Page 1 of 6 1 2 3 4 5 6 >
Topic Options
#2557548 - 10/02/18 09:31 AM For Sale - Big Block Engine - 4th Quarter
moparts Offline


Registered: 01/19/03
Posts: 14163
Loc: Norwich CT USA
up

Top
#2557584 - 10/02/18 10:09 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
Goat330 Offline
mopar

Registered: 11/22/07
Posts: 412
Loc: Randolph, Ohio--N.E. Ohio
Indy(wedge) cross-ram(NIB),never used it on my project,and (NIB) 750 Edelbrock Performer carb(just one,not 2)+ strip kit for carb. The manifold has the offset mounting not the inline mounts.Will sell all of the above for $1250+ shipping.I would also consider trading for a factory cross ram intake(wedge)don't bug me trying to unload your overpriced intakes for hemi,Bill at wmemore@aol.com or PM. Thank you for free ads Moparts

Here's a link to that photo.
http://s846.photobucket.com/user/Bigemo63/media/102_0367.jpg.html




Edited by Goat330 (10/02/18 12:07 PM)

Top
#2557606 - 10/02/18 10:30 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
modelmakerinc Offline
top fuel

Registered: 01/20/03
Posts: 2043
Loc: west palm beach, florida
440Source distributor for low block, 383/400

Looks almost new was on an engine that is going to upgrade to MSD.

Distributor only $70 obo, shipped to the lower48.

Pm here, text 561.906.0480 email modelmakerinc@att.net


Attachments
20181001_183132.jpg

20181001_183202.jpg




Edited by modelmakerinc (10/02/18 10:33 AM)
_________________________
Exceptional Architectural, Yacht and Automotive scale models. e-mail modelmakerinc@att.net for a portfolio review. www.modelmakerinc.com

Top
#2557626 - 10/02/18 11:16 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
6PAX Offline
master

Registered: 01/20/03
Posts: 4562
Loc: Metro Detroit
Cal Custom El Toro air cleaner wing nut. $5

Used chrome thermostat housing. $5

Used Crane cam #278-2. Cam only, no lifters. $75

Four new extra wide chrome valve cover hold down clamps. $10 for the set

New exhaust manifold heat stove to air cleaner hose. $20

Cal Custom 14" aluminum air cleaner with filter. $100

1970 Single nipple oil breather with hose. $35

New 12" oval 4 barrel aluminum air cleaner with filter. It measures 12" L x 8 1/4" W x 3" H and has a 5 1/8" carb opening. $60

NOS Direct Connection big block double roller timing chain #P4120264. $75

Cal Custom 9" finned air cleaner top and base. No filter. $75

Mr. Gasket 1" thick carb spacer. $15

137 Spectre brand radiator and heater hose clamp covers. Some chrome, some red and some blue anodized. Various sizes. $50 for the lot.

NOS STR-15 383-400 crossram intake manifold with linkage. $2750

1972 400 parts. Oil pump $5, various AC brackets $50 for the lot, spark plug shields $10 pair, exhaust manifold heat stove for non-hp manifolds (needs a little straightening) $15. $50 for everything.

Carb. throttle linkage pin. $10

Used black Mopar Performance aluminum valve covers. $90

Big block flywheel part #2843214 143 tooth. $50

Pair of big block exhaust manifolds. Part numbers 3830800 & 3830820. $100

Pair of big block exhaust manifolds. Part numbers 2532626 & 2532464. $80

Pair of big block heads. Part number 2406516. $100

Alternator date coded 1965. $60

1969 B-body 4 bbl. air cleaner top. $200

1967 440 HP intake manifold #2806178. Media blasted and primed. $100

Prices do not include shipping. gt340 @ yahoo.com


Edited by 6PAX (11/11/18 09:50 PM)

Top
#2558143 - 10/03/18 08:38 AM Re: QFT/Proform-type "950" 1.45" v 4150 Carb [Re: moparts]
johnnyd Offline
member

Registered: 12/14/11
Posts: 112
Loc: Boston, MA
roller rocker arms for the Brodix B1/BS head. The rockers are the original rockers that came with my B1BS heads. One rocker has minor damage from a push rod cup. I spoke with Scott at Koffel's Place about the damage and he said it was fine to run. $400

More pics here: https://boston.craigslist.org/sob/pts/d/big-block-mopar-mopar-roller/6720476197.html


Attachments
B1BS_rockers_01a.JPG




Edited by johnnyd (10/12/18 11:39 AM)

Top
#2558144 - 10/03/18 08:39 AM 440 main caps [Re: moparts]
johnnyd Offline
member

Registered: 12/14/11
Posts: 112
Loc: Boston, MA
440 main caps from my cracked block ***SOLD!*** thanks Moparts!


Edited by johnnyd (10/16/18 09:35 AM)

Top
#2558145 - 10/03/18 08:43 AM Mopar 440 bottom end plus more eagle, crane, indy [Re: moparts]
johnnyd Offline
member

Registered: 12/14/11
Posts: 112
Loc: Boston, MA
My stupidity is your gain. I left a little water in my motor last winter and it was enough to crack my block. I'm thus selling the internals plus a bit more. I have a forged crank, eagle h-beam rods, 13.5:1 BRC .030 pistons all balanced. I'm including the gear drove, Crane .543/.561 roller cam, and Crane Roller lifters. Also include Indy 440-2 intake, Indy valley plate, and pushrods that work on a 440-1 head. Just machine a block, use your heads, install new bearings (rings if you want) and you're good to go. ~50 runs on this bottom end. $2500

pics https://boston.craigslist.org/sob/pts/d/mopar-440-bottom-end-plus/6720476086.html


Attachments
440_01a.JPG




Edited by johnnyd (10/12/18 11:40 AM)

Top
#2558243 - 10/03/18 12:02 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
luckydave Offline
master

Registered: 01/01/06
Posts: 3858
FACTORY BIG BLOCK ROCKER ARM SETS 4 OF THEM
Great condition

Four sets ---of big block factory hydraulic rocker arms with all spacers and enough hold downs for the lot-- The repo units are China junk and are too narrow and Chatter like crazy--Don't be fooled by them-- use stockers

$50 plus whatever UPS is to you
emails only please dusterdave173@gmail.com


Attachments
OCT ADS#### 003.JPG

Description: 2




Edited by crabman173 (11/17/18 09:43 AM)

Top
#2558244 - 10/03/18 12:03 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
luckydave Offline
master

Registered: 01/01/06
Posts: 3858
REAR MAIN SEAL HOLDERS
TWO USED REAR SEAL HOLDERS WITH BOLTS
$29 shipped free dusterdave173@gmail please email no PM's Thanks


Attachments
OCT ADS#### 005.JPG

Description: 4



Top
#2558245 - 10/03/18 12:05 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
luckydave Offline
master

Registered: 01/01/06
Posts: 3858
NICE set 383-400 main caps off 400 block $35 shipped free
dusterdave173@gmail.com Thanks


Attachments
199527_412403788821793_33094216_n[1].jpg



Top
#2558251 - 10/03/18 12:16 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
luckydave Offline
master

Registered: 01/01/06
Posts: 3858
BIG BLOCK HEAD BOLTS WOW!!
I will ship as many as will fit into a medium flat rate box ( 70 lb limit) the tape will cost more than the shipping so....
enough to last you a life time and help on those resto's where you want a matching set correct for your build
$55 shipped FREE!!!! email only dusterdave173@gmail.com


Attachments
BOLTS 001.JPG

Description: 4




Edited by crabman173 (10/03/18 12:29 PM)

Top
#2558252 - 10/03/18 12:17 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
luckydave Offline
master

Registered: 01/01/06
Posts: 3858
The Good big block water pump housings I have three
$30 each shipped free!!!!! dusterdave173@gmail.com Thanks


Attachments
BOLTS 003.JPG

Description: 2



Top
#2558259 - 10/03/18 12:26 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
luckydave Offline
master

Registered: 01/01/06
Posts: 3858
Big Block and Small Block
LOT of rocker adjusters and nuts--great spares!!!! Some of everything Harland, Indy, Crane etc get them all $50 shipped FREE dusterdave173@gmail.com


Attachments
SPACE 001.JPG

Description: 7




Edited by crabman173 (10/03/18 12:28 PM)

Top
#2558459 - 10/03/18 03:41 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: Joesixpack]
Joesixpack Offline
I Live Here

Registered: 01/21/03
Posts: 10956
Loc: APACHE JUNCTION AZ
WILL NOT FIT ANY 1965 DODGE POLARA, MONACO,OR CHRYSLER 300

NEW USA MADE ENGINE MOUNTING BRACKETS(MOTOR MOUNTS)

THESE ARE THE ENGINE MOUNTING BRACKETS THAT BOLT TO THE EARS OF YOUR ENGINE BLOCK

THEY ARE EXACT DUPLICATES OF THE FACTORY BIG BLOCK MOUNTS

THEY INCLUDE GRADE 8 ATTACHING BOLTS, NUTS, WASHERS

THEY ARE POWDERCOATED SEMI GLOSS BLACK

THEY ARE BRAND NEW!

