Moparts

Stroker SB D-100 truck guys..what Header choices?

Posted By: Streetwize

Stroker SB D-100 truck guys..what Header choices? - 04/28/13 05:22 PM

I really wish someone like headman would make a 1 7/8" x 3 1/2" version of the 79030 or 79080 headers. I've even thought of buying a set just to use as a template to build a larger set.

What do you 400+ inch small block guys do? Does somebody make a big tube truck header I'm not aware of?
Posted By: dogdays

Re: Stroker SB D-100 truck guys..what Header choices? - 04/28/13 06:38 PM

I haven't seen one.
R.
Use them as the first step in a step header?
Posted By: Streetwize

Re: Stroker SB D-100 truck guys..what Header choices? - 04/28/13 07:11 PM

That's what I was thinking go from a 1 5/8 off the flange and step them up to 1 7/8 and then maybe run a flowmaster pulse-tech 4-2-1.

I may bite the bullet and buy a set of B body TTI's for my Rocky knowing I'm gonna have to cut and re-route a few tubes to fit the chassis. If my motor sat about 1" lower they would probably fit perfectly.

The Hedman 79030's would fit my chassis easily and have the flow advantage of a lot fewer bends than the A/B/E body headers I'm running now. I did weld a Schoenfeld 3 1/2" slip on collector on for now which I think is helping the top end.
Posted By: pinkduster

Re: Stroker SB D-100 truck guys..what Header choices? - 04/28/13 10:13 PM

My buddy and I were just talking about this today. He complained about the lack of big tube small block truck headers and wondered why he couldn't just use A-body big tube headers. Perhaps someone has been down this road before.
Posted By: hp340nos

Re: Stroker SB D-100 truck guys..what Header choices? - 04/28/13 10:35 PM

i built my own headers,they are tri-y stepped headers,1 3/4"
off the heads to 2",then 2, 2" into 3"collector,i bought the y collectors through stans headers.mine is a 340 stroker 418 in a 88 dakota. mike

Attached picture 7685779-077.JPG
Posted By: Streetwize

Re: Stroker SB D-100 truck guys..what Header choices? - 04/29/13 12:13 AM

Seriously, How hard could it be to take these from 1 5/8 x 3 to 1 7/8 x 3 1/2 and solve a LOT of issues for the truck market??

Attached picture 7685902-hed-79030_w.jpg
Posted By: BulletBob

Re: Stroker SB D-100 truck guys..what Header choices? - 04/29/13 02:24 AM

Hedman still makes a step header for the 72-93 trucks
Posted By: Jwilli500

Re: Stroker SB D-100 truck guys..what Header choices? - 04/29/13 04:23 AM

Wize,
If you find/figure out something please let us know!
Bob,
Any idea of a part # for those step headers?
Posted By: bigblock4x4

Re: Stroker SB D-100 truck guys..what Header choices? - 04/29/13 06:08 AM

look up maddog.com
Posted By: Streetwize

Re: Stroker SB D-100 truck guys..what Header choices? - 04/29/13 02:39 PM

maddog.com? No website

Maddogs.com = Resturaunt

I couldn't find any Hedman step headers for Dodges....lots of them for Chevies though.

I could almost section/shorten a set of Shoenfeld dirt track headers and make them work by whacking about 2 1/2" between the flanges and the first 90 degree turn
Posted By: bigblock4x4

Re: Stroker SB D-100 truck guys..what Header choices? - 04/29/13 03:08 PM

i went too maddog.net,i'm sorry,i just looked at them i didn't see any smallblock stuff,they got bigblock headers,they are nice and big up to 4"collector sizees and i think 2 1/4 inch primary tube sizes,they may build em though,maybe they have too be contacted,the bb mopar headers i think were 560 bucks!sorry for leading u in the wrong direction
© 2024 Moparts Forums