alguire
Re: hemi 99 dyno numbers - 08/18/11 05:18 AM
Very nice. Was it back on the dyno because oif an issue or just looking for more. How has the valvetrain been since you went with this combo?
Posted By: fishy340
Re: hemi 99 dyno numbers - 08/18/11 02:02 PM
Quote:is that the motor in 10.5 drews bu? j/k love that car of urs.
Dyno sheet
Posted By: arc
Re: hemi 99 dyno numbers - 08/18/11 02:27 PM
Quote:we had a lifter brake on us and had a lot of pushrod tip burn on us but I think we got it
Very nice. Was it back on the dyno because oif an issue or just looking for more. How has the valvetrain been since you went with this combo?
fixed.
Posted By: arc
Re: hemi 99 dyno numbers - 08/18/11 02:31 PM
Quote:thanks I'm not that good with the phone
I too old to lean my head like that so I fixed it for you
Very nice!
Posted By: arc
Re: hemi 99 dyno numbers - 08/18/11 02:34 PM
Quote:I think Ray stiped no hemi lolQuote:is that the motor in 10.5 drews bu? j/k love that car of urs.
Dyno sheet
Posted By: Diablo
Re: hemi 99 dyno numbers - 08/18/11 03:10 PM
Quote:Quote:we had a lifter brake on us and had a lot of pushrod tip burn on us but I think we got it
Very nice. Was it back on the dyno because oif an issue or just looking for more. How has the valvetrain been since you went with this combo?
fixed.
What did you feel fixed your problem with the burning tips? We had that problem with our TS engine and the fix was going a bigger size with Mantons tool steel tips. Not a problem since that change.
Posted By: arc
Re: hemi 99 dyno numbers - 08/18/11 03:36 PM
I put mantons in it with the bronze cups
Posted By: B1CUDA
Re: hemi 99 dyno numbers - 08/18/11 04:38 PM
Quote:
I put mantons in it with the bronze cups
Good move. I did the same thing with my Hemi. I wasn't burning tips, but, I decided to go to the bronze cups, as the previous engine builder used an enormous rocker adjuster, that made no sense to me, or Terry Manton.
I only have a wimpy, little 500" motor....
Posted By: CompWedgeEngines
Re: hemi 99 dyno numbers - 08/18/11 05:13 PM
Interesting.
Posted By: camastomcat
Re: hemi 99 dyno numbers - 08/19/11 03:30 AM
Arc,
Does your car weigh 2400#'s with the driver and full of fuel? That's some motor. Also, what block? 5 cam bearing or 9? Size CI would be good to know and if it's a water block or not. Thanks and nice build with killer numbers.
Does your car weigh 2400#'s with the driver and full of fuel? That's some motor. Also, what block? 5 cam bearing or 9? Size CI would be good to know and if it's a water block or not. Thanks and nice build with killer numbers.
Posted By: arc
Re: hemi 99 dyno numbers - 08/19/11 03:41 AM
Quote:2300 after a pass with driver.I have a cn billet block with a 60 mm 9 cam bearings it is a water block.the dyno is the same one your motor was on last week.
Arc,
Does your car weigh 2400#'s with the driver and full of fuel? That's some motor. Also, what block? 5 cam bearing or 9? Size CI would be good to know and if it's a water block or not. Thanks and nice build with killer numbers.
Posted By: hemi-itis
Re: hemi 99 dyno numbers - 08/19/11 04:02 AM
You 2 guys will be a hard act to follow 
Hope I can get on there next week 
Hope I can get on there next week
Posted By: Al_Alguire
Re: hemi 99 dyno numbers - 08/19/11 06:08 AM
Very nice. Thanks for sharing the dyno info as the pushrod issue. Seems to be an issue with them for sure. Stout ppiece and nice car.
Posted By: DusterDj
Re: hemi 99 dyno numbers - 08/19/11 02:18 PM
Nice...
Posted By: Adrielp
Re: hemi 99 dyno numbers - 08/19/11 03:54 PM
Quote:
Nice...
Arc, which bore spacing hemi is this? the 5.0 or the 4.9. Also, what is the bore, stroke?(if you don't mind divulging that info.
Posted By: arc
Re: hemi 99 dyno numbers - 08/19/11 04:35 PM
Quote:4.90 bore spacing 4.672 bore 4.75 stroke10.800 deckQuote:
Nice...
Arc, which bore spacing hemi is this? the 5.0 or the 4.9. Also, what is the bore, stroke?(if you don't mind divulging that info.
Posted By: camastomcat
Re: hemi 99 dyno numbers - 08/20/11 02:59 AM
2300 after a pass with driver.I have a cn billet block with a 60 mm 9 cam bearings it is a water block.the dyno is the same one your motor was on last week.
Wow, that is gonna fly. 1360HP is huge in a Mopar especially at that RPM. So that's the 650CI we saw earlier? How did they make a billet block with water? Or do the heads just cool the motor? Anyway, you east coast Jersey guys make some power.
Posted By: 7sec.cuda
Re: hemi 99 dyno numbers - 08/20/11 04:58 PM
congrats good for u
Posted By: RT540
Re: hemi 99 dyno numbers - 08/20/11 05:22 PM
Awesome engine 