Previous Thread
Next Thread
Print Thread
best intake for sbm with w-2 heads #1373534
01/21/13 01:48 PM
01/21/13 01:48 PM
Joined: Dec 2012
Posts: 15
selah, washington
72340dustermike Offline OP
member
72340dustermike  Offline OP
member

Joined: Dec 2012
Posts: 15
selah, washington
im putting together a 0.40 over 340 with wisco 12/1 forged pistons
.590 lift cam roller rocker, roller lifters, oh ya stock stroke
i plan to lauch the car at 4200 shift at 7800
it is strictly a race motor in a 3200lb duster
would appreciate any help, looking for best flowing intake to
work with this combo as the heads have had work done to them also
thanks

Re: best intake for sbm with w-2 heads [Re: 72340dustermike] #1373535
01/21/13 03:48 PM
01/21/13 03:48 PM
Joined: Jan 2003
Posts: 4,002
Joplin, Mo
R
rt66jim Offline
master
rt66jim  Offline
master
R

Joined: Jan 2003
Posts: 4,002
Joplin, Mo
I run a Victor W2 but mine is a 416. I shift a 7000. I have run an Indy but the Victor was better by .03 and 3 mph.

Re: best intake for sbm with w-2 heads [Re: 72340dustermike] #1373536
01/21/13 04:11 PM
01/21/13 04:11 PM
Joined: Jan 2003
Posts: 5,484
SoCal
Brian Hafliger Offline
master
Brian Hafliger  Offline
master

Joined: Jan 2003
Posts: 5,484
SoCal
The cheapest best intake is the Victor with a 1" open spacer.
The Indy with 1" cut off and a 1" tapered spacer will make more avg. power but at a premium cost compared to the victor. However, the Indy needs minor port work at the flange, so if you compare a full port on the Victor vs. Indy they might be close in price...only other factor would be carb height on Indy is fairly tall.
Brian


Brian Hafliger
Re: best intake for sbm with w-2 heads [Re: 72340dustermike] #1373537
01/21/13 04:26 PM
01/21/13 04:26 PM
Joined: Jun 2003
Posts: 52,972
Romeo MI
MR_P_BODY Offline
Master
MR_P_BODY  Offline
Master

Joined: Jun 2003
Posts: 52,972
Romeo MI
I like my Indy... I use the 1050 adapter to run
a 1050... runs great to 8200 on my 396ci... I used
it on my 340+ .030 and it pulled hard to 8000 but
that was about the limit on the cam

Re: best intake for sbm with w-2 heads [Re: 72340dustermike] #1373538
01/21/13 09:22 PM
01/21/13 09:22 PM
Joined: Jun 2004
Posts: 1,496
Sask, Can.
7
72demon416 Offline
pro stock
72demon416  Offline
pro stock
7

Joined: Jun 2004
Posts: 1,496
Sask, Can.
As Brian said- the Victor is a good intake for a reasonable price- pretty hard to go wrong with. I ran one for a while and it was a good piece- I would buy it again if I went back to W2's.

Re: best intake for sbm with w-2 heads [Re: 72demon416] #1373539
01/21/13 09:45 PM
01/21/13 09:45 PM
Joined: Jan 2003
Posts: 20,642
So Near, Yet So Far
topside Offline
Too Many Posts
topside  Offline
Too Many Posts

Joined: Jan 2003
Posts: 20,642
So Near, Yet So Far
I have a Holley Strip Dominator on mine (368") but I suppose a newer intake might make a bit more power.

Re: best intake for sbm with w-2 heads [Re: topside] #1373540
01/21/13 10:44 PM
01/21/13 10:44 PM
Joined: Jan 2003
Posts: 482
Marysville Wa
M
moparfan Offline
mopar
moparfan  Offline
mopar
M

Joined: Jan 2003
Posts: 482
Marysville Wa
How much better than the M-1 is the Victor?


2017 Challenger R/T Scat Pack Shaker
2021 T/A 392
1970 Challenger R/T 383,727, 3.55, (Wife's car)
1970 Challenger R/T SE 440-4, 4-speed, 4.10 Dana
1972 Dodge Demon 396 W-2,904, 4.30, 10.660 @ 125.85
2020 Hellcat redeye
Re: best intake for sbm with w-2 heads [Re: moparfan] #1373541
01/22/13 12:30 AM
01/22/13 12:30 AM
Joined: Jun 2004
Posts: 1,496
Sask, Can.
7
72demon416 Offline
pro stock
72demon416  Offline
pro stock
7

Joined: Jun 2004
Posts: 1,496
Sask, Can.
I had both on back to back and while I never got any numbers down with the M1 the victor pulled noticeably harder in the upper rpms.

Re: best intake for sbm with w-2 heads [Re: moparfan] #1373542
01/22/13 12:31 AM
01/22/13 12:31 AM
Joined: Jan 2003
Posts: 5,484
SoCal
Brian Hafliger Offline
master
Brian Hafliger  Offline
master

Joined: Jan 2003
Posts: 5,484
SoCal
Quote:

How much better than the M-1 is the Victor?



Depends on the build...


Brian Hafliger
Re: best intake for sbm with w-2 heads [Re: Brian Hafliger] #1373543
01/22/13 11:25 AM
01/22/13 11:25 AM
Joined: Jun 2010
Posts: 462
Stockholm, Sweden
fed Offline
mopar
fed  Offline
mopar

Joined: Jun 2010
Posts: 462
Stockholm, Sweden
How is the Holley Pro-dominator tunnelram?


