Posted By: 72340dustermike
best intake for sbm with w-2 heads - 01/21/13 05:48 PM
im putting together a 0.40 over 340 with wisco 12/1 forged pistons
.590 lift cam roller rocker, roller lifters, oh ya stock stroke
i plan to lauch the car at 4200 shift at 7800
it is strictly a race motor in a 3200lb duster
would appreciate any help, looking for best flowing intake to
work with this combo as the heads have had work done to them also
thanks
Posted By: rt66jim
Re: best intake for sbm with w-2 heads - 01/21/13 07:48 PM
I run a Victor W2 but mine is a 416. I shift a 7000. I have run an Indy but the Victor was better by .03 and 3 mph.
Posted By: Brian Hafliger
Re: best intake for sbm with w-2 heads - 01/21/13 08:11 PM
The cheapest best intake is the Victor with a 1" open spacer.
The Indy with 1" cut off and a 1" tapered spacer will make more avg. power but at a premium cost compared to the victor. However, the Indy needs minor port work at the flange, so if you compare a full port on the Victor vs. Indy they might be close in price...only other factor would be carb height on Indy is fairly tall.
Brian
Posted By: MR_P_BODY
Re: best intake for sbm with w-2 heads - 01/21/13 08:26 PM
I like my Indy... I use the 1050 adapter to run
a 1050... runs great to 8200 on my 396ci... I used
it on my 340+ .030 and it pulled hard to 8000 but
that was about the limit on the cam
Posted By: 72demon416
Re: best intake for sbm with w-2 heads - 01/22/13 01:22 AM
As Brian said- the Victor is a good intake for a reasonable price- pretty hard to go wrong with. I ran one for a while and it was a good piece- I would buy it again if I went back to W2's.
Posted By: topside
Re: best intake for sbm with w-2 heads - 01/22/13 01:45 AM
I have a Holley Strip Dominator on mine (368") but I suppose a newer intake might make a bit more power.
Posted By: moparfan
Re: best intake for sbm with w-2 heads - 01/22/13 02:44 AM
How much better than the M-1 is the Victor?
Posted By: 72demon416
Re: best intake for sbm with w-2 heads - 01/22/13 04:30 AM
I had both on back to back and while I never got any numbers down with the M1 the victor pulled noticeably harder in the upper rpms.
Posted By: fed
Re: best intake for sbm with w-2 heads - 01/22/13 03:25 PM
How is the Holley Pro-dominator tunnelram?
Posted By: moparfan
Re: best intake for sbm with w-2 heads - 01/22/13 04:26 PM
Hi Brian, similar build to the orginal poster,11 to 1, hensley stage 2 ported w-2 econo long valve,72 cc open chamber head, the M-1 intake appears to be just gasket matched. the water port from the t-stat housing is blocked as well. 5500 8" converter 4:30 gear. The car has lazy 60' now (1.60 best)3250 lbs.
Mine is 40 over as well, 3.79 stroke. Crane .580" .600" lift, 268, 278 duration @ .050 crane flat tappet cam, Installed at card spec
Posted By: emarine01
Re: best intake for sbm with w-2 heads - 01/24/13 03:56 AM
Does anyone want to take a stab @ where the M1 falls as far as cid and rpm and explain the differences between the M1, victor and Indy and the best applications for each
Posted By: MR_P_BODY
Re: best intake for sbm with w-2 heads - 01/24/13 04:08 AM
I think Brian or someone with a dyno would be best
suited for that... it would eliminate some variables
Posted By: emarine01
Re: best intake for sbm with w-2 heads - 01/27/13 12:43 AM
Humm... No takers on this one,