Posted By: RAY1969CARS
Which automatic shifter are you using !!?? - 03/11/15 02:14 AM
And why do you like it
Quote:
B&M Pro Ratchet.... why... because it has NEVER missed
a shift
Quote:
B&M Pro Ratchet.... why... because it has NEVER missed
a shift
Quote:
Im a Street / Strip guy.... using a B&M Quicksilver. Bought it because I liked the look. Found that I love the way it works.
Quote:. I agree same reason why I use one
B&M Pro Ratchet.... why... because it has NEVER missed
a shift
Quote:
Hurst 1/4 stick...b/c I hate ratchet shifters.
Quote:Quote:
Hurst 1/4 stick...b/c I hate ratchet shifters.
That's what I would use if I ever parted ways with my cheetah, I feel the same about ratchet shifters.
Quote:
ANY Mopar benefits from a rear exit shifter cable IMO.
Clearing the starter, header and torsion bar can be a real challenge with the front exit cables!
Quote:Quote:
ANY Mopar benefits from a rear exit shifter cable IMO.
Clearing the starter, header and torsion bar can be a real challenge with the front exit cables!
... I have to rap the shifter cable with high
temp covering just to make sure it doesnt burn.. no
big deal.. but if I could get a rear exit on the
pro ratchet that would be the ultimate ... JMO
Quote:
Hurst Promatic 2.........stupid simple.
Quote:
PPP 3 speed in the Challenger and Stealth black Pro Bandit 2 speed in the Scamp. Both great shifters. Both also air shifted
Quote:
better sit down son.....
Quote:
better sit down son.....
Quote:Quote:
PPP 3 speed in the Challenger and Stealth black Pro Bandit 2 speed in the Scamp. Both great shifters. Both also air shifted
What doz one of those bad boys go for ??? 400.00
Quote:
Well I was going to put a B&M Pro Ratchet in my GTX build but now I am leaning towards the PPP. The rear exit is too good to pass up.
How do you even put a front exit cable with a CSR shield? I have a Cheetah in my race car with the rear entry and it is wonderful to have the rear entry, but the Cheetah is not a street shifter.
Quote:Quote:
Well I was going to put a B&M Pro Ratchet in my GTX build but now I am leaning towards the PPP. The rear exit is too good to pass up.
How do you even put a front exit cable with a CSR shield? I have a Cheetah in my race car with the rear entry and it is wonderful to have the rear entry, but the Cheetah is not a street shifter.
I burnt 1 shifter cable using the pro ratchet.. that
was the very first cable.. it was a bit short and I
didnt cover it.. I was being brave.. since then I
use a longer cable and I DONT use the heavy duty one..
they are a lot stiffer and harder to bend to clear
things... but I heat wrap it just to be sure... never
burnt up another... I'll wrap it just so I can use
the shifter I like... this cable has been in there
14 years now
Quote:Quote:Quote:
Well I was going to put a B&M Pro Ratchet in my GTX build but now I am leaning towards the PPP. The rear exit is too good to pass up.
How do you even put a front exit cable with a CSR shield? I have a Cheetah in my race car with the rear entry and it is wonderful to have the rear entry, but the Cheetah is not a street shifter.
I burnt 1 shifter cable using the pro ratchet.. that
was the very first cable.. it was a bit short and I
didnt cover it.. I was being brave.. since then I
use a longer cable and I DONT use the heavy duty one..
they are a lot stiffer and harder to bend to clear
things... but I heat wrap it just to be sure... never
burnt up another... I'll wrap it just so I can use
the shifter I like... this cable has been in there
14 years now
Been there done that. But my question is with the CSR shield right up against the floor boards, isn't the location where the shifter cable goes through the floor be in the same spot as the CSR shield? Is it possible to use a front exit shifter with the CSR shield?
Quote:
I have a CSR shield and a front exit shifter. The hole in my floorboard is behind the rear of the shield...no problem there.
Quote:
Well I was going to put a B&M Pro Ratchet in my GTX build but now I am leaning towards the PPP. The rear exit is too good to pass up.
How do you even put a front exit cable with a CSR shield? I have a Cheetah in my race car with the rear entry and it is wonderful to have the rear entry, but the Cheetah is not a street shifter.
Quote:
I never cared for that PPP shifter... I could make
that in my shop...
Quote:Quote:
I never cared for that PPP shifter... I could make
that in my shop...
Talk is cheap.... Let's see you do it.
Maybe Ray can beta test it.