Moparts

Stroker Hemi combos, ET/power #s

Posted By: 408cuda

Stroker Hemi combos, ET/power #s - 12/29/13 07:49 AM

Cabin fever is here. Boxes of parts complied for my Hemi but no time for my own stuff and much more parts/$ needed anyhow. Was thinking you guys and gals could share some of your badass Hemi builds to hold me over? Size, basic combo, et/power #s etc. Street or strip, all good to me!
Posted By: Mulehead

Re: Stroker Hemi combos, ET/power #s - 12/29/13 03:26 PM

New Build 1

Attached picture 7975462-DSC06148.JPG
Posted By: Mulehead

Re: Stroker Hemi combos, ET/power #s - 12/29/13 03:26 PM

New Build 2

Attached picture 7975464-DSC06147.JPG
Posted By: DaveRS23

Re: Stroker Hemi combos, ET/power #s - 12/29/13 05:48 PM



505" al KB, 10.71 BDS, 246*/256* roller.

640+ RWHP on pump gas. 68 Dart street/strip car.
Posted By: Dragula

Re: Stroker Hemi combos, ET/power #s - 12/29/13 06:12 PM

Well...I detuned my Hemi for reliability and to be legal Nostalgia Mod Gas....Still 11.6:1 compression, still pump gas friendly, 484 cubes, good flowing heads but more room in them yet maybe 20cfm, good size valves, ported intake...It definitly liked the TR better, but I have an SV1 on the way that should wake it up...

Made +750hp Injected with a real cam....





Under carburated and with a very mild cam, and less valve spring pressure, its made 665hp so far with an ignition miss, and a crack in the intake...Had the intake welded up and I think I found the ignition miss...Still tuning it though.



Posted By: mickm

Re: Stroker Hemi combos, ET/power #s - 12/29/13 07:45 PM

not the best picture...
540 c.i. 10.3:1, 248/255 - .605/.588 cam, stage V heads and intake, 2 edelbrock 650's. did 712 at 6k, now using that to tear up the rear tires!

Attached picture 7975753-IMG_1721.jpg
Posted By: Hemi Allstate

Re: Stroker Hemi combos, ET/power #s - 12/29/13 11:32 PM

I haven't had this one on the dyno, and only a few times down the track. The entire car is a new build and not dialed in.
My Hemi is 572" alum. World block, CP 10.5 pistons, Stage V replacement heads CNC @ MCH. Comp solid roller from Dwayne Porter. The carb is a 4150 race Demon RS for now, and that is where I am looking to make changes. I have a 426- 3 and a Rat Roaster X ram to play with in the future.
Not pushing the car hard at all, short shifting about 6,000. Have three passes with best of 6.13 @ 113.3 mph.
Running pump gas.
Mark

Attached picture 7976044-!cid_00c501cd235f$07ed4d30$6FB1F383@MobileUnit1.jpg
Posted By: grncpe

Re: Stroker Hemi combos, ET/power #s - 12/30/13 01:20 AM

Mine is 588" 4.5 bore, 4.625 stroke. mopar ported heads, flow 415@800 lift. 760,740 284@.50 roller. 12to1 comp. potrted stage V intake, 2 800 cfm afb's Made 836hp @6700, 730tq @ 5300, My car is all steel,full interior on a 10" tire, & leafs. very nose heavy. so far 1.27 60' 9.53@ 142mph. still not a stellar run.

Posted By: 408cuda

Re: Stroker Hemi combos, ET/power #s - 12/30/13 08:12 AM

Awesome iron. Some quality hot rods for sure.

My build is much like Mickm, 520-540ish Stage V street/strip 4 speed.

Have you had yours to the strip at all Mick?

Thanks guys, keep em coming. Winter here is looong!
Posted By: quickd100

Re: Stroker Hemi combos, ET/power #s - 12/30/13 12:48 PM

605 Hemi, MP block, Indy rotating assembly kit, Indy 426SR heads, Bullet custom solid roller, .767/.676, 288/292, 113 centerline. Weiand tunnelram, 2 850 thermoquads, 12 quart pan,Milodon dual line system. 853hp@5800, 818ftlbs@4800. Performance?, best 60ft was a 1.45 spinning, haven't had a clean full 1/4 pass, last pass bent framerails on launch went into chassis shake and had to drop the throttle just past 1/8 mark, coasted through at 10.74@108. Dave
Posted By: 572charger

Re: Stroker Hemi combos, ET/power #s - 12/30/13 12:50 PM

606 cuin stage V big valve heads flow 450 at 28" 700 lift 720 lift roller 282 dur no2 cam 11.9 to 1 comp callies oliver diamond milodon gear drive ray barton oil pump charlies pan best run with single 1250 cfm dom and ray barton intake 9.60 at 141.79 on 93 octane pumpgas and 8.93 at 156 mph on a 200 hp tune , driven to the track and driven home 48 mile round trip , i weighs 3910 with me so u can do the HP math
Posted By: LAD 524

Re: Stroker Hemi combos, ET/power #s - 12/30/13 01:59 PM

Quote:

Mine is 588" 4.5 bore, 4.625 stroke. mopar ported heads, flow [Email]415@800[/Email] lift. 760,740 [Email]284@.50[/Email] roller. 12to1 comp. potrted stage V intake, 2 800 cfm afb's Made 836hp @6700, 730tq @ 5300, My car is all steel,full interior on a 10" tire, & leafs. very nose heavy. so far 1.27 60' 9.53@ 142mph. still not a stellar run.
[url=http://s823.photobucket.com/user/FabBakers/media/DSC01727_zps487fa57b.jpg.html]




Now thats tuff !

