Page 3 of 4 < 1 2 3 4 >
Topic Options
#2483056 - 04/15/18 11:33 AM Re: For Sale - Race Parts - 2nd Quarter [Re: moparts]
Mtn Thunder Offline
member

Registered: 11/01/09
Posts: 39
Loc: Tehachapi, Ca.
For Sale : NEW Demon 750 drag race carb. Set up as drag race only.
Comes with instructions and specs. Never used.
$500 shipped from Tehachapi, Ca.
Contact me here in a PM.
Mike


Attachments
100_3468.JPG

100_3469.JPG



Top
#2483248 - 04/15/18 06:04 PM BG Race Demon RS "825" 4150 carburetor [Re: Mtn Thunder]
BradH Offline
I Live Here

Registered: 01/30/03
Posts: 13635
Loc: Valhalla... eventually
I have too many carbs! It's time to thin out the herd #1!

BG Race Demon RS "825" 4150 carburetor in very nice used condition:
* 1 Race Demon RS main body w/ blue 1.425" venturi sleeves and .160"-leg downleg boosters
- NOTE: Main body has been drilled & tapped for replaceable TSRs (Transition Slot Restrictions)

* Race Demon billet 5-emulsion-hole metering blocks with replaceable emulsion, IFR & PVCR circuits
- IFRs can be installed in either the original "high" location or in the recommended "low" location that may improve idle characteristics

* Race Demon RS fuel bowls:
- standard primary & notched secondary floats for jet extensions
- new Holley .120" N&S
- new alcohol-compatible GFLT accel pump diaphragms
- #6 AN male fuel fittings

* Race Demon RS 1.75"-throttle base plate w/ thinned shafts & replaceable idle air bypass jet; comes with 3 sizes of idle air bypass jets:
- .197", approx same area as 4 x .100" bypass holes
- .213", approx same area as 4 x .110" bypass holes
- .228", approx same area as 4 x .120" bypass holes

* "Spares kit":
- extra drill-to-size emulsion jet blanks & extra drill-to-size IFR/IAB/MAB/TSR blanks if needed for tuning changes from supplied baseline
- extra fuel bowl & metering block gaskets
- primary & secondary jets 2#s richer & leaner from supplied baseline

* The baseline tune provided will be one that I've used on my 600+ HP 440 Mopar street/strip car

BUYER MUST EXPECT THAT ADDITIONAL TUNING FOR THEIR SPECIFIC COMBINATION WILL BE REQUIRED!


The "Nobody wants any surprises!" details:
* All fuel bowl screw holes were heli-coiled originally from BG; however, 2 of the BG-installed heli-coils pulled out
- I replaced the two stripped coils with 6mm x 1.5 inserts because the the repairs required slightly oversize inserts to hold
- Therefore, six (6) fuel bowl screws are the standard 12-24 w/ 1/4" socket-head & two (2) primary-side are 6mm x 1.5 w/ 5mm socket-head

* The venturi sleeves have been shortened approx. .020" to remove a small mismatch where the tops of the sleeves sat slightly higher than the main body; lowering the sleeves by this amount smoothed the transition from the main body into the venturi sleeves

* The secondary accel pump nozzle screw is shortened slightly because a standard-length screw keeps the check needle from lifting fully off its seat for some reason


The price is $575 SHIPPED to the lower 48 US states. I accept USPS money orders and cash. Sorry, NO PayPal or international sales.

Due to the nature of race engine parts, this carburetor is offered for sale "As Is" w/ no express or implied warranty.

Please PM me here, or text 7-zero-3 - 3-one-7 - 7-nine-8-seven... Thanks!

>> WARNING: SCAMMERS WILL NOT BE TREATED POLITELY <<


Attachments
BG Race Demon RS 825_sm.png


_________________________
"Do what you can, with what you have, where you are." - Theodore Roosevelt

“Money talks. Sometimes all it says is ‘Goodbye’.” - Unknown

Top
#2483250 - 04/15/18 06:05 PM Holley Ultra HP "950" 1.60" v Annular "KIT" [Re: BradH]
BradH Offline
I Live Here

Registered: 01/30/03
Posts: 13635
Loc: Valhalla... eventually
I have too many carbs! It's time to thin out the herd #2!

Holley Ultra HP "950" 1.60" venturi carburetor converted to annular boosters in very nice used condition. NOTE: This will be sold as a PARTS KIT to be assembled and tuned for the end user's application!