THEY WILL FIT ALL V8 K-FRAMES (WONT FIT 6 CYL KFRAMES)

FIT

1963-1964 DODGE POLARA,330/440 MODELS WITH AN ORIGINAL V8 K-FRAME

1965 DODGE CORONET WITH A V8 K-FRAME

WONT FIT ANY 66 AND UP B-BODY KFRAME

WONT FIT ANY 1965 DODGE POLARA OR MONACO

YES 273-318S USE THE SAME K-FRAME AS THE 361-383-413-426WS

$90 plus $14 usps medium flat rate box
cowgerwilliam035@gmail.com


Attachments
6365b413 004.JPG

6365b413 007.JPG

6365b413 006.JPG

6365b413 003.JPG



Top
#2558511 - 10/03/18 04:30 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: Joesixpack]
Joesixpack Offline
I Live Here

Registered: 01/21/03
Posts: 10956
Loc: APACHE JUNCTION AZ
2 NEW big block v8 distributor mounting plates,electronic ignition magnetic pick ups W/HARNESS&PLUG, 2 reluctor wheels,2 locating pins,1 shim, made in the usa nors
PICS WONT LOAD TOO BIG EMAIL ME FOR PICS
$50 mailed
cowgerwilliam035@gmail.com


Edited by Joesixpack (10/04/18 10:05 AM)

Top
#2558541 - 10/03/18 05:53 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
bbodee Offline
member

Registered: 07/03/11
Posts: 26
Loc: CA
NEW BCR 1/2 inch Girdle kit, SOLD thanks Moparts

Used MSD 8536 distributor Sold thanks Moparts

Brand new, not in box, Howards timing set billet steel #94340. Sold

Chrome, made in USA Mopar P4120534 ignition control unit. SOLD. Thanks Moparts

Please feel free to ask for any additional pics/info. Thanks for the ad Moparts




Edited by bbodee (10/12/18 08:30 PM)

Top
#2558863 - 10/04/18 10:45 AM Fresh 540 Mega Block 800 plus hp $17500/obo [Re: moparts]
440PURSUIT Offline
pro stock

Registered: 12/17/04
Posts: 1418
Loc: DC, MD Suburbs
Just Freshened
https://www.youtube.com/watch?v=LqSwun-xYEU

14:1 JE Pistons
Total Seal 1/16 1/16 3/16 File Fit Moly
BME Rods 7.10 426 Forgings
Mopar Mega Block 4.380 bore
Block CNC Machined for lightening. No Motor mounts
4.500 Stroke Eagle
O Ringed -Copper Gaskets
Indy 572-13
Jesel Rockers 1.7
Spray Bar Indy Valve Covers
Cam Motion Solid Roller
R2826-2862-11 281/290 799/750 107/115 lobe Center intalled at 108
Super Damper
Double Roller Chain
Dual Line Milodon Swinging Pickup
8 Bolt Crank with BM Flexpalte
Drilled for Chevy Starter
Indy 4500 Intake

CSI Starter
Motor Plate/Mid Plate
MSD ProBillet

http://s1036.photobucket.com/user/mp440/library/540%20Race?sort=3&page=1

$17500/ offers trades


Attachments
540 Moparts.jpeg




Edited by 440PURSUIT (10/22/18 07:13 PM)
_________________________
1969 Hemi Charger R/T,
1969 Charger RT Clone
1969 Charger Pro Tour Project
1971 Barracuda Convert
1970 440 6pack Superbird,
1968 Fury I Police Pursuit 440 Super Commando 2 door sedan (Black/Blue)
1969 Dart GTS 340 Convert
1967 Barracuda Convert
1968 Barracuda Coupe
1972 Road Runner 340-4
1972 Charger Rallye 400-4
1972 Charger w 383
1972 Sebring Plus 440-6 Clone
1967 A100
1969 Coronet Pro Street
2009 Challengeer SRT8 stick
2006 Dodge Magnum 5.7
2017 3500 Dually

Top
#2559445 - 10/05/18 12:48 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
Slap Shot Offline
top fuel

Registered: 11/03/03
Posts: 1652
Loc: Dover,Pa
sold

Top
#2559571 - 10/05/18 04:01 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
AndyF Online   content
Too Many Posts

Registered: 01/20/03
Posts: 25180
Loc: Oregon
SOLD - BB rod bearings. Standard size. New in box but been sitting on the shelf for a few years. $30 for the set of 8 plus shipping. PayPal preferred. PM me on the board.


Attachments
DSC_3019 (Large).JPG




Edited by AndyF (10/26/18 03:18 PM)

Top
#2559873 - 10/06/18 11:39 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
furious70 Offline
top fuel

Registered: 11/30/06
Posts: 1609
Loc: IL
9/25/69 HP 383 shortblock $350obo

bare magged 452 castings, $100

mallory yc-365-hp distributor $50

in eastern Iowa but can get to Chicago


Attachments
IMG_0767.JPG

IMG_0769.JPG

IMG_0705.JPG




Edited by furious70 (10/06/18 11:41 AM)

Top
#2559874 - 10/06/18 11:42 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
furious70 Offline
top fuel

Registered: 11/30/06
Posts: 1609
Loc: IL
Two early 1972 440 blocks and caps, no VIN's or upper pad stampings. I measured them both at .006-.010 wear from standard but I am no machinist. $500obo each

in eastern Iowa but can get to Chicago


Attachments
180804_034353_12.jpeg

180804_034354_17.jpeg

20180825_131449.jpg

20180825_131443.jpg




Edited by furious70 (10/06/18 11:42 AM)

Top
#2559878 - 10/06/18 11:44 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
furious70 Offline
top fuel

Registered: 11/30/06
Posts: 1609
Loc: IL
MP distributor 383/400 elec 3690431 $50
375518 1974 440HP distributor $75
3656344 1972 440 distributor $50
2875715 prestolite 69 383 dual point distributor $150
aluminum dual point 383 distributor (no tag) $50


Attachments
2875715dualpt.jpg

IMG950735 - Copy.jpg

IMG_0693.JPG

IMG_0689 (1).JPG



Top
#2559939 - 10/06/18 02:53 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: furious70]
Joesixpack Offline
I Live Here

Registered: 01/21/03
Posts: 10956
Loc: APACHE JUNCTION AZ
YOUR BUYING 5 NORS MADE IN THE USA NIEHOFF AL-43 HEAVY DUTY DUAL POINT IGNITION ROTORS ,WILL FIT 361-383-413-426W-426H-440+6 DODGE,PLYMOUTH,CHRYSLER

CAST IRON FACTORY DUAL POINT DISTRIBUTORS&DC,MP MECHANICAL ADVANCE RACE DISTRIBUTORS


$50 MAILED
cowgerwilliam035@gmail.com
paypal or money order


Attachments
al43 001.JPG

al43 002.JPG



Top
#2560378 - 10/07/18 01:07 PM 440 pistons rods crank [Re: moparts]
RATPATROL Offline
enthusiast

Registered: 02/21/04
Posts: 226
Loc: mi
440 +030 Ross pistons (99539) 990 pin 6.76 eagle h-beam rods, oem .010 under steel crankshaft. Very little run time on this rotating assembly all balanced and ready to go . $1200. Call if interested. 586 7096113


Attachments
440 3.JPG

440 2.JPG




Edited by RATPATROL (10/07/18 01:20 PM)

Top
#2560399 - 10/07/18 02:16 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
lancer493 Offline
member

Registered: 01/14/13
Posts: 36
77 440 truck block,thick main web. Bored and honed to 4.350".BCR aluminum main caps,girdle,and ARP studs installed,line bored and honed.Hot tanked and magnafluxed.$1400 worth of machine work all performed by Nelson Competition in Pinellas Park ,Fl.Never used or assembled. My loss,your gain.You finish.$1950.00 Prefer local pick up. Tampa Bay Fl.area. pm me here for more info.I have receipt for machine work. thanks, Bill

Top
#2562418 - 10/11/18 11:06 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
KBW440 DUSTER Offline
enthusiast

Registered: 12/30/04
Posts: 344
Loc: norman oklahoma
I have a 1966 440 block. Text me at 405-830-8593 for pictures and info. Norman Ok. $500.00 or obo


Edited by KBW440 DUSTER (10/11/18 11:08 AM)

Top
#2562431 - 10/11/18 11:34 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
Triggerfish Offline
top fuel

Registered: 07/25/05
Posts: 1911
Loc: Blairsden, CA
SOLD.. thanks Moparts! New Brawler carb 750 Street Series, mechanical secondaries, electric choke. Was on Summit's display engines, never fired or gas run thru. Just bought from Summits demo sale, but I'm going with an Eddy 750 my brother gave me instead. The Brawler's retail price is right around $400, so $200 plus shipping is what I'm asking & that's a great price.


Attachments
brawler in box.jpg

Brawler 750 bottom.jpg

Brawler 750 MS2.jpg

brawler box.jpg




Edited by Triggerfish (10/12/18 10:27 AM)

Top
#2563486 - 10/13/18 04:07 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
AndyF Online   content
Too Many Posts

Registered: 01/20/03
Posts: 25180
Loc: Oregon
SOLD - 120 amp Denso conversion kit complete with reconditioned Denso alternator new in the box. The bracket kit is used but is complete. Fits B or RB engine. $100 for complete kit with alternator plus shipping. Alternator is heavy so shipping will be $25 or $30 depending on location. PayPal preferred. PM me on the board.


Attachments
DSC_2996 (Large).JPG

AR125 (Large).jpg




Edited by AndyF (10/14/18 11:45 AM)

Top
#2563695 - 10/13/18 11:17 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: AndyF]
'72CudaRacer Offline
top fuel

Registered: 08/31/09
Posts: 1738
Loc: Mooresburg, Tn
Spare rocker arms *NOT A COMPLETE SET*

Mopar Performance, big block, 1.5 ratio, standard offset. $130 for all, shipped (lower 48 only). PM me on here.

NEW- 1 left & 1 right
USED- 3 left & 6 right


Attachments
IMG_0806.JPG

IMG_0809.JPG

IMG_0807.JPG




Edited by '72CudaRacer (10/13/18 11:19 PM)

Top
#2563702 - 10/13/18 11:27 PM Push rods [Re: '72CudaRacer]
'72CudaRacer Offline
top fuel

Registered: 08/31/09
Posts: 1738
Loc: Mooresburg, Tn
USED-Push rods, 3/8" diameter, .083 wall, 5/16" cup, 3/8" ball, effective length 9.350". No damage, changed combo, too long. $150 shipped (lower 48 only) PM ne on here.


Attachments
IMG_0812.JPG

IMG_0813.JPG

IMG_0814.JPG




Edited by '72CudaRacer (10/13/18 11:41 PM)

Top
#2563706 - 10/13/18 11:33 PM Big block valve covers [Re: '72CudaRacer]
'72CudaRacer Offline
top fuel

Registered: 08/31/09
Posts: 1738
Loc: Mooresburg, Tn
Fabricated alum valve covers w/ bolts & one breather (kit), new in box. Mopar Performance #P5155526. $275 shipped (lower 48 only) PM me on here.