Here's mine - will be in at around 3500lbs. Made 845HP/770TQ, I hope I can go as fast as you have

Hemi mega block 4.5" bore - o-ringed
4.5" Bryant crank
Saenz 7.1" rods
11:1 Diamond pistons - coated tops/skirts
Sealed Power rings
ARP rod, crank, head studs, oil pan studs, flywheel bolts
Bullet roller 752/684" lift 270/280 @ .050" 112 & Isky Red Zone Xtreme EZ roller lifters
Indy Legend heads ported 420 cfm
Stage V rollers
MSD dist/box/crank trigger
Indy 426-4 4500 intake/have a 4500 Barton intake as well
Pro systems 1150
Electric water pump
Milodon ext dual line swinging pickup and pump
727 with all the good gear
Ultimate Convertor
9" 4.11s



Attached picture 7976661-IMG_0094copy.JPG
Posted By: mickm

Re: Stroker Hemi combos, ET/power #s - 12/30/13 09:27 PM

Quote:

Awesome iron. Some quality hot rods for sure.

My build is much like Mickm, 520-540ish Stage V street/strip 4 speed.

Have you had yours to the strip at all Mick?

Thanks guys, keep em coming. Winter here is looong!




no, haven't made it yet. dealing with a bunch of issues, most notably an ignition system that either misses badly near the rev limit, or has no rev limit.

hopefully this spring/summer.
Posted By: Thumperdart

Re: Stroker Hemi combos, ET/power #s - 12/30/13 09:35 PM

Quote:

605 Hemi, MP block, Indy rotating assembly kit, Indy 426SR heads, Bullet custom solid roller, .767/.676, 288/292, 113 centerline. Weiand tunnelram, 2 850 thermoquads, 12 quart pan,Milodon dual line system. [Email]853hp@5800[/Email], [Email]818ftlbs@4800.[/Email] Performance?, best 60ft was a 1.45 spinning, haven't had a clean full 1/4 pass, last pass bent framerails on launch went into chassis shake and had to drop the throttle just past 1/8 mark, coasted through at [Email]10.74@108.[/Email] Dave




This is too cool right there..............hopefully you can get the damage fixed and get some full passes............I see a feature show here w/the 405 boys.............You vs Farmtruck.........
Posted By: Sammy

Re: Stroker Hemi combos, ET/power #s - 12/30/13 09:50 PM

Quote:

Mine is 588" 4.5 bore, 4.625 stroke. mopar ported heads, flow [Email]415@800[/Email] lift. 760,740 [Email]284@.50[/Email] roller. 12to1 comp. potrted stage V intake, 2 800 cfm afb's Made 836hp @6700, 730tq @ 5300, My car is all steel,full interior on a 10" tire, & leafs. very nose heavy. so far 1.27 60' 9.53@ 142mph. still not a stellar run.

[url=http://s823.photobucket.com/user/FabBakers/media/airtime1_zps4c628866.jpg.html][image]http://i823.photobucket.com/albums/zz160/FabBakers/airtime1_zps4c628866.jp

g[/image][/url]





I'm demanding more pictures of this beautiful cuda
Posted By: dirty magnum

Re: Stroker Hemi combos, ET/power #s - 12/30/13 10:53 PM

Quote:

Quote:

Mine is 588" 4.5 bore, 4.625 stroke. mopar ported heads, flow [Email]415@800[/Email] lift. 760,740 [Email]284@.50[/Email] roller. 12to1 comp. potrted stage V intake, 2 800 cfm afb's Made 836hp @6700, 730tq @ 5300, My car is all steel,full interior on a 10" tire, & leafs. very nose heavy. so far 1.27 60' 9.53@ 142mph. still not a stellar run.

[url=http://s823.photobucket.com/user/FabBakers/media/airtime1_zps4c628866.jpg.html][image]http://i823.photobucket.com/albums/zz160/FabBakers/airtime1_zps4c628866.jp

g[/image][/url]





I'm demanding more pictures of this beautiful cuda


x2
Posted By: gregsrt

Re: Stroker Hemi combos, ET/power #s - 12/30/13 11:04 PM

Quote:

Quote:

Quote:

Mine is 588" 4.5 bore, 4.625 stroke. mopar ported heads, flow [Email]415@800[/Email] lift. 760,740 [Email]284@.50[/Email] roller. 12to1 comp. potrted stage V intake, 2 800 cfm afb's Made 836hp @6700, 730tq @ 5300, My car is all steel,full interior on a 10" tire, & leafs. very nose heavy. so far 1.27 60' 9.53@ 142mph. still not a stellar run.

