Posted By: The Cuda Guy
MW Stealth Heads - 11/10/10 03:19 PM
Guys can the Stealths be brought out to MW? I used the search button... and no real answer other than some guy on bbdart.com did it. Anyone got any feedback?
Don
Don
MW Stealth Heads
Posted By: Stanton
Re: MW Stealth Heads - 11/10/10 04:08 PM
That's what you get when you buy the CNC'd version.
Posted By: The Cuda Guy
Re: MW Stealth Heads - 11/10/10 04:45 PM
Are you sure? I dont see it mentioned anywhere that they are MW ports? I have the CNC version. Thanks.
PS. I stole that pic from this forum. Not my heads.
Don
PS. I stole that pic from this forum. Not my heads.
Don
Posted By: TonyS451
Re: MW Stealth Heads - 11/10/10 04:51 PM
I have the CNC stealths and they are not max wedge sized ports. However, I spoke with Jeff at Modern Cyl head (does the cnc work for 440source) and he said they can be opened up to MW if need be. No big flow advantages though, other than being able to run some arguably better intake manifolds.
Posted By: The Cuda Guy
Re: MW Stealth Heads - 11/10/10 05:14 PM
Quote:
I have the CNC stealths and they are not max wedge sized ports. However, I spoke with Jeff at Modern Cyl head (does the cnc work for 440source) and he said they can be opened up to MW if need be. No big flow advantages though, other than being able to run some arguably better intake manifolds.
Thanks man, this was the feedback I was looking for.
Don
Posted By: moparniac
Re: MW Stealth Heads - 11/10/10 05:34 PM
Quote:
I have the CNC stealths and they are not max wedge sized ports. However, I spoke with Jeff at Modern Cyl head (does the cnc work for 440source) and he said they can be opened up to MW if need be. No big flow advantages though, other than being able to run some arguably better intake manifolds.
X2 ! Now don if you do that you should prolly run the 2d cause the bigger intakes won't fit under your dual snorkel hood ! Remember I have some engine lower kit to drop ya 1/2" if need be!
Posted By: moparniac
Re: MW Stealth Heads - 11/10/10 05:38 PM
Don! Buy my converter! a9sec70cuda will attest to the quality ! 
Posted By: maximum entropy
Re: MW Stealth Heads - 11/10/10 06:13 PM
x3. the cnc stealths are not mw, and i wouldn't recommend going any bigger than the cnc port job. personally, i won't use the stealths again. i tried them once and they cracked badly within a few runs. shattered, actually. to their credit, they promptly replaced them with a new set, which have been working fine since then, and they make good power, but i am gunshy.
Posted By: mopardamo
Re: MW Stealth Heads - 11/11/10 02:20 AM
Hello,
Jeff has 2 versions of his cnc program. They flow very close to the same numbers. The near MW version is purely to provide additional volume for the larger ci motors. It helps fill the cylinders better. Id use the near MW version for anything 500ci or larger.
Damon
Jeff has 2 versions of his cnc program. They flow very close to the same numbers. The near MW version is purely to provide additional volume for the larger ci motors. It helps fill the cylinders better. Id use the near MW version for anything 500ci or larger.
Damon
Posted By: sixpackgut
Re: MW Stealth Heads - 11/11/10 03:00 AM
just to avoid the bathtub intake for the rest of your life would be worth it to go MW size with the 337 intake and use regular MW gaskets 