Topic Options
#2462943 - 03/07/18 10:49 PM Removing center link?
500ciBee Offline
member

Registered: 05/03/05
Posts: 98
Loc: Ontario, Canada
I need to remove the center link to swap out the headers on my Bee. The center link passes between the tubes of the headers. I'm not sure what is the best method to getting the center link off. I've tried hitting it about as hard as I think is safe. What do you guys suggest?


Edited by 500ciBee (03/07/18 10:51 PM)
_________________________
1970 Super Bee prostreet. 383, SMR 727, Dana 60 4:88. Building a 512 low deck.

Top
#2462951 - 03/07/18 11:16 PM Re: Removing center link? [Re: 500ciBee]
GoodysGotaCuda Offline
5.7L Hemi, 6spd

Registered: 11/23/04
Posts: 24520
Loc: Texas
_________________________
1972 Barracuda - 5.7L Hemi, T56 Magnum 6spd - https://www.facebook.com/GoodysGotaHemi
1976 Dodge Warlock - "Her Truck" - 360/727 2wd
1969 Dodge Dart Custom Sedan - Grandma Edition - 318/904
2016 Subaru WRX - E30 Tune ~320whp

Top
#2463236 - 03/08/18 03:37 PM Re: Removing center link? [Re: 500ciBee]
500ciBee Offline
member

Registered: 05/03/05
Posts: 98
Loc: Ontario, Canada
Thanks! I'll pickup one those.
_________________________
1970 Super Bee prostreet. 383, SMR 727, Dana 60 4:88. Building a 512 low deck.

Top
#2464185 - 03/10/18 05:36 AM Re: Removing center link? [Re: 500ciBee]
BigBlockMopar Offline
master

Registered: 01/22/03
Posts: 3412
Loc: The Netherlands
You can usually pop ball joints with use of two large (±5 lbs) hammers.
Put one (the largest) hammer behind and hit the metal from the front.
Of course you don't whack the balljoint itself, but the part that it's protruding.

Leave the nut loose on the threads in case you hit it wrong.
_________________________
BigBlockMopar.com


Top
#2468170 - 03/18/18 03:10 PM Re: Removing center link? [Re: 500ciBee]
500ciBee Offline
member

Registered: 05/03/05
Posts: 98
Loc: Ontario, Canada
I bought a ball joint separator but there is no way the tool will fit between the idler arm and center link. I've hit it enough that I think it should have come apart. Should I remove the idler from the frame?


Attachments
image.jpg


_________________________
1970 Super Bee prostreet. 383, SMR 727, Dana 60 4:88. Building a 512 low deck.

Top
#2468198 - 03/18/18 04:15 PM Re: Removing center link? [Re: 500ciBee]
GoodysGotaCuda Offline
5.7L Hemi, 6spd

Registered: 11/23/04
Posts: 24520
Loc: Texas
May need to tap it in a little. Mine worked perfectly..
_________________________
1972 Barracuda - 5.7L Hemi, T56 Magnum 6spd - https://www.facebook.com/GoodysGotaHemi
1976 Dodge Warlock - "Her Truck" - 360/727 2wd
1969 Dodge Dart Custom Sedan - Grandma Edition - 318/904
2016 Subaru WRX - E30 Tune ~320whp

Top

Advertisement
Forum Stats
25,627 Registered Members
32 Forums
195,543 Topics
2,287,465 Posts

Most users ever online: 1,424 @ 06/20/18 07:18 PM
Moparts Newest Topics
Looking For Kick Down Linkage Experience
by Rodder
12/11/18 11:12 PM
Battery ID from broadcast sheet
by 340cpe
12/11/18 10:47 PM
Lower cylinder damage,ok to run?
by RTSrunner
12/11/18 10:14 PM
77 charger. midnight charger?
by moparvinson
12/11/18 10:06 PM