Small block ?????

Posted By: 70dusterjohn

Small block ????? - 11/09/12 10:37 PM

DO you think that I could make an honest 750 to 850 hp with one ? Turbo of course. I have an 88mm and want to put it to use. I would like to run 8.80s and 5.60s in the 1/8. What would you build. I want to keep costs down so throw mw you ideas. What do you think 340 stroker, 318 stroker, ???? No 360s I dont have one.. And remember I'm a big block guy so act as though I'm stupid.. Cause, well I am..

Posted By: one bad fish

Re: Small block ????? - 11/09/12 11:00 PM

I don't see y not but u need a good block and some descent heads

Posted By: dogdays

Re: Small block ????? - 11/09/12 11:11 PM

You should be able to make an easy 2.5 hp/cubic inch with big heads and turbos.. You REALLY need an aftermarket block for this level of effort, though.

R.

Posted By: fasthawk6

Re: Small block ????? - 11/10/12 01:00 AM

You will be able to make that by mistake.A 88mm should be good for 1200hp.Get a good block 360-1 heads.

Posted By: 1967dartgt

Re: Small block ????? - 11/10/12 02:07 AM

If you are going to get a race block or ritter block, I would go 48* and run some w9s. With that set up you would have to try and keep the hp that low. LOL

Posted By: SpareParts

Re: Small block ????? - 11/10/12 02:50 AM

If it isn't going to be a street car you could try and fill the block. I think your goal is attainable but will definitely require a serious cylinder head and some thinking. A friend makes shy of 900 with a 4cyl DSM so why not with a SBM motor?

Posted By: jim sciortino

Re: Small block ????? - 11/10/12 04:18 AM

750 to 850 with a boosted SBM???

Without question.

It's a piece of cake N/A.

Posted By: Abodyjohn88

Re: Small block ????? - 11/10/12 05:19 AM

Give us some more info bout wat u want to do with the car..... Id say an r3 block and any w series head will do the job. Heck you could do it with w2s

Posted By: fishy340

Re: Small block ????? - 11/10/12 02:18 PM

I have a sb w a n2o cam in it that made 749hp w a big sv1 carb.I lost a few hp w my 4150.

Posted By: B1Johnny

Re: Small block ????? - 11/10/12 02:42 PM

my friend mike has a duster with b1ba heads stock block twin turbo made 1100 to the tire mild tune has been 8.20 at 3200 lbs.

Posted By: fishy340

Re: Small block ????? - 11/10/12 03:09 PM

Quote:

DO you think that I could make an honest 750 to 850 hp with one ? Turbo of course. I have an 88mm and want to put it to use. I would like to run 8.80s and 5.60s in the 1/8. What would you build. I want to keep costs down so throw mw you ideas. What do you think 340 stroker, 318 stroker, ???? No 360s I dont have one.. And remember I'm a big block guy so act as though I'm stupid.. Cause, well I am..

i have a complete shortblock sitting in a crate fresh that will take u there �2 w the right turbo.I mean headers and all.All u need is oil and fuel pump

Posted By: DakFink

Re: Small block ????? - 11/10/12 03:59 PM

Keeping cost down!

340 bore and stroked with a BPE stroke kit. (4.25" stroke) about $2350 or so

Dr Js Airwolf 220 Heads for about $2300
and a good LSM or Bullet cam.

The 88mm and a good Blow Through carb.

750-850 an easy walk in the park.

Posted By: Adobedude

Re: Small block ????? - 11/10/12 06:52 PM

Quote:

Keeping cost down!

340 bore and stroked with a BPE stroke kit. (4.25" stroke) about $2350 or so

Dr Js Airwolf 220 Heads for about $2300
and a good LSM or Bullet cam.

The 88mm and a good Blow Through carb.

750-850 an easy walk in the park.

What cam....

Posted By: mokid

Re: Small block ????? - 11/10/12 07:44 PM

I run a R3 W8 motor single carb makes 850 HP I'm currently having it re-built after breaking a rod cap, and my builder a chevy race engine builder is going to make a few changes like less dish in pistons maybe cam change but insist that we can get more HP out of this motor, I will update as build goes on. best time 9.03 149 mph.