what would be the code for a 70 charger w/ the V21 and 440 call outs? I'm going to do that on my 70 no vinyl, sublime car..too much green..

another seldom seen V21

yes, but seldom seen in my neck of the woods

Ken: Do you have any pics of 71 Challengers with V21 striping? If you do could you post them please! Are you going to Carlisle?

I'm sure I do Dwight. Is there something special you are looking for? I have seen them with and without the R/T cutout, but I thought they all were supposed to have them. But I'm not really up on my '71s.

As for Carlisle, I wasn't planning on going, but as the time gets closer I find that I'd really like to go. It's the only time I get see guys like you, Dan, Barry and whomever else I might be missing.

1972 340 V21 option

In 72 you could order the V21, Performance Hood Treatment, the original owner of this Duster did just that....Also there were a few 340 Twisters built...they were for export only though, mainly to Canada. This decal was rolled up in the glove box upon delivery and installed by the original owner. The selling dealer was supposed to do this during prep, frustrated over it upon pickup he told them, "I'll just do it myself". This car was special ordered, check the code Y14 for sold car.........Dave

Just in case you did not know, that is not an original window sticker.

on the 70 Challengers, were any of the V21 hood treatments painted on and how many different ways were those hoods blacked out?

The new V21 Performance Hood Treatment

mine was optioned the same, only red

From the Cyber Cuda web page CYBER CUDA



KEY:

A = 20" UP from hood edge (nose side). 9 5/16" between red areas
B = 39" UP from hood edge (nose side). 9 9/16" between red areas
C = from bottom vent corner (passenger side vent hole; hole closest to middle of hood). 11 1/4" to red
D = 11 1/4" from hood lip (windshield side) to red. ** (Align togther with point 'C')
E = 9 3/16" hood lip (windshield side), going over 6th vent (from center of hood) hole
F = 9 10/16" hood lip (windshield side), going over 13th vent (from center of hood) hole
G = 10 10/16" hood lip (windshield side), going over 5th vent (from driver's side fender) hole
H = 15 3/4" from CORNER of hood lip (windshield side) to red ** (align together with point 'I')
I = 46" up from hood edge (nose side). 9 1/4" IN from hood edge (driver's side fender edge)
J = 36" UP from hood edge (nose side). 6 15/16" from edge to red
K = 25" UP from hood edge (nose side). 6 13/16" from edge to red
L = 13" UP from hood edge (nose side). 6 13/16" from edge to red
M = AT hood edge (nose side). 6 11/16" from edge to red

1 = 4" UP from hood edge (nose side). 6 11/16 from edge to red
2 = 21 1/4" - from edge to far side of first 'red' scallop
3 = 30 9/16" - from edge to near side of 2nd 'red' scallop (not pictured)
4 = 45 10/16" - from edge to far side of 2nd 'red' scallop (not pictured)
5 = 52 1/8" - total width of hood from driver's side to passenger side (not pictured)

# 3,4 & 5 are not shown on picture, but would be a continuation of the line between
points #1 & #2. This 'line' was measured starting at 4" above the hood egde (nose side)

Again from the Cyber Cuda web page



OUTSIDE AREAS (from outside edge of hood to 'red' scallops)
* = 7" wide at 40" UP from the front edge of the hood (closest to the nose). This is between the outer edge of the hood (on both driver & passenger sides) and the edge of the red scallops (just before the scallop curve begins).

6 11/16" wide measurement is at the front egde of the hood (closest to the nose of the car).

CENTER SECTION (between the scallops)
9 1/8" wide at 4" UP from the front edge of hood (closest to nose)

9 5/16" wide at 20" UP from the front edge of the hood (closest to the nose of the car).

9 9/16" wide at 39" UP from the front edge of the hood (closest to the nose of the car).