Which studs with main girdle? - Moparts Forums

Register Log In Moparts Forums Unlawfl's Race & Engine Tech Which studs with main girdle?

Print Thread

Which studs with main girdle? #2370788 09/14/17 03:53 PM 09/14/17 03:53 PM
Joined: Jul 2005 Posts: 636 Graz, Austria DGS OP mopar
DGS OP mopar Joined: Jul 2005 Posts: 636 Graz, Austria	I got a girdle for cheap but it came without any studs. Which studs do I need to buy to run it? I already have main studs but they are too short. Also which studs for the oil pan? Engine is a 440. thanks

Re: Which studs with main girdle? [Re: DGS] #2370803 09/14/17 04:41 PM 09/14/17 04:41 PM
Joined: May 2011 Posts: 4,489 northern,Ohio,USA C Clanton master
Clanton master C Joined: May 2011 Posts: 4,489 northern,Ohio,USA	Looking at my old ARP box I used 240-5501 with a 3/8" girdle GOTBOOST!New improved with Victor heads. http://www.enginelabs.com/mopar-big-bloc...t-of-necessity/

Re: Which studs with main girdle? [Re: DGS] #2370809 09/14/17 04:54 PM 09/14/17 04:54 PM
Joined: Jul 2005 Posts: 636 Graz, Austria DGS OP mopar
DGS OP mopar Joined: Jul 2005 Posts: 636 Graz, Austria	Thanks! Do you know how long they are? I'd rather buy single studs than a complete kit as I have several nuts and washers lying around.

Re: Which studs with main girdle? [Re: DGS] #2370826 09/14/17 05:41 PM 09/14/17 05:41 PM
Joined: May 2011 Posts: 4,489 northern,Ohio,USA C Clanton master
Clanton master C Joined: May 2011 Posts: 4,489 northern,Ohio,USA	You could put a screw driver in the main hole and measure up to the top of the girdle and add 1" for the nut,washer plus 2 threads.The rear,front dtud are just 1/4" shorter for pan clearence.I will see if I can get to the engine that has those studs in it. GOTBOOST!New improved with Victor heads. http://www.enginelabs.com/mopar-big-bloc...t-of-necessity/

Re: Which studs with main girdle? [Re: DGS] #2370841 09/14/17 05:53 PM 09/14/17 05:53 PM
Joined: May 2011 Posts: 4,489 northern,Ohio,USA C Clanton master
Clanton master C Joined: May 2011 Posts: 4,489 northern,Ohio,USA	I got 1 out and it is 5.250" long with 1 1/4" thread goes into the block and 2" fine thread at the top of the main cap for 2 nuts,washers,girdle.[some shims may be needed] ps:The measurement I gave is for another kit I have no part # but the 1 I gave is for a windage tray also so it has a longer stud that has a stem for the tray. Last edited by Clanton; 09/14/17 08:16 PM. GOTBOOST!New improved with Victor heads. http://www.enginelabs.com/mopar-big-bloc...t-of-necessity/

Re: Which studs with main girdle? [Re: DGS] #2370843 09/14/17 05:55 PM 09/14/17 05:55 PM
Joined: Jul 2005 Posts: 636 Graz, Austria DGS OP mopar
DGS OP mopar Joined: Jul 2005 Posts: 636 Graz, Austria	Awesome! Thanks a lot!

Re: Which studs with main girdle? [Re: DGS] #2370851 09/14/17 06:03 PM 09/14/17 06:03 PM
Joined: May 2011 Posts: 4,489 northern,Ohio,USA C Clanton master
Clanton master C Joined: May 2011 Posts: 4,489 northern,Ohio,USA	no problem GOTBOOST!New improved with Victor heads. http://www.enginelabs.com/mopar-big-bloc...t-of-necessity/

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1