Is anyone using Stahl SB A-Body headers?

Is anyone using Stahl SB A-Body headers? - 12/10/10 10:12 PM

If so how well do they fit? Also do you have any Pics of them in the car and how close do they come to the oil pan?
Thinking about a set for my Street car with W2 heads.

Posted By: cgall

Re: Is anyone using Stahl SB A-Body headers? - 12/11/10 04:50 AM

I had an old pair of big block 2" fenderwells and the fit and quality were good, but when it was time to replace them, the cost was 2X Hookers or Proparts. I got the Proparts and there was no difference in performance.

Posted By: Max Weg

Re: Is anyone using Stahl SB A-Body headers? - 12/11/10 05:07 AM

Quote:

If so how well do they fit? Also do you have any Pics of them in the car and how close do they come to the oil pan?
Thinking about a set for my Street car with W2 heads.

I have a set on my Stock Eliminator each side has one tube that exits through the fenderwell and wraps around the frame. The fit fairly well and are not to close to the oil pan. I will check photos and see if I have one with the oil pan in view.

Max Weg

Posted By: topside

Re: Is anyone using Stahl SB A-Body headers? - 12/11/10 05:08 AM

Been a set on my '70 Duster since it was new; it's always been a drag car. Slip-fit primaries, one on each side goes through the apron, collectors bolt on using tabs. Clears a huge oil pan & the trans, tight at idler arm. Tight at brake lines. Requires adapters at the cylinder head if your heads have the OEM bolt pattern. Flanges are real tight if you use 13/16" spark plugs, but 5/8" are a breeze. No interference with my 7.10x15 Moroso ft tires. No ground clearance issues unless your trailer lacks a beaver-tail.
Here's a left-side photo, with Batten W2 heads. Being an old SS/IA car, the engine location's been juggled a bit.

Attached picture 6350338-im000155.jpg

Posted By: S/ST 3040

Re: Is anyone using Stahl SB A-Body headers? - 12/11/10 12:00 PM

Does anybody have a set of $tahl 1 3/4" x 3" for A-body/SB? (stock heads)

I have a set of Hooker 5303 (1 7/8") and think 1 3/4" might be a little
quicker for my 340.

Attached picture 6350679-DSCN1745.JPG

Posted By: Darryls-Demon

Re: Is anyone using Stahl SB A-Body headers? - 12/11/10 03:56 PM

I think The $tahl 1 3/4 x 3 would be the best size for my mild 408, seems to me the 1 5/8 TTi step headers would be to small and the 1 7/8 too big.
Any one have a nice set they want to sell?

Posted By: mr. 63plymouth

Re: Is anyone using Stahl SB A-Body headers? - 12/11/10 07:13 PM

Here are the only pic I have, in a 68 barracuda! With these headers the car went 9.52@ 143! In street clothes!! Love them. And they might be for sale!! ! 1/3/4" x 3"

Attached picture 6351199-HPIM35122.jpg

Posted By: Darryls-Demon

Re: Is anyone using Stahl SB A-Body headers? - 12/13/10 05:50 PM

Any one else using these headers?

Posted By: S/ST 3040

Re: Is anyone using Stahl SB A-Body headers? - 02/26/11 08:13 PM

Quote:

And they might be for sale!! ! 1/3/4" x 3"

Do you still have the Stahl 1 3/4" x 3" headers?