Attachments
IMG_0818.JPG



Top
#2563900 - 10/14/18 01:34 PM Water Pump Pullies Including One for 426 Wedge! [Re: '72CudaRacer]
moparjohn Online   content
pro stock

Registered: 03/23/03
Posts: 1238
Loc: N.W. INDIANA
Recently I finished bead blasting and priming my extra water pump pullies. I have now started to look up the ones with part numbers. I have found just one stamped 1821452 and it is for 383 and 426 wedge engines. It is 6 7/8" in diameter and 2 11/16" deep. The price is $40.00 plus shipping. If you interested contact me at: moparjohn@frontier.com
with your zip. If you are looking for an original water pump pulley contact me with the outer diameter and how deep you need as I have many to choose from!
Thanks!


Attachments
OCT 4966.JPG



Top
#2563963 - 10/14/18 03:31 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
mike337 Offline
pro stock

Registered: 04/17/03
Posts: 1295
Loc: Cannelton, IN
Edelbrock Performer 750 CFM Carb. 1407/0392 stamping. Just removed from a running engine, $150

Thanx for the ad Moparts!

moparzone4@aol.com


Attachments
Carb 1.jpg

Carb 2.jpg

Carb 3.jpg

Carb 4.jpg




Edited by mike337 (10/14/18 06:43 PM)

Top
#2564367 - 10/15/18 10:59 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
LemonTwiist Offline
super stock

Registered: 04/04/04
Posts: 767
Loc: Mechanicsburg, PA
FOR SALE: Used metering block #6512 #4780. It still has the power valve, jets, and needle adjusting screws. The part numbers have been sanded off, but can still be seen in the casting. PRICE $35.00 Plus $6.00 postage


Attachments
100_3742.jpg

100_3743.jpg




Edited by LemonTwiist (10/15/18 11:03 AM)

Top
#2564374 - 10/15/18 11:17 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
LemonTwiist Offline
super stock

Registered: 04/04/04
Posts: 767
Loc: Mechanicsburg, PA
SOLD Used Big block 906 head dated April 22, 1970. It is ground 0.10 under. One exhaust manifold stud is broken off It has been cleaned, magna fluxed and has ne cracks. Price $35.00 Plus Postage


Attachments
100_3571.jpg

100_3572.jpg




Edited by LemonTwiist (11/21/18 08:24 AM)

Top
#2564459 - 10/15/18 02:07 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: LemonTwiist]
Joesixpack Offline
I Live Here

Registered: 01/21/03
Posts: 10956
Loc: APACHE JUNCTION AZ
nors Made in the USA hd copper insert dual point distributor cap&made in the USA rotor. will fit all 361-383-413-426w-426h-440+6 cast iron dual points&DC/MP mechanical advance dual point&electronic distributors.
featuring carbon brush, tall coil wire tower,ribbed inside for strength and rigidity. $35 for the pair.
cowgerwilliam035@gmail.com


Attachments
al43 001.JPG

al43 002.JPG

al43 003.JPG

al43 005.JPG



Top
#2564504 - 10/15/18 03:31 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
mjtx Offline
member

Registered: 06/25/12
Posts: 18
Loc: texas
BIG BLOCK MOPAR ENGINE PARTS. 1-set 6-Pac Rods 2951908 ARP polished and shot peened $275.00. 5-6-Pac Rods $20.00 each. 1 set stock 440 LY Rods 1851535 $80.00. 1 440 LY Rod $15.00. 1-Set 440 Rods #1851535 ARP Full floating pins $200.00. 3 Sets of 400 Rods stock $65.00 for each set. 440 Main caps set of 5 $50.00 or $15.00 each. Set 400 stock push rods $20.00.Set 440 stock push rods $25.00. Good used stock rocker arms $65.00 a set. Have a lot of other small big block engine parts. Can ship USPS for about $14.00 for 70 lbs. Pay Pal or USPS money order. Ship within 2 days.Call Mike at 210-415-8925 or email at mjcx@sbcglobal.net with questions.

Top
#2564666 - 10/15/18 10:03 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
CoDart Offline
enthusiast

Registered: 10/06/11
Posts: 298
Loc: Fort Collins, Colorado
All ads require a price.


Edited by tboomer (10/16/18 06:19 AM)
Edit Reason: no price

Top
#2565351 - 10/17/18 11:55 AM 440 roller rockers-sold. [Re: chrisnben]
migsBIG Offline
I Live Here

Registered: 01/20/03
Posts: 17059
Loc: San Jose,CA
Sold.Nearly new Comp Cams Big Block 1.5 ratio Roller Rocker Assemblies. Will work on iron and most aluminum production style heads. Missing box, but near perfect condition as were swapped early on when heads were swapped for more performance. cost $670, $450 shipped 48 states.
pm here for reply.

Sold


Attachments
IMG_94895.jpg

IMG_9491.JPG

IMG_9490.JPG

IMG_94877.jpg




Edited by migsBIG (11/01/18 04:59 PM)
_________________________

Top
#2565525 - 10/17/18 05:18 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
camastomcat Offline
top fuel

Registered: 04/12/05
Posts: 2054
Loc: Salt Lake City
07 vintage World Aluminum Block 4.510 bore, 55mm cam tunnel, all ARP hardware, pushrod restricted oiling .937 lifter bores, small window but professionally repaired. All this block has had B1, B1/MC, and Predator heads and handles more than 1100 HP. $5800
Winberg 4.625 stroke center counterweight, double keyway crankshaft balanced for 7.100 Oliver Billet steel rods, just back from Mile High Crankshaft $1300 2.200
ATI Balancer for crankshaft $300
Scat 1997 vintage 4340 Crankshaft needs light repair with aluminum Rods $750
Fully Ported Predator Heads with all rocker arms, 7/16 double taper pushrods, titanium valves, PSI springs, billet fab valve covers, cast custom intake with modifications ready to go $8000
Billet Fab Oil Pan with balls and heater provision $450
DaVinci 1050 dominator $750
Jessel Belt Drive $1000
55GPH Meziere Water Pump $400
Crower bushing offset lifers $900
Offset distributor $400
Custom 55 mm billet roller camshaft for above application $650
Or all of the above plus pare push rods, rockers, gaskets, and all information it takes to build one of these engines, all you would need is rods, pistons and assembly $16,000. This combo made north of 1100 HP and 830 FP. The parts mentioned here come to over $21,000.
I am selling either this combo or complete 604 Predator with cast intake and single carburetor, billet fab valve covers, 55mm cam, Steel World Hemi block combo, bigger 2.450, 1.860, titanium valves, center counterweight billet Winberg crankshaft, Oliver Steel rods, Titan oil pump with above oil pan, Jessel belt drive, custom pistons, and some spares for $18,500 1050 Davinci carb to pan.
I am only selling one of these to complete my latest project. I will keep the one that doesn't sell.
Call Tom 801 949 7791


Attachments
20160718_153729 (1).jpg

20151121_170504 (1).jpg

Predator3.jpg

Timeslip 4.jpg



Top
#2565826 - 10/18/18 09:15 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
68DART360 Offline
mopar

Registered: 08/31/03
Posts: 489
Loc: Easton, PA
400 2 barrel pulled from a late 70's van with 80K miles on it. complete intake to pan. Virgin never taken apart $400

400 short block with steel crank from a 383 also comes with 915 heads$200 for shortblock and additional $200 for the heads. will separate

66 383 4 barrel motor $500

69 383 complete engine pulled from a 69 coronet $600

383 re ringed new bearings stock 906 heads. Torker intake and MP .509 hydraulic cam. Ran 12.70's in a cuda with 4.10 gears. $1,000

Also have the 727 that above engine ran with. It has been rebuilt many years ago and includes a fairbanks 10" converter stalled around 3500. $350

Would sell engine and trans together for $1,250

PM me here for all questions. Motors are located in Stewartsville, NJ

Thanks, Jim

Top
#2565833 - 10/18/18 09:25 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
CHALLENGER_KEN Offline
mopar

Registered: 01/20/03
Posts: 680
Loc: danville, IN USA
I have the following engine related parts for sale if you need pictures texted please call me and i will do that Thanks

1969 426 Hemi 4 speed distributor part# 2875140 $1000.00 0.B.0.

1970 426 Hemi 4 Speed distributor part# 2875987 $1100.00 O.B.O.

1971 440-6 4 speed Restored carbs complete set $1750.00

1970 Dual Snorkle Restored 383-440 Air Cleaner $375.00

The following are a list of air cleaners that are original and not restored, if you would like them restored I can do that at a additonal cost

1967 B-body 383-440 Correct one not the c body one $250.00 sold thanks moparts

1968-69 340-383-440 round air cleaners $150.00 O.B.O.

1970 383-440 Dual Snorkle $225.00 O.B.O.

1971 383-44O Dual Snorkle $225.00 O.B.O.

1969-71 Oval Air cleaners both Round and Oval lids $500.00 EACH

N.O.S. NOT THE REPO Fram Oval air filters $500.00 O.B.O.

1970 Cast Iron 440-6 Intake $600.00 O.B.O.

1968-69 383-440 Exhaust manifolds with heat riser $400.00
O.B.O.

1970-71 383-440 Exhaust manifolds with heat riser E/C $500.00

If you have questions or offers please call Ken at
1-317-709-3625 or e-mail challengerken@yahoo.com Thanks


Edited by CHALLENGER_KEN (10/19/18 09:15 AM)

Top
#2565970 - 10/18/18 01:10 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: CHALLENGER_KEN]
Joesixpack Offline
I Live Here

Registered: 01/21/03
Posts: 10956
Loc: APACHE JUNCTION AZ
USA MADE NORS SINGLE POINT TUNE UP KIT 361-383-413-440
BRASS INSERT,RIBBED,HD ECHLIN CAP
HD RIVETED MOTORCRAFT ROTOR
PRESTOLITE&MALLORY HD SINGLE POINTS(2)
BLUE STREAK STRAP CONDENSER
$45 MAILED
cowgerwilliam035@gmail.com

Top
#2566599 - 10/19/18 04:47 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: luckydave]
chrisnben Offline
super stock

Registered: 11/16/03
Posts: 991
Loc: Madison, Wisconsin
Brand new FiTech EFI in the box. This is the Meanstreet version that controls fuel only & supports 300-800 HP with 8 injectors, not 4. You still set the timing as usual. Not for boosted engines, only N/A. Click on my link to read about it. Save $150 over retail; buy this one for $849 shipped to you!
Message me here, thanks. FITECH LINK HERE





Edited by chrisnben (10/19/18 04:54 PM)
_________________________
'70 Cuda "Badfish 2"- in the works

Home of MoPar University- We school 'em one at a time!!