Although I did test it briefly using different boosters and metering blocks than will be included here, I didn't manage to get it sorted out to my satisfaction. The change in boosters and metering blocks are intended to return it to a more "standard" set of parts from which to tune the new combination.

Included (parts are used, unless noted otherwise):
- Holley Ultra HP "950" 1.60" venturi aluminum main body equipped with new BLP billet 12-hole x .600" ID annular boosters
--> NOTE: Main body has been drilled & tapped for replaceable TSRs (Transition Slot Restrictions)

- Holley Ultra H/XP "950" billet base plate w/ factory-slabbed throttle shafts

- New Holley Ultra H/XP billet 5-emulsion-hole metering blocks with replaceable emulsion, IFR & PVCR circuits and ~ .143" angle channels
--> NOTE: IFRs can be installed in either the original "high" location or in the recommended "low" location that may improve idle characteristics

- Holley Ultra H/XP fuel bowls:
- standard primary & notched secondary floats for jet extensions
- Holley .120" N&S
- alcohol-compatible GFLT accel pump diaphragms
- #6 AN male fuel fittings

Additional parts to help complete assembly:
- fuel bowl & base plate fasteners
- selection of pre-drilled & blank emulsion/PVCR jets & IFR/IAB/MAB/TSR bleeds
- selection of primary & secondary jets that should be "in the ballpark" for initial testing
- new fuel bowl & metering block gaskets
- new stainless steel accel pump discharge check needles & high-flow discharge screws
- .031" "squirters"
- NOTE: No primary power valve or secondary power valve plug will be provided

BUYER MUST EXPECT THAT TUNING FOR THEIR SPECIFIC COMBINATION WILL BE REQUIRED!


The price is $525 SHIPPED to the lower 48 US states. I accept USPS money orders and cash. Sorry, NO PayPal or international sales.

Due to the nature of race engine parts, this carburetor kit is offered for sale "As Is" w/ no express or implied warranty.

Please PM me here, or text 7-zero-3 - 3-one-7 - 7-nine-8-seven... Thanks!

>> WARNING: SCAMMERS WILL NOT BE TREATED POLITELY <<


Attachments
HLY UHP 1.6 AN hdwe.jpg




Edited by BradH (04/16/18 12:15 PM)
_________________________
"Do what you can, with what you have, where you are." - Theodore Roosevelt

“Money talks. Sometimes all it says is ‘Goodbye’.” - Unknown

Top
#2483320 - 04/15/18 08:01 PM New Schubeck lifters. SOLD [Re: moparts]
B1duster Offline
master

Registered: 03/12/05
Posts: 2712
Loc: NY
New set of Schubeck solid composite face .903 Mopar lifters. $500 plus shipping from NY 12569


Edited by B1duster (04/16/18 09:26 PM)

Top
#2483324 - 04/15/18 08:09 PM NOS new W2 Holley Pro Dominator Tunnel Ram [Re: moparts]
B1duster Offline
master

Registered: 03/12/05
Posts: 2712
Loc: NY
Never bolted down or modified with dual 4150 top and gasket. $699 plus shipping from NY 12569.

Top
#2483335 - 04/15/18 08:20 PM new PRW 1.6 SBM rockers with hold downs [Re: moparts]
B1duster Offline
master

Registered: 03/12/05
Posts: 2712
Loc: NY
New set of PRW 1.6 rockers with hold downs. Cost $400 new, $250 plus shipping from NY 12569


Attachments
99328103-AA21-4F88-B978-92DCE4DDF90C.jpeg

1A64FB82-B9A7-49F8-ABBA-35A803871966.jpeg



Top
#2483396 - 04/15/18 10:35 PM Re: new PRW 1.6 SBM rockers with hold downs [Re: moparts]
sunroofgtx Offline
I Live Here

Registered: 07/03/03
Posts: 12113
Loc: Cleveland
20 Gallon Aeromotive Stealth Fuel Tank and Pump 20 gallon New Aeromotive Eliminator Stealth Fuel Cell Brand new never used fuel cell and all fittings to install 216-224-3667 $1200 complete, with all fittings. Saving over $500!!
https://www.aeromotiveinc.com/product/20g-eliminator-stealth-fuel-cell/ North Ridgeville, Ohio 216-224-3667



_________________________
Join the quickest team in motorsports. Team FireCore. CustomWiresets.com

Top
#2483411 - 04/15/18 11:05 PM Re: new PRW 1.6 SBM rockers with hold downs [Re: moparts]
sunroofgtx Offline
I Live Here

