Re: headers that fit?
[Re: marcjames]
#2520036
07/10/18 03:52 PM
07/10/18 03:52 PM
|
Joined: Jan 2003
Posts: 4,267 Morrow, OH
markz528
master
|
master
Joined: Jan 2003
Posts: 4,267
Morrow, OH
|
Hookers fit pretty decent in a 67 with a 440. I run 5209 (2 inch).
67 Coronet 500 9.610 @ 139.20 mph 67 Coronet 500 (street car) 14.82 @ 94 mph 69 GTX (clone) - build in progress......
|
|
|
Re: headers that fit?
[Re: marcjames]
#2520040
07/10/18 04:01 PM
07/10/18 04:01 PM
|
Joined: Jan 2003
Posts: 14,479 So. Burlington, Vt.
fast68plymouth
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 14,479
So. Burlington, Vt.
|
In my 68 satellite with RB motor I’ve run 1-3/4 Eagle(from the 80’s), and Hooker 2” super comp. I had some SR heads on a RB motor in the car, and installed the TTi 2-2 1/8” step headers for the Indy heads. They were the easiest of the 3 to install.
On my 383 B engine I ran Hooker Competition headers , which are 1-7/8”.
In my car, the Eagles and Hooker Comps were actually harder to get into the car than the big headers, but once installed I felt all four sets fit pretty well.
If you have angle plug heads, the TTi’s generally have the best plug clearance.
68 Satellite, 383 with stock 906’s, 3550lbs, 11.18@123 Dealer for Comp Cams/Indy Heads
|
|
|
Re: headers that fit?
[Re: marcjames]
#2520046
07/10/18 04:09 PM
07/10/18 04:09 PM
|
Joined: Jan 2003
Posts: 13,319 Marion, South Carolina [><]
an8sec70cuda
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 13,319
Marion, South Carolina [><]
|
CHIP '70 hemicuda, 575" Hemi, 727, Dana 60 '69 road runner, 440-6, 18 spline 4 speed, Dana 60 '71 Demon, 340, low gear 904, 8.75 '73 Chrysler New Yorker, 440, 727, 8.75 '90 Chevy 454SS Silverado, 476" BBC, TH400, 14 bolt '06 GMC 2500HD LBZ Duramax
|
|
|
Re: headers that fit?
[Re: markz528]
#2520183
07/10/18 08:23 PM
07/10/18 08:23 PM
|
Joined: Aug 2003
Posts: 43,007 Bend,OR USA
Cab_Burge
I Win
|
I Win
Joined: Aug 2003
Posts: 43,007
Bend,OR USA
|
Hookers fit pretty decent in a 67 with a 440. I run 5209 (2 inch). I have the same Hooker headers on my 1966 Dodge Coronet Deluxe two door sedan with a stock iron headed (452 heads) 440 motor and those headers fit well and weren't hard to install with the new motor, it was a slant six three speed stick car before so I swapped the K member out to a 1968 B Body V8 K member into it also
Last edited by Cab_Burge; 07/11/18 03:54 AM.
Mr.Cab Racing and winning with Mopars since 1964. (Old F--t, Huh)
|
|
|
Re: headers that fit?
[Re: marcjames]
#2520245
07/10/18 10:11 PM
07/10/18 10:11 PM
|
Joined: Nov 2010
Posts: 3,696 jersey
Spaceman Spiff
master
|
master
Joined: Nov 2010
Posts: 3,696
jersey
|
anything other then Cyclone or blackjack.
526 cubes of angry wedge, pushbutton shifted, 9 passenger killer!
|
|
|
|
|