Top
#2566600 - 10/19/18 04:53 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: chrisnben]
chrisnben Offline
super stock

Registered: 11/16/03
Posts: 991
Loc: Madison, Wisconsin
Brand new Air/ Fuel gauge, wideband Innovate Motorsports 3844. Comes with both black and white face dials, 8' cord, O2 bung and sensor, etc.
These retail for $200; buy this one for $150 shipped to you.

_________________________
'70 Cuda "Badfish 2"- in the works

Home of MoPar University- We school 'em one at a time!!

Top
#2566668 - 10/19/18 07:40 PM Big Block Fuel Pumps [Re: moparts]
Blues_Cuda Offline
master

Registered: 08/21/03
Posts: 3822
Loc: St. Louis, MO
Big Block Fuel Pumps

NOS in box - $60

Carter High Volume. Used, but said to be very little use - SOLD

Parts store special, New - $25

Buy them all for $100.

All prices include shipping.

314 - 221 -7304 Text, or leave a message

Parts are located in St. Louis, MO.

Scott



Attachments
20181012_192707-1.jpg

20181012_193003.jpg




Edited by Blues_Cuda (10/25/18 10:13 PM)
Edit Reason: Sold Carter pump

Top
#2566702 - 10/19/18 08:42 PM Re: For Sale - Edelbrock 440 Intakes [Re: moparts]
moparmarks Offline


Registered: 11/09/03
Posts: 11079
Loc: Western Colorado High Desert
Both are for RB motors 413, 426w, 440
Performer. Good condition. Good threads. No damage. Looks like someone took a wire wheel to it.
130.00 SOLD
Torker II Really good condition. No damage. Good threads.
155.00 SOLD
Plus shipping
Take check, MO or PayPal
Free delivery to the Fall Fling in LA with prepaid.
Torker is sold
Performer is also sold


Attachments
20181019_152059.jpg

20181019_152113.jpg

20181019_152118.jpg

20181019_152147.jpg




Edited by moparmarks (10/20/18 03:33 PM)
_________________________
71 RR A/G 4-sp Dana, 72 SSP 440, 72 Dart 5.9 4-spd, 97 DAKOTA, amoung others.
Moparmarks Parts & Restorations
Desert Mopar Metal
Grand Jct. CO
970-261-7039
http://moparmark.com/
motormangj@gmail.com

Top
#2567034 - 10/20/18 05:57 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
MoPar Offline
super stock

Registered: 01/23/03
Posts: 1037
Edelbrock Torker 383, good condition $100.00 plus shipping. 608-739-4489


Attachments
20181020_160916.jpg

20181020_160909.jpg



Top
#2567054 - 10/20/18 06:40 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
MoPar Offline
super stock

Registered: 01/23/03
Posts: 1037
Carter AFB carb 4130s 66 383 and 440 manual trans. $150.00 plus shipping. 608-739-4489


Attachments
20181020_104718.jpg

20181020_104734.jpg

20181020_104727.jpg



Top
#2568054 - 10/22/18 08:23 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
Frankie P Offline
member

Registered: 08/25/07
Posts: 11
Loc: Thomaston, CT
Unused fresh restored by Harms Carter avs J74401S. My mistake could be your gain I sent the wrong carb to them the first time. This is a 68 auto carb.Scott will honor his warranty since it has not been installed yet.I
Text 203 509 3900. Email for pics fport01@snet.net
$500.00 plus the ride

Top
#2568320 - 10/23/18 11:15 AM 1971 440 HP block [Re: moparts]
BLACKHEMIRR Offline
mopar

Registered: 09/16/04
Posts: 420
71 440 HP block. Cast 1/24/70. Block is .030 over, but has a little rust staining in a couple cylinders from sitting (since early 80's). Would clean up perfectly @ .040. Has not been magged, but had good anti-freeze in it. I do not believe there are any issues with it. Asking $500. Located in SE PA. Pick-up only for now.

Top
#2568474 - 10/23/18 03:43 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
AndyF Online   content
Too Many Posts

Registered: 01/20/03
Posts: 25180
Loc: Oregon
SOLD - New timing chain for BB engine. Edelbrock single bolt style chain. $70 at Summit I'll sell this one for $40 plus shipping. PayPal preferred, PM me on the board.


Attachments
DSC_3027 (Large).JPG




Edited by AndyF (10/26/18 03:12 PM)

Top
#2568813 - 10/24/18 10:32 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
csmopar Offline
member

Registered: 07/30/06
Posts: 181
Loc: usa
for sale.
a set of date coded 1967 906 bare heads. VERY nice shape, no cracks/damage/milling/porting etc. Was going to use them on a project but went with aluminum heads instead. asking 500 obo plus shipping. Will entertain reasonable offers.

pm for pics


Edited by csmopar (10/24/18 10:32 AM)

Top
#2569318 - 10/25/18 10:23 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: KBW440 DUSTER]
kev440 Offline
member

Registered: 12/04/12
Posts: 38
Loc: Oklahoma
Originally Posted By KBW440 DUSTER
I have a 1966 440 block. Text me at 405-830-8593 for pictures and info. Norman Ok. $500.00 or obo
SOLD SOLD SOLD SOLD SOLD SOLD SOLD SOLD SOLD

Top
#2569552 - 10/25/18 08:47 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
HemiA12Bee Offline
super stock

Registered: 09/26/06
Posts: 923
Loc: Home of the Bluegrass
For sale
True A12 440-6 intake with 80’s Holley six pack carbs and linkage. PM questions here.
$2000
TIA


Edited by 70HemiShaker (10/25/18 08:48 PM)
_________________________
"It takes a Mopar to catch a Mopar”
#469 in A12 Registry....69 1/2 A12 Bee: 4speed, V2 Hemi Orange.
Gonna be a 1 of 1 A12 Hemi Bee with a Passon 5 speed...


Top
#2569836 - 10/26/18 03:15 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
AndyF Online   content
Too Many Posts

Registered: 01/20/03
Posts: 25180
Loc: Oregon
SOLD - Cast aluminum marine pan for big block. Has the original swinging pickup. $75 plus shipping. Shipping will cost some money since this pan is heavy. PayPal preferred. PM me on the board.


Attachments
DSC_0646 (Large).JPG

DSC_0647 (Large).JPG




Edited by AndyF (11/24/18 12:34 PM)

Top
#2570049 - 10/26/18 11:02 PM 71 Complete 440 [Re: moparts]
markz528 Offline
master

Registered: 01/20/03
Posts: 3484
Loc: Milford, OH
Long block 1971 440. See pics for what is included. I do not have the intake or carb. The power steering pulley is bent so it is no good (pump is probably damaged too). This was an AC equipped engine.

The motor was taken out of a running car when I bought it. It is from a C body. That's all I know about it. I am running out of room in my shop and therefore I need to clean out some of my inventory.

$750 - please PM me on this board



Attachments
IMG_5165.JPG

IMG_5166.JPG

IMG_5167.JPG

IMG_5169.JPG




Edited by markz528 (10/28/18 12:03 PM)
_________________________
67 Coronet 500 9.610 @ 139.20 mph
67 Coronet 500 (street car) 13.300 @ 101.75 mph
69 GTX (clone) - build in progress......

Top
#2571230 - 10/29/18 06:47 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: camastomcat]
BB70DUSTER Offline


Registered: 02/03/03
Posts: 4414
Loc: SO CAL
New, TTI Part #44025 Ceramic coated shorty headers, these fit A, B, and E body big blocks, never used, here's a link to TTI's page with all the info...

http://www.ttiexhaust.com/MoparClassics-Headers/44025-Shorty/TTi44025.htm

Retail for $670, plus shipping, Ill take $400 shipped in the US for mine... PM or text for pictures (951)537-8 8 3 0
_________________________

Top
#2571325 - 10/29/18 09:00 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
++MAX WEDGE++ Offline
member

Registered: 04/21/08
Posts: 109
Loc: Near Columbus, Ohio


up
#346 Big block heads. Had these done up and never used them. very light porting on intake and exhaust ports, new guides, valves etc.

550.00 + shipping PM me here, thanks

up


Attachments
heads 6.jpg

heads 1.jpg

heads 2.jpg




Edited by ++MAX WEDGE++ (10/29/18 09:04 PM)

Top
#2572062 - 10/31/18 10:14 AM B-Engine 3.900" stroker crankshaft -- never used - AMERICAN [Re: BB70DUSTER]
YYZ Offline
master

Registered: 01/20/03
Posts: 7233
Loc: Toronto (YYZ) Ontario
Mopar Performance stroker crank for all B-engines (350/361/383/400)

American made, American steel, 8-bolt Hemi flange.

Offset ground to a 3.900" stroke with 2.200" rod journals. Main journals are standard B-engine sized.

Crank has also been fully indexed for perfect TDC, all work performed by a local specialty shop that does many cranks for FHO among others.

This will give 450+ CI in a 383 block and 470+ CI in a 400 block depending on your overbore, but will still rev like a 383 should.

Have gone a different direction -- crank is $825 USD including ground shipping within the lower 48 or Canada.

inviolet@outlook.com or PM me on the board.

Thanks!

Top
#2572742 - 11/01/18 06:21 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
Lcoleman Offline
member

Registered: 11/01/18
Posts: 1
Loc: St Louis, Missouri
NEW 440 CRANKSHAFT STILL IN ORIGINAL BOX.

P/N 3512036

$300.00 OR BEST OFFER. BUYER PAYS SHIPPING.

TEXT 636-856-6211 LARRY

PICTURES BY REQUEST.


