Topic Options
#2475771 - 04/01/18 11:13 PM For Sale - Race Cars - 2nd Quarter
moparts Offline


Registered: 01/19/03
Posts: 13939
Loc: Norwich CT USA
up

Top
#2476749 - 04/03/18 11:33 AM Re: 1973 Plymouth Duster 582 ci [Re: moparts]
Al_Alguire Offline


Registered: 01/20/03
Posts: 16695
Loc: Rockville MD & Las Vegas
No longer for sale


Looking to sell out 235" Racetech 4 link dragster. My son is going to concentrate on the shop more so we don't need the car right now. Car be purchased many ways, but only as a roller. Can purchase less engine, less engine and trans etc. Car has won many rounds of racing over the years but he needs to concentrate on work for awhile. Set up for a BBM or a BBC. Have both mid and motor plates also have headers. Trans in a FTI with a Reid case. Rear is a 9" ford with Strange aluminum center section. Biondo mega 450, Biondo dial board and switch panel, Autometer gauges, American Racing front wheels with M/T tires. Price depends on how its purchased.

Car has been 1.03 60' with a 572" B1 in it in Vegas with a small carb and timing backed down. In Salt Lake it went 7.54 with the timing in it and bigger carb at 9000' DA. Car went 8.teens with a 446 pump gas motor and Indy heads in Las Vegas. It is a very consistent piece and works very well. Won three races last year with a rookie driver.

*********PENDING*************

PM me here or email me at b1valiant@hotmail.com or call me at 7 0 7 9 8 0 2 1 6 7. If I don't answer leave a message as I have poor cell service when at our DC condo.







Edited by Al_Alguire (04/19/18 11:29 AM)
_________________________

"I am not ashamed to confess I am ignorant of what I do not know."

"It's never wrong to do the right thing"

Top
#2478020 - 04/05/18 06:37 PM Re: 1973 Plymouth Duster 582 ci [Re: Al_Alguire]
earthmover Offline
top fuel

Registered: 08/11/07
Posts: 2432
Loc: nc
9 0 0
Contact Seller
Testing the waters see if anyone would like to have it ..reason for this is I've found me a 1967 2door sport fury 3 in pretty good shape..auto in the floor wide block 318 I've been looking a fury for a while ..

Moser race axles 8 3/4rear big bolt pattern
8 gal cell
B/m shifter
Mad 6al
Trans cooler
4.56 gear that needs saying up
489 case pos.
Tech and gauges
Frame connectors
Mp 02/03 springs
2 hoods factor and 1 with hood scoop
Mini tube


Front floor pans need replace
3500.00
With 400 motor never been started since redone.
Crane hayd. Cam aluminium intake adjustable rockers

Can't seem to post pic..pm email will send pic
Located in nc outside Raleigh


Edited by earthmover (04/05/18 06:38 PM)

Top
#2478982 - 04/07/18 05:45 PM Re: For Sale - Race Cars - 2nd Quarter [Re: moparts]
eh100 Offline
top fuel

Registered: 01/31/03
Posts: 1655
Loc: Gainesville FL
Over 30 years of fun, time for someone else to play with it

64 Dodge A100


CHASSIC/DRIVETRAIN 2x3 tube frame...Capri struts...4:88 DANA with spool...Ladder Bars...Koni Alum Shocks...Weld Wheels...Harwood Fuel Cell...Twin Holley Blue Pumps...Autometer gauges...Autometer Ultimate II Tach...BTE PG W/Winter Bellhousing...Two BTE Contvers for 670 & 700 motor...Biondo Shift Actuator...TurboAction Shifter W/JEG Electric Shifter...Dedenbear Delay Box...Mopar MSD 7AL Ignition Box

BODY 5.5inch TopChop Channeled...Glass doors...Lexan Windows...Removable Front Spoiler...2600LBS

MOTOR 496 3/8 Stroker 400 Block...1/2 Filled...Reversed Cooling...Edelbrock Heads ported by Porter...Manley Rods...Mopar Race Dist...Milidon Oil System W/oil pan off Darrell Quenns TF car...383 Victor and a M1 Intakes...8896 Dominator...Comp Cams 637lift Roller...Crane Rockers

