Posted By: VernMotor
Getting closer ! - 06/26/21 02:32 AM
Started this in Feb. 5 months ago. Never dream it be this hard to get parts. hope the last one comes tomorrow ( oil pump) Never did get a new oil pan.
Getting closer !
Posted By: tex013
Re: Getting closer ! - 06/26/21 11:50 AM
Looks great .
Tex
Tex
Posted By: MR_P_BODY
Re: Getting closer ! - 06/26/21 01:10 PM
Lookin good Vern.. just about done 
Posted By: mopar dave
Re: Getting closer ! - 06/26/21 01:40 PM
Looks good. I haven't been following, what cubic inch, compression and cam did you go with?
Posted By: VernMotor
Re: Getting closer ! - 06/26/21 03:26 PM
Originally Posted by mopar dave
Looks good. I haven't been following, what cubic inch, compression and cam did you go with?
499 13.4-1 Bullet cam 649/620 lift 1.6 rockers
Posted By: gregsdart
Re: Getting closer ! - 06/26/21 03:31 PM
Looks great! What kind of power do you think it will make?
Posted By: mopar dave
Re: Getting closer ! - 06/26/21 03:37 PM
Nice. I'm guessing a 270ish at 50? That should make some steam (700hp+).
Posted By: VernMotor
Re: Getting closer ! - 06/26/21 05:11 PM
Originally Posted by mopar dave
Nice. I'm guessing a 270ish at 50? That should make some steam (700hp+).
Trick flow 270 heads.. Indy intake . I don't know I was thinking 650 maybe.
Posted By: tex013
Re: Getting closer ! - 06/27/21 09:36 PM
Originally Posted by VernMotor
Originally Posted by mopar dave
Nice. I'm guessing a 270ish at 50? That should make some steam (700hp+).
Trick flow 270 heads.. Indy intake . I don't know I was thinking 650 maybe.
Wallace estimates mine @ 650/670ish . With your bigger comp, race gas ? , you should be a bit more .
Stock block ?
Tex
Posted By: VernMotor
Re: Getting closer ! - 06/28/21 12:59 AM
Originally Posted by tex013
Originally Posted by VernMotor
Originally Posted by mopar dave
Nice. I'm guessing a 270ish at 50? That should make some steam (700hp+).
Trick flow 270 heads.. Indy intake . I don't know I was thinking 650 maybe.
Wallace estimates mine @ 650/670ish . With your bigger comp, race gas ? , you should be a bit more .
Stock block ?
Tex
Stock block billet main caps - E-85
Posted By: tex013
Re: Getting closer ! - 06/28/21 07:26 AM
Getting close to limit .
Good luck
Tex
Good luck
Tex
Posted By: JERICOGTX
Re: Getting closer ! - 06/28/21 12:11 PM
Is that a Moroso pressure relief valve?
Looks good.
Looks good.
Posted By: VernMotor
Re: Getting closer ! - 06/28/21 03:24 PM
Originally Posted by JERICOGTX
Is that a Moroso pressure relief valve?
Looks good.
Looks good.
I bought that indy valley plate used and them fittings was in it.
Posted By: VernMotor
Re: Getting closer ! - 06/28/21 03:25 PM
Got a little more done.
Posted By: tboomer
Re: Getting closer ! - 06/28/21 05:31 PM
Looking good!
Posted By: HardcoreB
Re: Getting closer ! - 06/28/21 06:14 PM
Nice!
Posted By: birdtracker
Re: Getting closer ! - 06/28/21 08:57 PM
I got mine back together and actually drove it down the road yesterday. Mine is 41 more cubic inches, but only 12.5-1 compression and a Bullet .685/ .685 cam. What fuel are you running ? And did the valley tray fit right in or did you have to have it machined? Birdtracker
Posted By: VernMotor
Re: Getting closer ! - 06/28/21 10:15 PM
Originally Posted by birdtracker
I got mine back together and actually drove it down the road yesterday. Mine is 41 more cubic inches, but only 12.5-1 compression and a Bullet .685/ .685 cam. What fuel are you running ? And did the valley tray fit right in or did you have to have it machined? Birdtracker
I run e-85 . I did't do anything to the plate fit good.
Posted By: VernMotor
Re: Getting closer ! - 06/29/21 02:25 AM
Oil pump and seat belts came today !! two parts in day ! that a record ....
Posted By: metallicareload
Re: Getting closer ! - 06/29/21 04:07 AM
Originally Posted by VernMotor
Got a little more done.
Looking good, what valve covers are those?!
Posted By: Clanton
Re: Getting closer ! - 06/29/21 03:09 PM
Sounds like a great engine and a good job naturally putting it together.Did all of your rockers clear the covers on the p/r side?
Posted By: VernMotor
Re: Getting closer ! - 06/30/21 12:48 AM
Originally Posted by metallicareload
Originally Posted by VernMotor
Got a little more done.
Looking good, what valve covers are those?!
I got them from summit not sure on the brand,, they say SPC I think on the inside.
Posted By: VernMotor
Re: Getting closer ! - 06/30/21 12:49 AM
Originally Posted by Clanton
Sounds like a great engine and a good job naturally putting it together.Did all of your rockers clear the covers on the p/r side?
Yes they do
Posted By: VernMotor
Re: Getting closer ! - 06/30/21 01:56 AM
I got it down in it's hole today.. light a fire in it tomorrow
Posted By: tex013
Re: Getting closer ! - 06/30/21 04:28 AM
thats great
Tex
Tex
Posted By: tboomer
Re: Getting closer ! - 06/30/21 10:29 AM
Looks great just sitting there! Does your daughter still drive?
Posted By: 69dart
Re: Getting closer ! - 06/30/21 04:57 PM
Looking good!!!