Registered: 07/03/03
Posts: 12113
Loc: Cleveland
Innovators West Big Block Mopar Balancer, with magnets for a crank trigger. New $685 $500 shipped 216-224-3667 Rick in Cleveland



_________________________
Join the quickest team in motorsports. Team FireCore. CustomWiresets.com

Top
#2483413 - 04/15/18 11:10 PM Re: new PRW 1.6 SBM rockers with hold downs [Re: moparts]
sunroofgtx Offline
I Live Here

Registered: 07/03/03
Posts: 12113
Loc: Cleveland
Set of original vintage Centerline Wheels. 15X10 mounted with M/T 28 X 12.5 and front are 15 X 3.5 ( I think) mounted on Goodyear Eagles. Rick @ 216-224-3667 Cleveland $850 obo Rears have a ton of life left. Front--15 X 4.5 Mopar/Ford rears have 4.5 backspace. These were on my 71 B Body.



_________________________
Join the quickest team in motorsports. Team FireCore. CustomWiresets.com

Top
#2483712 - 04/16/18 02:58 PM demon carbs [Re: moparts]
blue_stocker Offline
super stock

Registered: 11/04/03
Posts: 1015
Loc: What's left of GOD's country, ...
820 race demon carb, bought a few years back but haven't used it. Nice shape but needs a kit, pretty clean, $300 plus shipping from Nothern calif.

850 Mighty Demon w/annular boosters, excellent condition, clean and original, $450 plus shipping from Northern calif.

PM here if interested, thanks.
_________________________
I predict future happiness for Americans if they can prevent the government from wasting the labors of the people under the pretense of taking care of them.
Thomas Jefferson

Top
#2483762 - 04/16/18 04:20 PM Dana 60 and 9” Ford ring and pinions [Re: Doug Caviness]
JesseR Offline
mopar

Registered: 04/06/04
Posts: 408
Loc: Mountain City, TN
Yukon gear, Dana 60 5:88 gear, like new, $100

Richmond 9” 5:14 gear, like new $100, plus shipping

Pm me here
_________________________
82' dodge pickup with a 499 low deck

Top
#2483765 - 04/16/18 04:39 PM Re: For Sale - Race Parts - 2nd Quarter [Re: moparts]
AndyF Offline
Too Many Posts

Registered: 01/20/03
Posts: 23815
Loc: Oregon
SALE PENDING - Milodon deep oil pan for BB or Hemi. Part number 31010 with 18330 pickup. I used these parts for a few dyno pulls and then switched to a different pan so the parts have some wear on them but the pan does not have any dents in it. $175 for both parts plus shipping. PayPal preferred or money order is fine. PM here on the board.


Attachments
DSC_2259 (Large).JPG




Edited by AndyF (04/17/18 09:18 PM)

Top
#2483766 - 04/16/18 04:41 PM Re: For Sale - Race Parts - 2nd Quarter [Re: moparts]
AndyF Offline
Too Many Posts

Registered: 01/20/03
Posts: 23815
Loc: Oregon
Swivel pickup setup for SB Mopar engine. Milodon 19325 and 19331 used together make a deep swivel pickup. Have to use the matching Milodon pan or a custom made deep pan. $150 for both parts new in package. PayPal or money order. PM me on the board.


Attachments
DSC_1990 (Large).JPG



Top
#2483767 - 04/16/18 04:43 PM Re: For Sale - Race Parts - 2nd Quarter [Re: moparts]
AndyF Offline
Too Many Posts

Registered: 01/20/03
Posts: 23815
Loc: Oregon
SOLD - Mopar bronze oil pump drive gear for SB Mopar. Mopar wants $250 for these gears these days. I'll sell this one for $100 plus a few bucks for shipping. It has not been used. I'm selling all of my SB stuff since I'm not going to build another one. PayPal or money order. PM me on the board.


Attachments
DSC_1991 (Large).JPG




Edited by AndyF (04/16/18 09:44 PM)

Top
#2483770 - 04/16/18 04:45 PM Re: For Sale - Race Parts - 2nd Quarter [Re: moparts]
AndyF Offline
Too Many Posts

Registered: 01/20/03
Posts: 23815
Loc: Oregon
Holley Ultra 950 carb. This is an early 950 carb with the smaller venturi. It doesn't flow 950, probably more like 800 cfm. Braswell called this a 750 Hi Flow which is probably a better name for it. Very nice carb, super low miles. I had this on my low deck 512 for a little while and also used it as a dyno carb. I'm switching everything over to EFI so the carbs need to go. Asking $500 for this one plus some shipping. PayPal or money order. PM me on the board.