$7700 Went 6.18 last time out Busch_Bob@yahoo.com
_________________________
GO FOR A RIDE......GRILL CAM http://www.flickr.com/photos/busch_bob/8600312291/

Top
#2483488 - 04/16/18 07:27 AM Re: For Sale - Race Cars - 2nd Quarter [Re: 408Dust]
joez Offline
mopar

Registered: 01/19/03
Posts: 473
Loc: PA
1972 Dodge Challenger race car roller. SFI 25.5 mild steel chassis with stock front and rear frame rails. Fiberglass front end and deck lid. Has factory 1970 grill, headlights and tail lights for street appearance. Steel doors with working glass. Cowl hood with carbon pro stock style scoop.
Custom tubular k-member with flaming river mustang II rack and spindles. AVO double adjustable front coilovers, Qa1 adjustable rear coil overs, S&W ladder bars, diagonal link and splined anti roll. Chassis engineering wheelie bars. Wilwood disc brakes front and rear. Dana 60 with moser 35 spline spool and axles. Dewco pro-fin 3.73 pro gear. 15x11 holeshot rear wheels, Weld magnum front wheels.
Motor plate for BB Mopar. 2 3/8” custom headers with collector mufflers. ATI powerglide adapter midplate, flywheel.
Fiberglass stock appearing dash with autometer gauges, Stock door panels, Kirkey seat, firefox fire system, stroud chute, jaz 3 gallon fuel cell, dual nitrous bottle mount, laptop mount, quarter stick shifter MSD digital 7 programmable, hvc2 coil, strange low mounted master cylinder, afco radiator,
Last run with 528 B1MC low deck nitrous. Best ΒΌ mile 1.308/5.34@135.88mph/8.21@171.29mph. Best 1/8 mile 1.19/5.29@132.7mph @ 3,050lb Joe – nitrojoez@yahoo.com – 570-436-5544 $15,000 obo


Attachments
challenger.jpg



Top
#2485027 - 04/19/18 09:38 AM Re: For Sale - Race Cars - 2nd Quarter [Re: moparts]
bigdad Offline
Still Posting A Lot

Registered: 02/12/04
Posts: 29172
Loc: S.E. South Dakota !
FOR SALE

1967 Belvedere 2 door sedan

I just rebuilt about 85% of this car

Brand new 470 with Edelbrock Victor heads ( unported )
every part was new in the build, the 400 block was a super low mile
lightly used piece I was lucky enough to come across
it has all the right things done to it built by a very well know and respected performance shop in Carroll Iowa
https://www.facebook.com/demersperformance/

made 600 HP / 600 TQ on the dyno on some easy pulls


It has a 100% brand new Cope stage 2 727 with his trans brake
http://coperacingtranscom.ipage.com/?product=727-8-super-pro-ii-trans-brake

carbon fiber shield, brand new matched PTC convertor

Brand new front from Geerst Suspension
http://gerstsuspensions.com/products/front-suspension/


Just put on new coil overs on rear from Aldan

all new spool and 4.30 gears

New headers from TTI

It is ready to go to the track ..

why sell now ? Just found another car I want !

needless to say , as you can see by the list ..

I just put over 36,500 in the car


It should make me or someone else a great trouble free bracket car for years to come since its all new

B-body drag cars don't pop up often for sale like this one
( paint is a 20 footer)


I'll start at $38,000 -- Located near SIOUX FALLS, SD

pm me if you are interested and have the needed funds


Attachments
bluntwheelsup.jpg



Top
#2492049 - 05/04/18 02:11 PM 1968 Dodge Dart [Re: bigdad]
sixpacksteve Offline
super stock