Attachments
IMG_0019.jpg




Edited by Lcoleman (11/01/18 06:36 PM)

Top
#2572817 - 11/01/18 09:25 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
SC304 Offline
enthusiast

Registered: 11/18/04
Posts: 267
Loc: Michigan
Engines / Parts For Sale

540 Cubic Inch Wedge Dry Sump Motor

Mega block
Manley Rods
JE Pistons 13-1
Indy 440-1 Heads
Jesel Rockers
.800 Roller
Indy valve covers w/spray bars
Indy Intake W / Holley Dominator
MSD Billet Distributor
Dry Sump pan and Pump, Needs a tank and hoses
2 Starters
2 Water pumps (Mechanical)
Dual ignition system with coils
This motor has Very Little Run time, Project was shelved for a Much larger combination.
Asking 14,000 No Trades Delivery not included


440 HP stock short Block, Casting date is hard to read. Vin and top pad are evident for reference. Very little ridge on a stock bore.
$ 500 no Trades Delivery not included

Pair of 906 heads not hurt but typical dirty
$ 40 bucks Delivery Not included


MSD Digital 7 ignition New in box
$ 800 Delivered within the 48 states

mikewgnr68@gmail.com

Top
#2573967 - 11/04/18 02:14 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: SC304]
moparjohn Online   content
pro stock

Registered: 03/23/03
Posts: 1238
Loc: N.W. INDIANA
I have a full set of 8 440 Mopar connecting rods part number 1851535 and standard bore flat top pistons. These were removed from a 1968 - 1969 motor and stored. The pistons and rods are loose. The price is $125.00 plus shipping. If your interested contact me at: moparjohn@frontier.com with your zip.
Thanks!


Attachments
IMG_4876.JPG

IMG_4877.JPG



Top
#2574355 - 11/05/18 10:04 AM Edelbrock TM7 intake manifold 440 [Re: moparts]
johnnyd Offline
member

Registered: 12/14/11
Posts: 112
Loc: Boston, MA
Selling a nice aluminum Edelbrock TM7 intake manifold for a 440. There are no obvious cracks nor stripped threads and the ports have not been cut on. This will fit 413, 426 wedge and 440 engines, will NOT fit a 383. Cast number is 2715. This intake was one of the best single plane intakes made. These are time proven intakes and made great horsepower. $200

More pics here:
https://boston.craigslist.org/sob/pts/d/edelbrock-tm7-intake-manifold/6741152760.html


Attachments
TM7_small.jpg



Top
#2574454 - 11/05/18 12:51 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: CoDart]
MikeyT Offline


Registered: 07/05/04
Posts: 4628
Loc: Watertown, WI
Hi All,

I am selling my never used 800 Edelbrock AVS Thunderseries carburetor. This is the 1812 model without a choke and retails for $440 dollars at Jegs. I am selling mine for $300 plus shipping from 53094.

The 800 is a fun carb especially for a hot 383 or moderately built 440. I find them fun and easy to tune with a kit. Please Private message me here.

Thank you moparts for the add.
Mike
_________________________
Currently mopar less for the first time in a very long time.

Top
#2574750 - 11/06/18 07:56 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
DusterKid Offline
super stock

Registered: 01/02/05
Posts: 919
Loc: Keymar, MD
440 source BB passenger side outlet water pump housing/pump. Bought this 3 years ago when I switched from a SB to a BB. Used it for 2 race seasons and than switched back to a SB. No longer need it. Asking:

Housing - $75
Housing with pump - $100
(Accessories not included, bolts to attach to block, top water neck, gauge fitting)

Price is shipped to anywhere in the lower 48. Will ship elsewhere, but may have to charge more depending on shipping cost.


Attachments
waterpump.JPG



Top
#2575473 - 11/07/18 03:56 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
dsd70bee Offline
I Live Here

Registered: 08/24/03
Posts: 14195
Loc: oak park, il.
Weiand tunnel ram type 440 SIX PACK intake manifold, excellent used condition $1350.00 (708)288-2879 Scott


Attachments
parts 9-1-16 014.JPG

parts 9-1-16 015.JPG

parts 9-1-16 016.JPG



Top
#2575492 - 11/07/18 04:18 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
dsd70bee Offline
I Live Here

Registered: 08/24/03
Posts: 14195
Loc: oak park, il.
1969 440 Block and main caps, over the counter block with no VIN stamped into it $2500.00 (708)288-2879 Scott


Attachments
part 10-23-2015 003.JPG

part 10-23-2015 004.JPG

part 10-23-2015 009.JPG

part 10-23-2015 010.JPG



Top
#2575837 - 11/08/18 10:10 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
bn_race Offline
member

Registered: 11/08/18
Posts: 2
Loc: Ohio
440 Block .030" over. Honed ready to assemble
New Wiseco Dome Pistons/Pins from Indy Cylinder Head for stock & Indy SR/440-1 heads ($750)
New Eagle Rods 6.76"
New Eagle 3.75" Crank Factory 10/10

$1,999


RacingJunk


Edited by bn_race (11/08/18 10:56 AM)

Top
#2576343 - 11/09/18 11:14 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: bn_race]
Joesixpack Offline
I Live Here

Registered: 01/21/03
Posts: 10956
Loc: APACHE JUNCTION AZ
MADE IN THE USA HD TUNE UP KIT

USA MADE NORS ,HD,CARBON BRUSH EQUIPPED,RIBBED,TALL COIL WIRE TOWER POWEREADY DISTRIBUTOR CAP
HD RIVETED POWEREADY ROTOR
DELCO REMY DUAL POINTS SET
VULCAN WIRE TYPE CONDENSER
FITS 1958-1959-1960-1961-1962-1963-1964-1965-1966-1967-1968-1969 DODGE,PLYMOUTH,CHRYSLER 361-383-413-426W-426H-440+6 CAST IRON FRONT MOUNTED DUAL POINT DISTRIBUTORS
$45
cowgerwilliam035@gmail.com


Attachments
3311 002.JPG

3311 001.JPG



Top
#2576490 - 11/09/18 03:40 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: Joesixpack]
Powerflow Online   content
super stock

Registered: 07/31/06
Posts: 790
Loc: New Jersey
1970-71 4962S BBD Carburetor for 383 engine. Sitting on my shelf for over 30 years. Looks complete except for choke pull-off link. Should be cleaned or rebuilt after all this time. $35.00 + shipping. Send zip code and I'll figure out what shipping will be. Best contact is via Moparts PM.


Thanks for looking!
Harold


Attachments
4962S 2.JPG

4962S 1.JPG

4962S 3.JPG



Top
#2576765 - 11/10/18 10:53 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: Powerflow]
moparjohn Online   content
pro stock

Registered: 03/23/03
Posts: 1238
Loc: N.W. INDIANA
In the first picture are
1970 through 1974 valve cover breather caps bead blasted and primed.
The factory part number for these is 3462094. The price is $20.00 each.
I also have 2 original hoses for these both have the molded lines.
The one on the left is $10.00 and the one on the right with clamps is SOLD.
In the second picture is a Mopar Performance valve cover accessory kit part number P4120272 for $20.00.
In the third picture is 5 different oil filler caps $10.00 each.
In the last picture are 2 NOS Mopar PCV grommets 3751510 for $20.00 each.
Prices do not include shipping.
Contact me at: moparjohn@frontier.com with your zip if interested.
Thanks!


Attachments
NOV 5097.JPG

NOV 5126.JPG

NOV 5128.JPG

NOV 5127.JPG




Edited by moparjohn (11/15/18 06:20 PM)

Top
#2576857 - 11/10/18 04:46 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
hemi-itis Offline
I Live Here

Registered: 12/29/07
Posts: 11188
Loc: Great Neck,LI,new york
Feb 1969 virgin 2nd gen iron HEMI heads.Came off my engine for aluminum fueler heads. 173cc chambers,never damaged or even port matched!

Asking $3000,,,,located on Long Island.Shipping weight is 110 lbs.

I also have a collection of push rods,valves & springs and retainers for a good price if needed.

Please PM me here


Attachments
7.9.18 021.jpg

7.9.18 020.jpg

7.9.18 024.jpg


_________________________
HEMI-ITIS has no cure. My condition is fully BLOWN!!!

New best 60ft,, 1.42,1/8, 6.0 @117,, 9.38 @146.75 with 6 lbs boost @3700 lbs

Top
#2576859 - 11/10/18 04:49 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
hemi-itis Offline
I Live Here

Registered: 12/29/07
Posts: 11188
Loc: Great Neck,LI,new york
New in the box 4.5 bore Diamond pistons with pins,locks & rings. price these these new then scoop these up for $1000

PM me here


Attachments
7.9.18 037.jpg

7.9.18 031.jpg

7.9.18 036.jpg

7.9.18 039.jpg




Edited by hemi-itis (11/10/18 04:57 PM)
_________________________
HEMI-ITIS has no cure. My condition is fully BLOWN!!!

New best 60ft,, 1.42,1/8, 6.0 @117,, 9.38 @146.75 with 6 lbs boost @3700 lbs

Top
#2577545 - 11/12/18 02:10 PM 383-400 Edelbrock 6 Pack Intake [Re: moparts]
blewbyu Offline
master

Registered: 01/22/03
Posts: 3649
Loc: Florida
This is very good intake for 383 or 400 $375.00 plus shipping.

blewbyu2bad@aol.com


Attachments
383 6 pack.JPG



Top
#2577554 - 11/12/18 02:43 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
ChrgrCuda Offline
super stock

Registered: 08/24/08
Posts: 793
Loc: Texas, USA
Indy 2D Intake manifold. Ports are untouched. Powder coated. $250.00.