Attachments
DSC_2265 (Large).JPG



Top
#2483771 - 04/16/18 04:48 PM Re: For Sale - Race Parts - 2nd Quarter [Re: moparts]
AndyF Offline
Too Many Posts

Registered: 01/20/03
Posts: 23815
Loc: Oregon
Cast aluminum oil pan. Original marine engine part but I've seen guys use these on drag cars, rails, altered cars, etc. $100 plus shipping. Probably worth a lot more to the right guy but I don't know who the right guy is. The pan is heavy so shipping will cost some bucks. PayPal or money order. PM me on the board.


Attachments
DSC_0646 (Large).JPG

DSC_0647 (Large).JPG



Top
#2483873 - 04/16/18 07:48 PM Re: For Sale - Race Parts - 2nd Quarter [Re: moparts]
AndyF Offline
Too Many Posts

Registered: 01/20/03
Posts: 23815
Loc: Oregon
SALE PENDING - Auto Rod Controls switch panel. This is an older model but kind of like the ARC 3100 which is still available. This panel has been sitting in a box on the shelf for a long time. I finally decided I wasn't going to use it so off to market it goes. Asking $75 plus shipping. The new ones are around $200 depending on the model.

This panel has a long #6 wire to connect to the battery. It will run ignition, starter, two fuel pumps, lights and cooling fans or a water pump. A really nice way to solve the wiring problems for a bracket type of car. PayPal or money order, PM me on the board.


Attachments
DSC_2339 (Large).JPG

DSC_2340 (Large).JPG




Edited by AndyF (04/17/18 09:18 PM)

Top
#2483874 - 04/16/18 07:50 PM Re: For Sale - Race Parts - 2nd Quarter [Re: moparts]
AndyF Offline
Too Many Posts

Registered: 01/20/03
Posts: 23815
Loc: Oregon
SALE PENDING - Isky Rev kit for BB Mopar engines. Designed for RB blocks. I think you have to use the special Isky roller lifters for this to work properly. Kit is complete and unused. Asking $50 plus shipping. PayPal or money order. PM me on the board.


Attachments
DSC_2338 (Large).JPG




Edited by AndyF (04/20/18 08:59 PM)

Top
#2484021 - 04/17/18 12:49 AM Re: For Sale - Race Parts - 2nd Quarter [Re: AndyF]
72sat Offline
enthusiast

Registered: 03/10/04
Posts: 271
Loc: St.Louis ,Mo.
I have a set of pro comp aluminum heads. 2.25 titanium intake valves. 1.81 Manley stainless steel exhaust valves. Valve stems are 11/32. titanium valves will need lash caps. CNC'd ports, with epoxy filler. Intake ports flow 364 cfm after CNC, 384 after hand blending, see pics for flow sheet. 1st column is flow after CNC, 2nd is after hand blend. $2500 can not post pics,contact me and I will send photos 314-687-9584


Edited by 72sat (04/17/18 12:56 AM)

Top
#2484425 - 04/17/18 09:27 PM Re: For Sale - Race Parts - 2nd Quarter [Re: moparts]
AndyF Offline
Too Many Posts

Registered: 01/20/03
Posts: 23815
Loc: Oregon
SOLD - New in box, Comp Cams solid roller cam for BB Mopar. 271/276 @ 050. Lift is 0.705/0.690 with a 1.50 rocker arm. This cam should work nice in a stroker bracket type engine with decent compression and good heads. $200 plus shipping. PayPal or money order. PM me on the board.

Cam has 1811/1841 lobes on 108 center.


Attachments
DSC_1678 (Large).jpeg




Edited by AndyF (04/21/18 12:10 PM)

Top
Page 3 of 4 < 1 2 3 4 >

Advertisement
Sponsored Link
Forum Stats
25,253 Registered Members
32 Forums
188,915 Topics
2,203,130 Posts

Most users ever online: 882 @ 03/05/17 10:15 PM
Moparts Newest Topics
95RON as a standand octane at the pump?
by mopar dave
Today at 10:42 AM
For those who can't get enough ... new Ramcharger
by KISSAlien
Today at 10:21 AM
8 years under a cover "Forever Young" Diego is back!
by Diego_Ted
Today at 09:51 AM
Need help identifying Mopar performance part number
by WHITEDART
Today at 09:45 AM