Registered: 01/18/04
Posts: 1181
Loc: n.y.
68 Dodge Dart

68 block, 505" stroker
4.25 scat crank n H beam rods
12.5 flat top pistons
external oiling milodon pan
682 Bullet cam
Edelbrock victor max heads
T&D roller setup
indy max intake
1150 holley(redone by Thumper)
MSD ignition system
hedman hustler headers
Coan full race trans w/transbrake
Ultimate 8" 5500 convertor
custom strange driveshaft
Dana 60 rear 4:10
M/T slicks 29.5x10.5
Cage NOT certified
seat belts are 6/17
can make streetable w/exhaust
has glass fenders and hood
has super stock seats and aluminum brackets by Gary Ball
has steel bumpers,brackets rear seat etc..
Engine has just been rebuilt Only 9 Passes
Trans has just been been Rebuilt Only 4 Passes

its ready to go Racing!

Cars best so far 9.70 at 138 mph
60 ft. 1.39
asking 25K i have at least that much just in receipts


Attachments
PA280755.JPG




Edited by sixpacksteve (05/04/18 02:14 PM)

Top
#2493327 - 05/07/18 05:23 PM Re: For Sale - Race Cars - 2nd Quarter [Re: moparts]
71blackdemon Offline
enthusiast

Registered: 02/16/12
Posts: 241
Loc: Kentucky
1968 Dodge Dart roller no engine no transmission the car has a Dana 60 with 488 gears and 35 spline Moser axles with aftermarket disc brakes the K member is a spool mount with disc brakes and all new bushings the springs have been moved in and mini tubbed I'm asking $8,500 or best offer


Attachments
KIMG0798.JPG

KIMG0796.JPG

KIMG0787.JPG

KIMG0752.JPG



Top
#2495407 - 05/13/18 06:28 AM Re: For Sale - Race Cars - 2nd Quarter [Re: moparts]
572_HEMI_Cuda Offline
enthusiast

Registered: 12/30/04
Posts: 298
Loc: Shelton, Ct.


1970 Dodge Dart street/race car for sale. Small block 417", W8 heads, SV1. T400, Ultimate converter. 9" fab rear. Built by Mark Markow @ MRC. Fiberglass doors, hood and trunk. AlterKation front end.
Has run 8.80 @ 154 at LVD in the heat with street tires and exhaust. Car has about 18 runs on it. Haven't even begun to tune it, plenty more in it. 8.50 cert done in May 2017. Currently registered in CT.
Beautiful car, cost over 100k to build. Only the best parts.
52k or best offer
More pics at http://seifertbros.com/70_dart.html

PM or email:steve@seifertbros.com for more info.
_________________________
Our Projects www.seifertbros.com

Top
#2497020 - 05/16/18 10:07 PM 70 Cuda Tube Chassis Roller [Re: moparts]
sgcuda Offline
master

Registered: 01/28/05
Posts: 3815
Loc: Charlotte, North Carolina
Sorry guys. Wife said "Not For Sale!"
You guys have seen my build on this car. So close to being done, but things happen in life, so it's up for sale. To give a quick run down: 1970 Cuda 440-6. 2x3 M/S frame rails and Smith RaceCraft M/S Ladder Bar crossmember. Full C/M cage ready to cert for 7.50's. Smith RaceCraft Outlaw C/M Ladder bars. Rebuilt Strange D/A aluminum rear shocks with fresh dyno sheet. Dana 60 narrowed with new ends, spool and bearing kit from Dr. Diff. Richmond 4.10 gears. New Moser 35 spline axle shafts. 5/8 drive studs. New Strange cover. New Wildwood rear brake kit. New Strange S/A aluminum front struts with H/D 4 piston brakes and C/M arms. New Jegs aluminum steering column kit. New Summit seat and cover. Unlimited fiberglass bumpers, fenders, front and rear valances, header panel, hood, trunk, doors, scoop. C/E quick release door hinge kit and glass nose mounting kit. C/E big block engine plate. Driveshaft Shop driveshaft with 1350 spicer joints and M/W yoke. 15x4 and 15x15 Welds. OEM grill, tail lights, outer door handles and latches, roof, quarters. Have Dzus kits for finishing front end mounting. Body unbolts from chassis with 6 bolts on rocker sills and 2 bolts at rear panel. Needs completion. Asking $14,000. Listening to offers. Really don't need any trades, but might take Stealth/Avenger body as partial trade for future project. PM me here or text me at Seven04-Four58-Three734.


