Previous Thread
Next Thread
Print Thread
Page 2 of 3 1 2 3
Re: putting hood on car alone [Re: cornet684me] #993349
05/16/11 11:48 PM
05/16/11 11:48 PM
Joined: Dec 2007
Posts: 1,639
Brandon, Ms
C
cornet684me Offline OP
top fuel
cornet684me  Offline OP
top fuel
C

Joined: Dec 2007
Posts: 1,639
Brandon, Ms
wow, thanks for all the input, i am still trying to find 2 strong guys to help me, i may do the body shop install, i do have a couple of body shops around, however, this takes all the fun out, i have done the complete car, i will post my results asap



Re: putting hood on car alone [Re: cornet684me] #993350
05/17/11 01:02 AM
05/17/11 01:02 AM
Joined: Jan 2003
Posts: 7,798
Lyons, CO
MileHighDart Offline
master
MileHighDart  Offline
master

Joined: Jan 2003
Posts: 7,798
Lyons, CO
Not only did I install my GTS hood by myself, I did it with one arm tied behind my back,,, well almost. My right arm was in a sling, I had recently had rotator cuff surgery.

I attached a block n tackle to the rafters, attached it to the hood latch on the front of the hood. Hoisted it up off the ground and tied it off.
Then I took 2 motorcycle type tie down straps and attached them to the rafters about where the back of the hood would be. I hooked them on the back edge of the hood and raised them alternately back and forth till I had the hood hanging flat about eye level.
Then I drove the car under the hood, started lowering the straps on the back of the hood till I had the hood at the correct angle to bolt to the hinges. Adjusted the straps a little more, then lined up the holes and bolted it on.
Once it was bolted on tight I removed the straps and the block n tackle.
I got the alignment fairly close, at least so I could close and latch the hood. But I did have to wait a few months to do the final alignment cause I couldn't figure out how to do that part with one arm.

6637171-S5002390.JPG (58 downloads)
Re: putting hood on car alone [Re: Challenger 1] #993351
05/17/11 02:11 AM
05/17/11 02:11 AM
Joined: Jan 2003
Posts: 9,100
Tucson, AZ
Ramrod39 Offline
My New Title
Ramrod39  Offline
My New Title

Joined: Jan 2003
Posts: 9,100
Tucson, AZ
Quote:

Quote:

Hoods are overrated ...go hoodless




So are bra's.




I agree. I never wear a bra.

Re: putting hood on car alone [Re: Ramrod39] #993352
05/17/11 02:33 AM
05/17/11 02:33 AM
Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
1_WILD_RT Offline
Management Trainee
1_WILD_RT  Offline
Management Trainee

Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
Quote:

Quote:

Quote:

Hoods are overrated ...go hoodless




So are bra's.




I agree. I never wear a bra.




Glad to hear it..


"The Armies of our ancestors were lucky, in that they were not trailed by a second army of pencil pushers."
Re: putting hood on car alone [Re: MileHighDart] #993353
05/17/11 03:13 AM
05/17/11 03:13 AM
Joined: Dec 2010
Posts: 12,375
SoCal
MuuMuu101 Offline
I got lucky at Woodward!
MuuMuu101  Offline
I got lucky at Woodward!

Joined: Dec 2010
Posts: 12,375
SoCal
Quote:

Not only did I install my GTS hood by myself, I did it with one arm tied behind my back,,, well almost. My right arm was in a sling, I had recently had rotator cuff surgery.

I attached a block n tackle to the rafters, attached it to the hood latch on the front of the hood. Hoisted it up off the ground and tied it off.
Then I took 2 motorcycle type tie down straps and attached them to the rafters about where the back of the hood would be. I hooked them on the back edge of the hood and raised them alternately back and forth till I had the hood hanging flat about eye level.
Then I drove the car under the hood, started lowering the straps on the back of the hood till I had the hood at the correct angle to bolt to the hinges. Adjusted the straps a little more, then lined up the holes and bolted it on.
Once it was bolted on tight I removed the straps and the block n tackle.
I got the alignment fairly close, at least so I could close and latch the hood. But I did have to wait a few months to do the final alignment cause I couldn't figure out how to do that part with one arm.




Amazing hood! Where did you get it from? Did it come with the inserts?

Re: putting hood on car alone [Re: cornet684me] #993354
05/22/11 11:42 PM
05/22/11 11:42 PM
Joined: Dec 2007
Posts: 1,639
Brandon, Ms
C
cornet684me Offline OP
top fuel
cornet684me  Offline OP
top fuel
C

Joined: Dec 2007
Posts: 1,639
Brandon, Ms
update********i just got the hood on my car, by myself, thanks to my engine hoist and a little patiences****


6646228-002.JPG (130 downloads)
Re: putting hood on car alone [Re: cornet684me] #993355
05/22/11 11:48 PM
05/22/11 11:48 PM
Joined: Nov 2004
Posts: 6,653
Near Reading PA USA
pinkduster Offline
master
pinkduster  Offline
master

Joined: Nov 2004
Posts: 6,653
Near Reading PA USA
There is NO WAY I would risk my paint job or my back by putting a hood on by myself. I'd just call a friend for some help.