[url=http://s823.photobucket.com/user/FabBakers/media/airtime1_zps4c628866.jpg.html][image]http://i823.photobucket.com/albums/zz160/FabBakers/airtime1_zps4c628866.jp

g[/image][/url]





I'm demanding more pictures of this beautiful cuda


x2




I had to right click/save when he posted pics of it a while ago. It is nice

Attached picture 7977128-DSC01690_zps0956ceac.jpg
Posted By: grncpe

Re: Stroker Hemi combos, ET/power #s - 12/30/13 11:23 PM

Sure!


I only have a few on photobucket... There was a thread on here while I was building it. I think it was SS/DA progress.... Thanks for asking
Posted By: Sammy

Re: Stroker Hemi combos, ET/power #s - 12/31/13 03:11 AM

Quote:

Sure!


I only have a few on photobucket... There was a thread on here while I was building it. I think it was SS/DA progress.... Thanks for asking





beautiful fish!
Come on an tease me some more. Awesome is an understatement.
Posted By: grncpe

Re: Stroker Hemi combos, ET/power #s - 12/31/13 04:01 AM

Dont want to mud up this guys thread with my stuff. Here is the link from when I was doing mine. I left out alot of the painting picks because I dont really like showing people how I do some things...just me. https://board.moparts.org/ubbthreads/show...part=1&vc=1
Posted By: an8sec70cuda

Re: Stroker Hemi combos, ET/power #s - 12/31/13 06:34 PM

572" hemi, KB block, MP heads CNC'd by MCH. 11:1 compression for pump gas.
Solid roller spec'd by Dwayne Porter...mild grind to be easy on parts.
Ray Barton single 4500 intake, 1200 pro systems dominator.
727, custom 5k stall, 4.10 gear, 295-65 drag radials. Cal-tracs rear suspension.
3800+ lb. '70 cuda, footbraked, full interior, street car.
9.54 at 140.4 mph, 1.320 sixty foot. All motor.

Attached picture 7978205-cudadriveway.JPG
Posted By: an8sec70cuda

Re: Stroker Hemi combos, ET/power #s - 12/31/13 06:37 PM

launch

Attached picture 7978214-cudalaunchattherock.JPG
Posted By: 67HEMI

Re: Stroker Hemi combos, ET/power #s - 12/31/13 07:45 PM

Mine is an all aluminum 496 Indy Maxx block.On the dyno it made 974 hp @ 6500 on 10 pounds of boost...got it home jetted it down 2 sizes and changed to 10 percent over and it made 14 pounds of boost so it should be around 1100 hp. 4.25 gun drilled callies xl crank.
Oliver rods
4.31 Ross Pistons/8.2 compression
Indy Legend-1 CNC heads
Dick Landy Rockers
Bullet/Morris roller cam Intake .707/272@.050 Ex .684/280@.050
Comp lifters
Smith Bros push rods
Charlies pan with swinging pickup
Milidon pump and single line cover
Supercharger USA Teflon stripped 10-71
2 Quick Fuel 1050 dominators
Mezeire high volume water pump
PTC Spragless convertor

Before install......


In the car.....

Posted By: Dragula

Re: Stroker Hemi combos, ET/power #s - 12/31/13 10:48 PM

Wow....I have the smallest Hemi on here...
Posted By: cudaman1969

Re: Stroker Hemi combos, ET/power #s - 12/31/13 11:41 PM

how about the small bore strokers 4.25-4.31x4.5, any comments
Posted By: sunroofgtx

Re: Stroker Hemi combos, ET/power #s - 01/07/14 01:23 AM

Guys, awesome combo's I've also noticed that 99% of you are running Firecore Wires. Thanks much. I finally get to see some of your combos. Below WAS mine. I am transplanting the Hemi into something a lot lighter. It was a 71 GTX. 4100 with me. 472, 10.75 to 1 re-worked crate. Indy rollers, 650 Cam Motion, Dominator, full 3" exhaust. Ran 5 10.81's @ all around 129 last time I ran it. Click below for a video at the YellowBullet Nats in Maryland.





Posted By: Dragula

Re: Stroker Hemi combos, ET/power #s - 01/07/14 02:28 AM

As soon as the weather allows...I will pull the intake and make the proper clearances to make this baby work...So making 660hp NA with an unsorted out 484 pump gas combo, going to make more very soon..

Posted By: 6PKRTSE

Re: Stroker Hemi combos, ET/power #s - 01/07/14 07:34 PM

Awesome thread. Who has the biggest cu in HEMI? Who's is making the most power? My KB HEMI is far from finished so i must live thru all of you for now.

Attached picture 7988833-100_1455[640x480].jpg
© 2024 Moparts Forums