Attachments
Intake 1.jpg

Intake 4.jpg

Intake 5.jpg




Edited by ChrgrCuda (11/12/18 02:45 PM)
_________________________
68 Cuda Notchback [Email]10.86@120[/Email] 69 Charger R/T 440/505 2009 Challenger SRT8

Top
#2577591 - 11/12/18 05:03 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
dynamite Offline
pro stock

Registered: 01/02/07
Posts: 1405
Loc: NEW JERSEY
Nice 440 block,stock bore, no or little rust,very little ridge, could probably use stock size pistons.Has main caps.Clean block $550.00..believe 1969 block.. In Jersey PM me Larry

Top
#2577655 - 11/12/18 07:30 PM RB STR 14 6 pack and 4 Barrel Intake [Re: dynamite]
blewbyu Offline
master

Registered: 01/22/03
Posts: 3649
Loc: Florida
I have an unmodified STR 14 Intake with a 6 pack top and a 4 Barrel Dominator top. $1500.00 plus shipping from Florida

blewbyu2bad@aol.com


Attachments
str.JPG

str 1.JPG



Top
#2577658 - 11/12/18 07:33 PM AA Repro Max wedge Crossram to fit 440 Headsl Intake [Re: blewbyu]
blewbyu Offline
master

Registered: 01/22/03
Posts: 3649
Loc: Florida
This is an AA reproduction crossram for 440 engines with 440 heads. Comes with carb linkage. Also include are 2 new Air cleaners assy. Just ad carbs $2500.00 plus shipping


blewbyu2bad@aol.com


Attachments
crossram.JPG

crossram 1.JPG




Edited by blewbyu (11/12/18 07:36 PM)

Top
#2577874 - 11/13/18 09:38 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: dynamite]
an8sec70cuda Offline
I Live Here

Registered: 01/19/03
Posts: 11020
Loc: Marion, South Carolina [><]
G440 HP 1971 engine completely rebuilt, fresh, never fired, done right.
Cast 12/16/70, built 1/11, VIN 1A150062

I built this engine to be close to factory correct for a restoration, but still run really strong like they ought to b/c I've seen too many rebuilt 440s that run like dogs.

Quick rundown of the build...
fresh 4.375" bore w/ Wiseco forged flattop pistons, true 10.1:1 compression
forged crank turned .010"/.010", ARP rod bolts, balanced rotating assembly (internal)
correct hemi/six pack oil pan, 1/2" pickup
Summit K6401 cam .466"/.488" lift, 224°/234° at .050" (slightly bigger than stock, works great w/ either factory manifolds or headers and stock torque converter), double roller timing chain
1971 date correct 346 casting heads completely rebuilt w/ new valves, Comp Cams valve springs, retainers, and locks, hardened exhaust seats, good valve job and mild bowl porting
correct 1971 valve covers and 3512501 intake manifold

Complete build sheet w/ part numbers, clearances, and all specs will be provided.

$4,900 or best reasonable offer. Will wrap in plastic, strap to a pallet, and drop off at terminal for shipping that YOU pay for and arrange. For sale locally also...willing to meet/deliver a reasonable distance.
PM me here or call/text 843-431-8376 if serious.
Thanks!


Attachments
440-7.jpg

440-17.jpg




Edited by an8sec70cuda (12/13/18 03:26 PM)
_________________________
CHIP
'70 hemicuda...8.91 at 150.5 mph street car...Mopar Action feature Dec. '14
'69 road runner 440 w/ Indy SRs
'69 road runner 440-6, 4 speed...Dad's ride
'71 Demon 340 resto project
'06 GMC 2500HD LBZ Duramax...toy hauler
'16 Grand Caravan SXT...baby hauler

Top
#2577942 - 11/13/18 12:09 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
AndyF Online   content
Too Many Posts

Registered: 01/20/03
Posts: 25180
Loc: Oregon
Matched set of 906 heads. 8/21/8 casting and 8/23/8 casting. Heads have been hot tanked and magged. All threads are good except for one accessory hole. That head could be repaired or used on the driver side. $200 for the pair plus shipping. PayPal preferred, PM me on the board.


Attachments
DSC_3108 (Large).JPG

DSC_3106 (Large).JPG

DSC_3107 (Large).JPG



Top
#2578986 - 11/15/18 09:28 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
dynamite Offline
pro stock

Registered: 01/02/07
Posts: 1405
Loc: NEW JERSEY
Have a clean 440 block.. stock bore,stock deck,clean bores ,could probably run stock pistons..with main caps.. $ 550.00.. Located in Jersey..call 772-240-4214 cell. or PM. for pics to e-mail only. date code 11-68, call Larry

Top
#2579207 - 11/16/18 01:22 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: dynamite]
Joesixpack Offline
I Live Here

Registered: 01/21/03
Posts: 10956
Loc: APACHE JUNCTION AZ
MADE IN THE USA HD BLACK NORS DUAL POINT DISTRIBUTOR COPPER INSERT CAP&ROTOR

USA MADE NORS ,HD,CARBON BRUSH EQUIPPED,RIBBED,TALL COIL WIRE TOWER BLACK,COPPER INSERT DISTRIBUTOR CAP
HD RIVETED ROTOR

FITS 1962-1963-1964-1965-1966-1967-1968-1969-1970-1971 DODGE,PLYMOUTH,361HP, 383HP-413HP,426W,426H-440+6 CAST IRON DUAL POINT DISTRIBUTORS
$35
cowgerwilliam035@gmail.com


Attachments
AL122 002.JPG

AL122 004.JPG

AL122 006.JPG



Top
#2579208 - 11/16/18 01:26 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: Joesixpack]
Joesixpack Offline
I Live Here

Registered: 01/21/03
Posts: 10956
Loc: APACHE JUNCTION AZ
MADE IN USA IBK-1003 HD BLACK, COPPER INSERT , NOS DUAL POINT DISTRIBUTOR CAP&NOS IBK-1016 ROTOR

IBK-1003 WITH MADE IN U.S.A. ON TOP # INSIDE,HD,CARBON BRUSH EQUIPPED,RIBBED,TALL COIL WIRE TOWER . COPPER INSERT DISTRIBUTOR CAP
HD IBK-1016 RIVETED ROTOR WITH # ON TOP

FITS 1962-1963-1964-1965 DODGE,PLYMOUTH,361HP,383HP-413HP,426SW,413MW,426MW CAST IRON DUAL POINT DISTRIBUTORS$60
cowgerwilliam035@gmail.com


Attachments
IBK1003 002.JPG

IBK1003 003.JPG

IBK1003 004.JPG

IBK1003 010.JPG



Top
#2579211 - 11/16/18 01:30 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: Joesixpack]
Joesixpack Offline
I Live Here

Registered: 01/21/03
Posts: 10956
Loc: APACHE JUNCTION AZ
MADE IN CANADA IBK-1003 HD BLACK NOS DUAL POINT DISTRIBUTOR CAP&NOS IBK-1016 ROTOR

IBK-1003 WITH MADE IN CANADA ON TOP # INSIDE,HD,CARBON BRUSH EQUIPPED,RIBBED,TALL COIL WIRE TOWER . DISTRIBUTOR CAP
HD IBK-1016 RIVETED ROTOR WITH # ON TOP

FITS 1962-1963-1964-1965 DODGE,PLYMOUTH,361HP,383HP-413HP,426SW,413MW,426MW CAST IRON DUAL POINT DISTRIBUTORS$50
cowgerwilliam035@gmail.com


Attachments
CANADA 002.JPG

CANADA 003.JPG

CANADA 004.JPG

CANADA 009.JPG



Top
#2579214 - 11/16/18 01:33 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: Joesixpack]
Joesixpack Offline
I Live Here

Registered: 01/21/03
Posts: 10956
Loc: APACHE JUNCTION AZ
MADE IN THE USA HD TAN NORS DUAL POINT DISTRIBUTOR BRASS INSERT CAP&ROTOR

USA MADE NORS ,HD,CARBON BRUSH EQUIPPED,RIBBED,TALL COIL WIRE TOWER TAN BRASS INSERT DISTRIBUTOR CAP
HD RIVETED ROTOR

FITS 1966-1967-1968-1969-1970-1971 DODGE,PLYMOUTH, 383HP-426H-440+6 CAST IRON DUAL POINT DISTRIBUTORS$55
cowgerwilliam035@gmail.com


Attachments
TANBRASS 002.JPG

TANBRASS 003.JPG




Edited by Joesixpack (11/16/18 01:33 PM)

Top
#2579217 - 11/16/18 01:35 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: Joesixpack]
Joesixpack Offline
I Live Here

Registered: 01/21/03
Posts: 10956
Loc: APACHE JUNCTION AZ
MADE IN THE USA HD TAN NORS DUAL POINT DISTRIBUTOR CAP&ROTOR

USA MADE NORS ,HD,CARBON BRUSH EQUIPPED,RIBBED,TALL COIL WIRE TOWER TAN DISTRIBUTOR CAP
HD RIVETED ROTOR

FITS 1966-1967-1968-1969-1970-1971 DODGE,PLYMOUTH, 383HP-426H-440+6 CAST IRON DUAL POINT DISTRIBUTORS$45
cowgerwilliam035@gmail.com


Attachments
TANCAP 002.JPG

TANCAP 003.JPG

TANCAP 004.JPG




Edited by Joesixpack (11/16/18 01:36 PM)

Top
#2580246 - 11/19/18 01:06 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
MoPar Offline
super stock

Registered: 01/23/03
Posts: 1037
Carter carb #3859 SA for 1965 426 street wedge with 4 speed $150.00 plus delivery. 608-739-4489


Attachments
20181114_174915.jpg

20181114_174820.jpg

20181114_174940.jpg



Top
#2581505 - 11/22/18 10:37 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
willie_68coronet Offline
enthusiast

Registered: 11/21/07
Posts: 218
Loc: fridley, minnesota
Set of 17 Manton stage 3 push rods, 3/8" .095" wall, 9.5" effective length and 9.65 overall length. Ball and cup sizes of 5/16". 6 dyno pulls only. Shipped for $140


Attachments
IMAG0199.jpg


_________________________
Bloodgeon Mobile, 68 coronet 500 with a 383 and a torqueflight. Max wedge Indy EZ-1 headed 446 in the works


Top
#2581630 - 11/22/18 03:27 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
dsd70bee Offline
I Live Here

Registered: 08/24/03
Posts: 14195
Loc: oak park, il.
1 pr 1967 440 HP exhaust manifolds, one year only, very hard to find $550.00 for the pair (708)288-2879 Scott


Attachments
parts 11 21 2018 006.JPG

parts 11 21 2018 004.JPG

parts 11 21 2018 012.JPG

parts 11 21 2018 008.JPG



Top
#2581772 - 11/22/18 10:08 PM 440 Street Strip Engine [Re: moparts]
Newbomb_Turk Offline
member

Registered: 09/19/05
Posts: 166
Loc: Archbald, PA
I have a complete long block 440 engine .030 over for sale. It has pocket ported Edelbrock Aluminum heads, Milled to 79cc chambers, Edelbrock RPM Air Gap intake, Weisco Flat top Pistons, Eagle H-beam 6.76 rods, Total Seal Gapless Top Rings,less than 3% leakdown after approx 200 runs, Brand new Ohio Crankshaft, Std, Std. Mopar Purpleshaft 590 solid cam, Smith Bros pushrods, Crane Roller Rockers, 8 Qt Oil Pan, HV Melling Oil Pump. Motor is 11.6:1 CR w/.019 head gasket, swap to a .040 Head gasket, and you have a street engine. Motor ran 10.60 in a 3300 lb car shifting at 6200. Motor is still in the car but winterized, (done every year). Will not pull out due to a deadbeat buyer, (Typical!) unless receive a deposit. Complete engine is for sale, but no accessories. 727 Transbrake trans & converter is also available for $1400 Please ask away on questions, I tried to cover all the bases! Thanks, John

Price engine $3900

Price trans & converter $1400 (must sell engine first)

Package deal for both just message me for details

newbombturk1@earthlink.net

Sorry for the confusion!