Re: putting hood on car alone [Re: cornet684me] #993356
05/22/11 11:49 PM
05/22/11 11:49 PM
Joined: Dec 2007
Posts: 1,639
Brandon, Ms
C
cornet684me Offline OP
top fuel
cornet684me  Offline OP
top fuel
C

Joined: Dec 2007
Posts: 1,639
Brandon, Ms
the only problem i am having is getting the hood to line up, got new hinges from AMD, i get the hood to close however, the back of the hood will not close, it is sticking up on both sides


6646236-003.JPG (95 downloads)
Re: putting hood on car alone [Re: cornet684me] #993357
05/23/11 12:13 AM
05/23/11 12:13 AM
Joined: Nov 2003
Posts: 36,040
Lincoln Nebraska
R
RapidRobert Offline
Circle Track
RapidRobert  Offline
Circle Track
R

Joined: Nov 2003
Posts: 36,040
Lincoln Nebraska
loosen the bolts just enough so you can pushdown on the rear on both sides (hire that homeless guy) & have it stay in that position then tighten the bolts then shut it keeping tabs on the rear fit/interference. PATIENCE. Repeat as needed & go easy as you're almost there & dont need a mistake (scratched paint) at this junction


live every 24 hour block of time like it's your last day on earth
Re: putting hood on car alone [Re: RapidRobert] #993358
05/23/11 12:16 AM
05/23/11 12:16 AM
Joined: Dec 2007
Posts: 1,639
Brandon, Ms
C
cornet684me Offline OP
top fuel
cornet684me  Offline OP
top fuel
C

Joined: Dec 2007
Posts: 1,639
Brandon, Ms


i think i will let it sit for couple of days to give me time to take it all in, my patiences are running thin

thanks Robert


Re: putting hood on car alone [Re: MuuMuu101] #993359
05/23/11 12:56 AM
05/23/11 12:56 AM
Joined: Jan 2003
Posts: 7,798
Lyons, CO
MileHighDart Offline
master
MileHighDart  Offline
master

Joined: Jan 2003
Posts: 7,798
Lyons, CO
Quote:

Quote:

Not only did I install my GTS hood by myself, I did it with one arm tied behind my back,,, well almost. My right arm was in a sling, I had recently had rotator cuff surgery.

I attached a block n tackle to the rafters, attached it to the hood latch on the front of the hood. Hoisted it up off the ground and tied it off.
Then I took 2 motorcycle type tie down straps and attached them to the rafters about where the back of the hood would be. I hooked them on the back edge of the hood and raised them alternately back and forth till I had the hood hanging flat about eye level.
Then I drove the car under the hood, started lowering the straps on the back of the hood till I had the hood at the correct angle to bolt to the hinges. Adjusted the straps a little more, then lined up the holes and bolted it on.
Once it was bolted on tight I removed the straps and the block n tackle.
I got the alignment fairly close, at least so I could close and latch the hood. But I did have to wait a few months to do the final alignment cause I couldn't figure out how to do that part with one arm.




Amazing hood! Where did you get it from? Did it come with the inserts?




Its an AMD reproduction hood. I got it from a member here, JSBROWN, or Jeff Brown. He sells AMD sheet metal and other stuff and was near where I live. Good guy, easy deal and I wasn't in a hurry so he waited till he had another local order and shipped them together, saved me half the shipping cost.
And No it didn't come with the inserts. They are repo's too, got them off ebay from classic industries.(straight from china), but the look real nice.

Re: putting hood on car alone [Re: cornet684me] #993360
05/23/11 02:45 AM
05/23/11 02:45 AM
Joined: Apr 2010
Posts: 10,570
Sunny South Florida
Golden-Arm Offline
I Live Here
Golden-Arm  Offline
I Live Here

Joined: Apr 2010
Posts: 10,570
Sunny South Florida
i do it on the dakota and full size, anytime i need to work on the back side of the motor. i lift the hood open, and get a board to hold the front up, in the center. i get a couple of towels, and fold them, and place one under each rear corner of the hood across the cowl, to the hinge, and fender. use a sharpie, and trace around the hinge where it bolts to hood. loosen all bolts. remove one side completely, and hold the hood, and after the last bolt comes out, guide it onto the towel, so it sits on the corner of the hood. (you folded the towel, so it's protected) repeat for other side. hood is now free, and supported by board up front. lift hood from board, and grab it where it's easiest for you to balance, and lift it off, and place it wherever.

to reinstall, place some folded towels on cowl, at hinge and cover fenders. lay a board of proper length on the rad support. lift hood into position, and lay it in the closed position on the vehicle. once in position, lift the front, and insert the board when it's high enough to hold hood open, in proper position. working either side, install one bolt, and screw it about halfway in. switch sides, and install all bolts on hood, make them hand tight. go to first side and finish installing. align hood with marks,and tighten. finish other side. close carefully, and check clearances. have fun!!