Attachments
013a09f9a961c827f899397c799640dc340352dfcd.jpg

01b59f173141807d2d187636a1a3717e5d5f39d25d.jpg

015edd0592b91265e1a7ed3ce31ee3e22173fc7cd2.jpg

0105ae450a584f411c7ffae05a2659eac0a3b56396.jpg




Edited by sgcuda (05/17/18 10:14 PM)

Top
#2498483 - 05/20/18 11:22 PM 1970 Cuda [Re: sgcuda]
tonys68dart Offline
member

Registered: 04/19/06
Posts: 67
Loc: oroville, ca
1970 Cuda Super Gas/Street, Cert. to 8.50, best pass of 9.55 @ 139. Car weighs 3050. Fiberglass hood and decklid. Lexan side windows. Powdercoated interior. 470 RB, .590 purple cam, milodon gear drive. Bulldog heads, Rons terminator fuel injection with primer. Also has gas fuel system to start and warm up car. 10 gallon fuel cell in trunk with aeromotive pump. 16 volt battery with alternator. MSD digital 7, biondo mega 450, K&R throttle stop, PPI air shifter, FAST 02, EGT. Dana 4.56, ladder bars. Much more, call if interested. 5305211651 Tony 40k


Attachments
2D0BD99B-AC01-40FB-8E96-9D50332EA404.JPG

cuda.JPG

F18E632D-0FEE-414A-A31D-18B1B240A4DD.JPG



Top
#2498777 - 05/21/18 07:08 PM Re: 90 Daytona rolling chassis [Re: moparts]
rt66jim Offline
master

Registered: 01/19/03
Posts: 3947
Loc: Joplin, Mo
90 Daytona Chris Alston MS rolling chassis. Car has less than 25 runs on it since new. Has been certified to 8.50 but is expired. 4 link 83/4 rear 4.30 ratio. Moser spool and caps on both brgs billet axles. Single adjustable rear coil overs. Front struts and brakes are Strange. Lexan windows. All the tin work is done except for the doors. 5 gal aluminum fuel cell. Griffin radiator. I have both BB & SB mopar motor and mid plates. GY front tires and Phoenix rears. Headers are currently SB. But I have the flanges to change them back to BB. This car runs nice and straight. Reason for sale. I'm ready to quit. If interested call me and I will tell you how to view more pics. $10000 OBO Jim 417-317-6863


Edited by rt66jim (05/21/18 07:16 PM)
_________________________

Top
#2499525 - 05/23/18 01:36 PM Re: For Sale - Race Cars - 2nd Quarter [Re: moparts]
Raymond Offline
member

Registered: 09/14/09
Posts: 72
Loc: Maryland, USA
FOR SALE.1981 DODGE OMNI,4 LINK CHASSIS CAR
DANA,4W DISC.CHUTE,CERTIFIED.394M.S.B
98MM TURBO.COAN TH400/BRAKE.BUMP BOX.
4BOLT X BLOCK W5 HEADS ALL THE BEST PARTS.
RUNS CONS.LOW 8S AT 3/4 POWER.
MUST SELL-RETIRED.
$18K WILL ACCEPT TRADES OR SEPARATE.

Top

Advertisement
Sponsored Link
Forum Stats
25,298 Registered Members
32 Forums
189,466 Topics
2,209,431 Posts

Most users ever online: 882 @ 03/05/17 10:15 PM
Moparts Newest Topics
Sneak peek pecker extension
by WHITEDART
28 minutes 43 seconds ago
More volcanic activity _ now mt. st. helens vicinity
by srt
52 minutes 55 seconds ago
1970 Dart GT on eBay
by grancuda
53 minutes 58 seconds ago
This Power wagon is just AWESOME!
by Rhinodart
59 minutes 30 seconds ago