Previous Thread
Next Thread
Print Thread
driveshaft length?? #361854
06/29/09 06:56 PM
06/29/09 06:56 PM
Joined: Jan 2003
Posts: 1,271
eastern long island,NY
JeepJimmy Offline OP
pro stock
JeepJimmy  Offline OP
pro stock

Joined: Jan 2003
Posts: 1,271
eastern long island,NY
I thought there was a chart in the tech section? 68 Dart 273, 2 door, 904, 8/3/4. I think the one i got for the car is too long. any ideas? on lengths?


70 duster 360magnum, 1975 jeep j-10.
Re: driveshaft length?? [Re: JeepJimmy] #361855
06/29/09 07:01 PM
06/29/09 07:01 PM
Joined: Dec 2007
Posts: 18,153
Mass
DAYCLONA Offline
I Live Here
DAYCLONA  Offline
I Live Here

Joined: Dec 2007
Posts: 18,153
Mass
.

5322618-driveshaftc.JPG (80 downloads)
Re: driveshaft length?? [Re: DAYCLONA] #361856
06/29/09 07:02 PM
06/29/09 07:02 PM
Joined: Dec 2007
Posts: 18,153
Mass
DAYCLONA Offline
I Live Here
DAYCLONA  Offline
I Live Here

Joined: Dec 2007
Posts: 18,153
Mass
2

5322622-driveshaft2.JPG (75 downloads)
Re: driveshaft length?? [Re: DAYCLONA] #361857
06/29/09 07:07 PM
06/29/09 07:07 PM
Joined: Jan 2003
Posts: 1,271
eastern long island,NY
JeepJimmy Offline OP
pro stock
JeepJimmy  Offline OP
pro stock

Joined: Jan 2003
Posts: 1,271
eastern long island,NY
Awesome!!! looks like 48.6 and i would assume thats center of U joint to center of U joint?


70 duster 360magnum, 1975 jeep j-10.
Re: driveshaft length?? [Re: JeepJimmy] #361858
06/29/09 09:05 PM
06/29/09 09:05 PM
Joined: Apr 2005
Posts: 12,271
Overpriced Housing Central
RobX4406 Offline
I Live Here
RobX4406  Offline
I Live Here

Joined: Apr 2005
Posts: 12,271
Overpriced Housing Central
I don't see a single 111" wheelbase A body on either of those tables.

Should be closer to 51.50-52"

https://board.moparts.org/ubbthreads/upload2/4563759-PartNoDriveshafts.pdf

Re: driveshaft length?? [Re: RobX4406] #361859
06/29/09 09:32 PM
06/29/09 09:32 PM
Joined: Nov 2003
Posts: 36,040
Lincoln Nebraska
R
RapidRobert Offline
Circle Track
RapidRobert  Offline
Circle Track
R

Joined: Nov 2003
Posts: 36,040
Lincoln Nebraska
Since you have one in hand I would put it all the way in the trans(w springs loaded) & measure the C to C(subtract 3/4") which'll be the ideal length you need if you do end up having it cut rather than getting a different one plus you will have the correct dimention in hand in case the chart info is wrong(like the housing chart dimentions is said to be(wrong)on some of em.


live every 24 hour block of time like it's your last day on earth






Powered by UBB.threads™ PHP Forum Software 7.7.1