MOTOR AND TRANS ARE SOLD!!!! THANKS MOPARTS!!!!! up


Attachments
Demon motor 1.jpg

Demon motor 2.jpg

Demon motor 4.jpg

Demon motor 6.jpg




Edited by Newbomb_Turk (11/29/18 01:03 PM)
_________________________
1971 Demon 440 auto Drag car full tub, Best 10.47 @ 126

Top
#2581946 - 11/23/18 12:43 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
jbeintherockies Offline
member

Registered: 05/10/11
Posts: 181
Loc: Aurora, CO
6 Eagle connecting rods and 6 Ross racing forged pistons for a 440 RB big block Chrysler for sale

Price: $250.00

Rods:
Eagle rods with matching bushed caps; 6.76" connecting rod length center-to-center; ARP 8740 7/16" rod bolts; 1.094" full floating piston pins; H beam rods

These are the exact same rods found on Summit Racing's website:
https://www.summitracing.com/parts/esp-6760c3d-1/overview/make/chrysler

Pistons:
Ross pistons 437RB 80762 (3 left side, 3 right side); full floating 1.094" piston pins with spiralocks; 4.350" diameter (.030" over bored 440); domed

These are the exact same pistons found on Summit Racing's website:
https://www.summitracing.com/parts/ros-80762/overview/make/chrysler

I will not separate or sell individually. All 6 rod-piston combinations will be sold together.

Yes, I know a 440 needs 8 rods and pistons. The other two are gone and these are all that remain. You can buy the exact same rods ($70) and exact same pistons ($120) individually. There is no damage that I can see on the rods or pistons that I am selling in this listing.

Link to view photos of pistons and rods:
https://drive.google.com/file/d/185_KKXdrx8_oJMGmghItZ1NLiWxFdqwc/view?usp=sharing
https://drive.google.com/file/d/1TPeTU6STUQ5jYeF4ftwA_6WC2kBn51ry/view?usp=sharing
https://drive.google.com/file/d/1jAKglLGHtbC1feicT5_81JjzwZy5g4FJ/view?usp=sharing
https://drive.google.com/file/d/1bp5Zr8ZWKWu7SqU5o2y-OHEGApqkZLKe/view?usp=sharing
https://drive.google.com/file/d/1R3RVfVpAWa-0IvulFaI9t2TvHErK1Jte/view?usp=sharing
https://drive.google.com/file/d/1W8ZfUqw2tTIHCWJAbQdKibOJTX47JnH9/view?usp=sharing
https://drive.google.com/file/d/1AwZtdT2uPxzWqlBPOlNTHYxMiy8ifKcs/view?usp=sharing

Top
#2582813 - 11/25/18 11:09 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
1970RatRoaster Offline
member

Registered: 11/22/18
Posts: 3
Loc: Canada
440 Rods forge number 1851535 been resized with new ARP bolts. Ended up not using them. $160 includes ship. ETrader1@hotmail.com

Top
#2582978 - 11/25/18 05:35 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: 1970RatRoaster]
69 charger man Offline
enthusiast

Registered: 11/10/06
Posts: 383
Loc: NJ
70s big block manifolds. 100$ Or b/o plus shipping. Please pm me. thanks for the add.


Attachments
26484B62-F75A-4657-AA83-FCCB95F17971.jpeg



Top
#2583737 - 11/27/18 01:25 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
Paul Jacobs Offline
super stock

Registered: 03/19/03
Posts: 964
Loc: INDIANA
SOLD


Attachments
heads.JPG




Edited by Paul Jacobs (12/11/18 05:39 PM)

Top
#2585397 - 11/30/18 07:41 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
HemiMark Offline
enthusiast

Registered: 10/13/05
Posts: 254
Loc: Pittsburgh, PA
Str-14 Comes with carbs and linkage 2200.00 plus the ride from Pittsburgh
PM me here


Attachments
IMG_5710.JPG



Top
#2586597 - 12/03/18 11:17 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: HemiMark]
Joesixpack Offline
I Live Here

Registered: 01/21/03
Posts: 10956
Loc: APACHE JUNCTION AZ
Distributor Shaft Bearing:
This is a NOS distributor shaft bearing package & washer package for the aluminum distributor with 8 cylinder engines AND SINGLE point distributors. This is a original NOS Mopar part in it’s original packaging.

Part Number:
2275229 [supercedes P/n 1881947]
$50
cowgerwilliam035@gmail.com


Attachments
2275229 002.JPG

2275229 001.JPG



Top
#2586631 - 12/03/18 12:20 PM New front sump oil pan [Re: moparts]
Mack3636 Offline
member

Registered: 11/29/18
Posts: 7
Loc: Michigan
Brand New Mopar Performace B/RB front sump oil pan. Powder coated HEMI Orange. Fits C bodies with 361-383-413-440-426 & 426 HEMI.

Asking $100. plus shipping

I really want to sell this! Lowering the price to $75.


Attachments
Oil pan 1.jpg




Edited by Mack3636 (12/27/18 02:20 PM)

Top
#2586778 - 12/03/18 06:44 PM For Sale - Big Block Engine - 4th Quarter [Re: Mack3636]
docr Offline
super stock

Registered: 08/24/06
Posts: 764
Loc: Indiana USA

FOR SALE:
Carter 4327S AFB – ’67 440 HP (A134) – “One Year Only” – For Auto Trans.
750 CFM - Coronet/Charger RT or Plymouth GTX
J6 Date (Sept. ’66), with desirable 4327S tag, & vacuum pull off
$385.00 - Includes Shipping and Insurance in lower 48 states
No History, but Good Condition (Nothing stuck)
Will need kit/rebuilt

*******************
Carter 3253S- AM1 AFB '62 361CI (305 Horse Power) A/T – HP Dodge or
Power Pac Ply. ---- (Missing auto spring coil thermostat assembly) --- $60.00
*** Will need rebuild - Shipping extra ****

E-mail only sacdrose@att.net
Thanks Moparts.com

Top
#2587394 - 12/05/18 06:56 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
Dap Offline
top fuel

Registered: 01/20/03
Posts: 1855
Loc: Staten Island N.Y.
I have a Callie’s Magnum XL

Stroke - 4.500
Pins- 2.00 Rod Length 7.00
Bob weight 2350g
SN# 61906
$2400

I bought this from Dan Costello years ago. It is new still in the box.
email Contact me for more photos. Dap8998@earthlink.net

Thanks Moparts


Attachments
766A89D5-3E74-4590-8F0A-F603034ADDDF.jpeg




Edited by Dap (12/05/18 08:30 PM)
_________________________
PRH446
10.084 @ 135.21 mph N/A through chambered mufflers,3300lbs. Stock stroke wedge

Top
#2587856 - 12/05/18 09:53 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: Dap]
BIGJOE30 Offline
super stock

Registered: 09/01/05
Posts: 721
Loc: Pittsburgh area
Sidewinders from Marsh Performance with about a 100 miles on them. These are 84cc heads and have a stage 1 valve job by Larry Smith. Upgraded SI Valves 2.14 1.81
with 10 degree locks and retainers and clip on valve seals no expense spared ! Heads flow 295 CFM @600. Has Comp 924 double valve springs for Hydraulic can 123 seat and 295 open pressure.
Good to about .525 lift. These heads are like new and Made serious power on my 440. I’m going back to manifolds and a more stock approach. Have original padded boxes to ship them in
SOLD


Edited by BIGJOE30 (12/19/18 12:27 AM)

Top
#2587881 - 12/05/18 10:40 PM Mopar 318 340 383 414 440 Carburetors and others [Re: BIGJOE30]
davesmopars Offline
master

Registered: 08/01/04
Posts: 2970
Loc: cheshire, ct
Mopar 318 340 383 414 440 Carburetors and others
3444s 64 413 100.00
3858s J4 65 413 100
4401s have check date 68 auto 125.00
4401s J7 68 383 auto 125.00
4424s M7 68 340 4 speed 175.00
4425 have to check date 68 340 auto 150.00
4426s H7 68 383 4 speed 175.00
4426s have to check the date 68 383 4 speed 175.00
4429s J7 68 440 auto 150.00
4640 have to check the date 69 440 auto 175.00
R4166 69 440 auto 140.00
4933s A0 70 340 4 speed with solenoid 275.00
4933s C0 70 340 4 speed with solenoid 275.00
4934 have to check date 70 340 auto 150
4966 J0 71 440 auto 80.00
4xxx have get the numbers 71 440 auto
4749 383 holley replacement 383 440 75.00
R6160 72 440 75



4722 318 2 Barrel
4608 2barrel
8093 2 barrel
8994 1 barrel
9020 1 barrel
holley 2 barrel no number yet
holley 8958 450 CFM 4 barrel 80.00
holley 7309 2 barrel 50.00

I will take picture on request
all plus shipping

Top
#2588405 - 12/06/18 10:51 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
dsd70bee Offline
I Live Here

Registered: 08/24/03
Posts: 14195
Loc: oak park, il.
I have three Max wedge 3447 carbs, one has a date code of F2, one has a date code of C3 and the third one does not have a date code, I am selling as cores to restore $750.00 each or all three for $2000.00 (708)288-2879 Scott


Attachments
parts 4-15-16 004.JPG

parts 4-15-16 005.JPG

parts 4-15-16 006.JPG

parts 4-15-16 007.JPG



Top
#2589822 - 12/10/18 11:18 AM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
BB70DUSTER Offline


Registered: 02/03/03
Posts: 4414
Loc: SO CAL
MSD 8387 "Ready to Run" Billet Distributor, Fits 440 or Hemi engines, Used, $400 new, $200 for mine, buyer pays shipping from Hemet, CA 92544. PM or text for more info or pics... (951)537- 8 8 3 0
_________________________

Top
#2589994 - 12/10/18 04:43 PM NEW solid roller lifters comp 87019-16 endure X $350 shipped [Re: moparts]
mgoblue9798 Offline
enthusiast

Registered: 03/16/10
Posts: 300
Loc: Atlanta, GA
Brand new, no longer need these
$350 shipped to lower 48.