Cuda, -70
Valiant-65 AWB,
Valiant Signet200 -65 Topchopped dragcar.
Topolino Fuel Altered.
NostalgiaFED Sold,
SuperComp Bantam Altered, Sold
Ex Harlan Thompsons Nitro funny car American Graffiti Sold,
Re: best intake for sbm with w-2 heads [Re: Brian Hafliger] #1373544
01/22/13 12:26 PM
01/22/13 12:26 PM
Joined: Jan 2003
Posts: 482
Marysville Wa
M
moparfan Offline
mopar
moparfan  Offline
mopar
M

Joined: Jan 2003
Posts: 482
Marysville Wa
Hi Brian, similar build to the orginal poster,11 to 1, hensley stage 2 ported w-2 econo long valve,72 cc open chamber head, the M-1 intake appears to be just gasket matched. the water port from the t-stat housing is blocked as well. 5500 8" converter 4:30 gear. The car has lazy 60' now (1.60 best)3250 lbs.

Mine is 40 over as well, 3.79 stroke. Crane .580" .600" lift, 268, 278 duration @ .050 crane flat tappet cam, Installed at card spec

Last edited by moparfan; 01/22/13 12:34 PM.
Re: best intake for sbm with w-2 heads [Re: moparfan] #1373545
01/22/13 12:42 PM
01/22/13 12:42 PM
Joined: Jun 2003
Posts: 52,972
Romeo MI
MR_P_BODY Offline
Master
MR_P_BODY  Offline
Master

Joined: Jun 2003
Posts: 52,972
Romeo MI
Quote:

Hi Brian, similar build to the orginal poster,11 to 1, hensley stage 2 ported w-2 econo long valve,72 cc open chamber head, the M-1 intake appears to be just gasket matched. the water port from the t-stat housing is blocked as well. 5500 8" converter 4:30 gear. The car has lazy 60' now (1.60 best)3250 lbs.

Mine is 40 over as well, 3.79 stroke. Crane .580" .600" lift, 268, 278 duration @ .050 crane flat tappet cam, Installed at card spec




2 things I would look at... first what RPM are you
leaving at and have you played with the squirters
and pump cams

Re: best intake for sbm with w-2 heads [Re: moparfan] #1373546
01/22/13 01:54 PM
01/22/13 01:54 PM
Joined: Jan 2003
Posts: 5,484
SoCal
Brian Hafliger Offline
master
Brian Hafliger  Offline
master

Joined: Jan 2003
Posts: 5,484
SoCal
Quote:

Hi Brian, similar build to the orginal poster,11 to 1, hensley stage 2 ported w-2 econo long valve,72 cc open chamber head, the M-1 intake appears to be just gasket matched. the water port from the t-stat housing is blocked as well. 5500 8" converter 4:30 gear. The car has lazy 60' now (1.60 best)3250 lbs.

Mine is 40 over as well, 3.79 stroke. Crane .580" .600" lift, 268, 278 duration @ .050 crane flat tappet cam, Installed at card spec




Way too much cam for that combo! I would run something closer to 260@ .050 on a 107 and advance it alot.
Most of my 60ft. I found with CHASSIS and not engine, but that cam is wrong for what your doing.
Brian


Brian Hafliger
Re: best intake for sbm with w-2 heads [Re: fed] #1373547
01/22/13 10:05 PM
01/22/13 10:05 PM
Joined: Feb 2006
Posts: 501
CEDAR RAPIDS
Plymouth340 Offline
mopar
Plymouth340  Offline
mopar

Joined: Feb 2006
Posts: 501
CEDAR RAPIDS
Quote:

How is the Holley Pro-dominator tunnelram?


i have ran the victor,indy and pro dominator tunnelram and the indy was the fastest on my 398 w2 motor

Re: best intake for sbm with w-2 heads [Re: Plymouth340] #1373548
01/22/13 10:32 PM
01/22/13 10:32 PM
Joined: Jun 2003
Posts: 52,972
Romeo MI
MR_P_BODY Offline
Master
MR_P_BODY  Offline
Master

Joined: Jun 2003
Posts: 52,972
Romeo MI
Quote:

Quote:

How is the Holley Pro-dominator tunnelram?


i have ran the victor,indy and pro dominator tunnelram and the indy was the fastest on my 398 w2 motor




I ran the pro dom TR on mine also and the M1 TR..the
M1 was quicker and faster BUT thats apples to oranges
to the single 4bbl intakes

Re: best intake for sbm with w-2 heads [Re: MR_P_BODY] #1373549
01/23/13 11:56 PM
01/23/13 11:56 PM
Joined: Jan 2007
Posts: 3,695
nc
E
emarine01 Offline
master
emarine01  Offline
master
E

Joined: Jan 2007
Posts: 3,695
nc
Does anyone want to take a stab @ where the M1 falls as far as cid and rpm and explain the differences between the M1, victor and Indy and the best applications for each

Re: best intake for sbm with w-2 heads [Re: emarine01] #1373550
01/24/13 12:08 AM
01/24/13 12:08 AM
Joined: Jun 2003
Posts: 52,972
Romeo MI
MR_P_BODY Offline
Master
MR_P_BODY  Offline
Master

Joined: Jun 2003
Posts: 52,972
Romeo MI
I think Brian or someone with a dyno would be best
suited for that... it would eliminate some variables

Re: best intake for sbm with w-2 heads [Re: MR_P_BODY] #1373551
01/26/13 08:43 PM
01/26/13 08:43 PM
Joined: Jan 2007
Posts: 3,695
nc
E
emarine01 Offline
master
emarine01  Offline
master
E

Joined: Jan 2007
Posts: 3,695
nc
Humm... No takers on this one,







Powered by UBB.threads™ PHP Forum Software 7.7.1