"When Tyranny Becomes Law, Rebellion Becomes Duty"

Re: putting hood on car alone [Re: cornet684me] #993361
05/23/11 08:23 AM
05/23/11 08:23 AM
Joined: Sep 2004
Posts: 22,873
Chicken coop
dustergirl340 Offline
Chicken Little
dustergirl340  Offline
Chicken Little

Joined: Sep 2004
Posts: 22,873
Chicken coop
You guys need more friends.

Re: putting hood on car alone [Re: cornet684me] #993362
05/24/11 10:02 AM
05/24/11 10:02 AM
Joined: Dec 2009
Posts: 1,023
pa.
D
dan9 Offline
super stock
dan9  Offline
super stock
D

Joined: Dec 2009
Posts: 1,023
pa.
I would loosen all bolts except the rear closest to the firewall and lift the hood as high as it will go.Tighten the frontmost bolts then slowly close it and see if it helped, the hood just needs rocked so to speak.

Re: putting hood on car alone [Re: cornet684me] #993363
05/25/11 11:31 PM
05/25/11 11:31 PM
Joined: Dec 2007
Posts: 1,639
Brandon, Ms
C
cornet684me Offline OP
top fuel
cornet684me  Offline OP
top fuel
C

Joined: Dec 2007
Posts: 1,639
Brandon, Ms
took about 2 1/2 hours and alot of gray hair, but i think i got it, still a wee bit high in the rear, but i think it will settle down, the new springs are really tight, thanks for all the input!




6651266-resizehood1.jpg (92 downloads)
Re: putting hood on car alone [Re: cornet684me] #993364
05/25/11 11:32 PM
05/25/11 11:32 PM
Joined: Dec 2007
Posts: 1,639
Brandon, Ms
C
cornet684me Offline OP
top fuel
cornet684me  Offline OP
top fuel
C

Joined: Dec 2007
Posts: 1,639
Brandon, Ms
driver's side a wee bit high, i scare to touch it though

6651269-resizehood2.jpg (193 downloads)
Re: putting hood on car alone [Re: cornet684me] #993365
05/25/11 11:34 PM
05/25/11 11:34 PM
Joined: Dec 2007
Posts: 1,639
Brandon, Ms
C
cornet684me Offline OP
top fuel
cornet684me  Offline OP
top fuel
C

Joined: Dec 2007
Posts: 1,639
Brandon, Ms
another

6651274-resizehood2.jpg (267 downloads)
Re: putting hood on car alone [Re: cornet684me] #993366
05/25/11 11:36 PM
05/25/11 11:36 PM
Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
1_WILD_RT Offline
Management Trainee
1_WILD_RT  Offline
Management Trainee

Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
Copied from Resto Rick's site.... I know it sez E body & 71 & up B but it will help your car too...

A common alignment problem on E-body & 71-up B-bodies is the rear edge being up too high with the hinges being adjusted all the way down on the inner fender.
This is an adjustment problem! Start by moving the hinge up on the inner fender. (yes, up!)
Then, loosen the 2 rear bolts and leave the front bolt snug. Now lift the hood to make the hinge rotate (as viewed from the side). Retighten the rear bolts and check the fit. This procedure will get that tail to come down. Adjust the front-to-rear dimension on the hood side bolts.
It can be frustrating and take some time, but these hoods will fit correctly! I’ve installed them with the hood sitting about 2 1/2" above the fender! Within a few minutes it was fitting perfect!


"The Armies of our ancestors were lucky, in that they were not trailed by a second army of pencil pushers."
Re: putting hood on car alone [Re: cornet684me] #993367
05/25/11 11:36 PM
05/25/11 11:36 PM
Joined: Dec 2007
Posts: 1,639
Brandon, Ms
C
cornet684me Offline OP
top fuel
cornet684me  Offline OP
top fuel
C

Joined: Dec 2007
Posts: 1,639
Brandon, Ms
okay, got the right size now

6651279-resizehood2.jpg (178 downloads)
Re: putting hood on car alone [Re: 1_WILD_RT] #993368
05/25/11 11:38 PM
05/25/11 11:38 PM
Joined: Dec 2007
Posts: 1,639
Brandon, Ms
C
cornet684me Offline OP
top fuel
cornet684me  Offline OP
top fuel
C

Joined: Dec 2007
Posts: 1,639
Brandon, Ms
thanks Randy,

i think i will wait couple of days and get my nerve back up and will try to fine tune the hood, that is exactly what is wrong with my hood, the back of the hood just a hair too high,


Page 2 of 3 1 2 3






Powered by UBB.threads™ PHP Forum Software 7.7.1