Attachments
comp roller pic.jpg




Edited by mgoblue9798 (12/16/18 06:51 PM)

Top
#2592833 - 12/16/18 01:23 PM ****SOLD SOLD ****** [Re: moparts]
B1Frank Offline
super stock

Registered: 09/18/07
Posts: 719
Loc: West Virginia
***SOLD SOLD THANKS RICK !!! FREE SHIPPING ****New chrome B/E big block headers,well built don;t know the brand,..i got these from a guy on the west coast about #2 years ago,..he used these for mock-up only,..#1 7/8 tube's,.. thick flanges #3 inch out,..one dent,.. some scratches,,not perfect but for a nice driver,... manifolds,... FREE SHIPPING to the moparts people thanks moparts


Attachments
new chrome  big block headers.jpg

new chrome big block headers photo #2.jpg




Edited by B1Frank (12/30/18 10:57 AM)

Top
#2592893 - 12/16/18 03:56 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: B1Frank]
crescentbar Online   content
member

Registered: 11/15/13
Posts: 23
Loc: wa
1 used set of crane adjustable rockers and shafts,complete with bolts and spacers,with a set of ball and cup push tubes(383/440) in good shape
350 plus shipping
1 used isky 165135 z35 grind camshaft and lifters(lifters marked for position,solid lifters,3000-7000 rpms,.525 lift ,3 bolt,in good shape 250.00 plus shipping
will possible part trade for a good street performance hydraulic camshaft and lifters
thanks Tim 360 908 3961


Edited by crescentbar (12/24/18 12:35 PM)

Top
#2592894 - 12/16/18 04:03 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: crescentbar]
crescentbar Online   content
member

Registered: 11/15/13
Posts: 23
Loc: wa
1 set of 213 cylinder heads complete with valves and springs,in good shape,will need to be freshed up,(1973) famous 1 year only motor home heads with the extra cooling 120.00 plus shipping
1 1972 440 cast crank,3698461,in good shape,standard/standard,I think you can reuse with out polishing, 50.00 plus shipping
thanks Tim 360-908-3961


Edited by crescentbar (12/24/18 12:36 PM)

Top
#2593249 - 12/17/18 02:14 PM 1969 440 HP [Re: moparts]
BLACKHEMIRR Offline
mopar

Registered: 09/16/04
Posts: 420
1969 440 HP engine for sale. 2/18/69 cast, 3/3/69 assembly. Block is .030 over, will need to go .040 to be perfect. Has original heads. For the most part, it's complete except for air cleaner, distributor, exhaust manifolds. Has a 4640 AVS carb. Excellent engine for rebuild. Asking $1,700, will consider offers. Located in SE PA. PM me here if interested. Thanks for the ad.

I also have an original 69 1/2 intake, carbs, and air cleaner lid I might consider selling along with the engine if someone's looking to put a 6 bbl engine together. I would need $3,500 OBRO for everything.

Top
#2594346 - 12/19/18 03:04 PM Re: 1967 440 HP Exhaust Manifold [Re: BLACKHEMIRR]
joewhite440 Offline
pro stock

Registered: 04/15/03
Posts: 1304
Loc: Western Pa
1967 Plymouth GTX 440 HP Exhaust Manifolds

Part number Left 2806974 2 (12 19 6) Manufacture date)
Part number Right 2806900 N1 (? ? ^)

Someone put a heat shield on the left one for Master Cylinder (Bolts On)

Positive off that car because my brother inlaws family bought the car new

$350 plus shipping from 15052
PM here or jw1969rr@yahoo.com


Attachments
DSCN2026.JPG




Edited by joewhite440 (12/28/18 05:47 AM)

Top
#2594670 - 12/20/18 10:38 AM 572ci SOLD [Re: moparts]
RonP Offline
top fuel

Registered: 01/20/03
Posts: 1624
Loc: Jacksonville, NC
SOLD



572ci.
Mega block NOT aluminum
Indy 440-1s
Indy 4403x intake
Holley ultra hp 1250
GRP rods
Camp motion roller cam
OFFset distributor
Crank trigger
Vacuum pump
Belt drive timing
Indy reverse flow cooling
Harland Sharp rockers 1.5 ratio
Indy dual line oiling
I'm sure there's more...

25 passes since refresh.
Been 5.82 1/8 in 3550lb 64 dodge 440

ron4401@yahoo.com


Edited by RonP (12/30/18 09:09 PM)
_________________________


CWO5 U.S. Marine Corps
493,footbrake, full exhaust, drag radials, 3380#
[email]6.02@113.7[/email]

Top
#2595601 - 12/22/18 05:07 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
wish4hemi Offline


Registered: 02/27/15
Posts: 5
Loc: IL
Six Pack Air Filter P4529965. Ships in the original box. Never been on a car. Send PM if interested.
$165 shipped to the lower 48


Attachments
IMG_8940.JPG

IMG_8941.JPG



Top
#2596915 - 12/25/18 05:56 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: wish4hemi]
BryanRad Offline
mopar

Registered: 06/05/04
Posts: 622
Loc: Cottageville, WV
8 – LY Connecting Rods – Bronze Bushed – ARP Bolts – resized when bolts installed $125

P4120661 – 557 purple shaft cam and lifters – bought in 2010 – less than 20 passes $135

7 – KB 236 0.060 pistons for 440 $100

Taylor battery box 9.5” long, 8.25” wide, 8” high w/stainless 3/8 all thread $40

Hooker 5320’s – B&E Body 2 1/8 adjustable race header - $325

440 block 0.030 over – crack between soft plug driver side – no other issues Easy fix with shallow hard block fill or pin end of crack and epoxy it. $250

440 0.060 block. Hardblock tall fill. Needs a fresh hone and would be ready to go. $200

Cast 440 Crankshaft - $75


Complete 383 engine less intake and carb 6 26 64 casting date – virgin to my knowledge - turns over with wrench $225


Contact by pm and will provide phone number.


Edited by BryanRad (12/29/18 04:28 PM)

Top
#2597008 - 12/25/18 11:08 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
tlc Offline
member

Registered: 10/10/10
Posts: 11
Loc: mn
511 Big Block Mopar
Based on 400 block--half filled block
Used in Corvette Roadster (2200 lbs with driver) for past few seasons
Ran 152 mph in super gas trim
Ran 8.50-8.60 at 155 mph in bracket mode
Muscle Motors rotating assembly
Isky roller cam-part no. 165173
Indy SR ported heads
T&D rockers--1.6 ratio
Edelbrock Intake
ATI balancer
Milodon swing oil pickup
MSD billet distributor
Fresh rings and bearings
Mancini Aluminum main caps and stud girdle


Selling intake to pan
$7,500 or best offer
Going a different route and would like to sell quickly

Call or text Tom at 218-341-6731 after 3:00 p.m. central time

https://www.youtube.com/watch?v=02zTd9ClJvE

Vacuum pump and alternator available as well as powerglide adapter plate


Attachments
Resized_2 (2).jpg

Resized95.jpg

Resized_2 (5).jpg

Resized_2 (10).jpg



Top
#2597428 - 12/26/18 11:39 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
Jim_Lusk Offline
I Live Here

Registered: 03/18/03
Posts: 17434
Loc: Fresno, CA
413 (fits 426 wedge and 440) factory cast iron dual four barrel intake. No carbs or spacers. Excellent condition. $350 or offer. Will consider any offer or partial trade.

Appears to be an over the counter piece as opposed to originally installed on a car due to casting date.


Attachments
DW279241.JPG

DW279244.JPG



Top
#2598061 - 12/28/18 02:23 PM Carter 4962S Carburetor $25.00 + Shipping [Re: moparts]
Powerflow Online   content
super stock

Registered: 07/31/06
Posts: 790
Loc: New Jersey
Here's a used Carter BBD 4962S carburetor for your 1970-71 Mopar with a 383 engine. In storage many years. Looks complete except for choke pull-off link. Should be cleaned/rebuilt before use. May fit other years/models as well. Let me know your zip code and I'll figure out shipping. PayPal is fine. Best contact is via Moparts PM.

Thanks for looking!
Harold


Attachments
4962S 1.JPG

4962S 2.JPG

4962S 3.JPG




Edited by Powerflow (12/28/18 02:29 PM)

Top
#2598821 - 12/30/18 12:11 PM Re: For Sale - Big Block Engine - 4th Quarter [Re: moparts]
moparpro Online   content


Registered: 03/08/15
Posts: 470
Loc: georgia
Contact the seller via pm or e-mail. This is not a discussion forum.


Edited by tboomer (12/30/18 01:59 PM)
Edit Reason: not a discussion board

Top
Page 1 of 6 1 2 3 4 5 6 >

Advertisement
Forum Stats
25,700 Registered Members
32 Forums
196,767 Topics
2,305,588 Posts

Most users ever online: 1,424 @ 06/20/18 07:18 PM
Moparts Newest Topics
When you are bored in the Iowa winter. Mopar related!
by tboomer
01/20/19 10:57 AM
Best Way to Strip and Refinish Steel Rim
by floyd
01/20/19 10:49 AM
2002 24valve, I need a little more power
by RV2
01/20/19 10:44 AM
Help ID Manual Trans Pedals
by floyd
01/20/19 10:42 AM