Page 3 of 9 < 1 2 3 4 5 6 7 8 9 >
Topic Options
#2430796 - 01/07/18 08:28 PM Re: For Sale - Race Parts - 1st Quarter [Re: Plumb Wired]
Plumb Wired Offline
master

Registered: 01/20/03
Posts: 2696
Loc: Blue Ridge, VA
Aeromotive Fuel Filter #12612 -10AN bulkhead w/ 100 micron filter, brand new, only opened for pic, mounts inside your tank or cell, $70 shipped
PayPal (+3%) & USPS Money Orders accepted

email: mgray0918@verizon.net or pm me thru Moparts

Thanks,
Mike Gray


Attachments
Aeromotve 12612 Fuel Filter.JPG


_________________________
RIP Monte Smith

aka: OutlawFish
'98 Bickel Dodge Dakota PST

Top
#2430800 - 01/07/18 08:29 PM Re: For Sale - Race Parts - 1st Quarter [Re: Plumb Wired]
Plumb Wired Offline
master

Registered: 01/20/03
Posts: 2696
Loc: Blue Ridge, VA
9.00" - 9.56" Deck R3/Weber Belt Drive Motorplates, water jet cut from 1/4" T6061 aluminum. 36" wide centered for tube chassis application or marked for A-Body offset. Can be trimmed to fit any application. Use this plate along with Brian Smith (Smith Innovation) water pump spacers to complete the set up. Only 1 remaining in stock $175.00 shipped

PayPal (+3%) & USPS Money Orders accepted

email: mgray0918@verizon.net or pm me thru Moparts

Thanks,
Mike Gray


Attachments
Plumb Wired Weber Belt Drive Motorplate.jpg


_________________________
RIP Monte Smith

aka: OutlawFish
'98 Bickel Dodge Dakota PST

Top
#2430803 - 01/07/18 08:30 PM Re: For Sale - Race Parts - 1st Quarter [Re: Plumb Wired]
Plumb Wired Offline
master

Registered: 01/20/03
Posts: 2696
Loc: Blue Ridge, VA
Autometer Super-Lite LED shift lite #5333, new, $60 shipped

Autometer Ultra Lite 2 5/8" Gauge Brake Pressure #4426, mechanical, used, $50 shipped

Autometer temp sender #2252, 1/8" npt for use w/ electric water temp gauge, new, $15 shipped

VDO MegaLite shift light w/ chromoly mount fits 1 1/4" steering shaft w/ t-bolt clamp, used, $80 shipped

PayPal (+3%) & USPS Money Orders accepted

email: mgray0918@verizon.net or pm me thru Moparts

Thanks,
Mike Gray


Attachments
Autometer & VDO.JPG


_________________________
RIP Monte Smith

aka: OutlawFish
'98 Bickel Dodge Dakota PST

Top
#2430804 - 01/07/18 08:31 PM Re: For Sale - Race Parts - 1st Quarter [Re: Plumb Wired]
Plumb Wired Offline
master

Registered: 01/20/03
Posts: 2696
Loc: Blue Ridge, VA
Ritter fabricated aluminum W8 valve covers w/ fill bungs & vacuum pump fitting. The tops are slightly warped and I would recommend milling the flanges to assure a good gasket seal. I'll throw in a couple sets of used Fel-Pro gaskets, $200.00 shipped

Paypal (+3%) & US Postal Money Orders accepted

email: mgray0918@verizon.net or PM me thru Moparts

Thanks,
Mike Gray


Attachments
Ritter W8 Valve Covers.JPG


_________________________
RIP Monte Smith

aka: OutlawFish
'98 Bickel Dodge Dakota PST

Top
#2430805 - 01/07/18 08:32 PM Re: For Sale - Race Parts - 1st Quarter [Re: Plumb Wired]
Plumb Wired Offline
master

Registered: 01/20/03
Posts: 2696
Loc: Blue Ridge, VA
ARP #245-4307 12pt. Head Studs B1 Heads, NEW, $220 shipped

ARP #240-2501 12pt. Balancer Bolt, package has been opened, $28.00 shipped

ARP #200-2903 12pt. Flexplate Bolts, NEW, $14.00 shipped

PayPal (+3%) & USPS Money Orders accepted

email: mgray0918@verizon.net or pm me thru Moparts

Thanks,
Mike Gray


Attachments
ARP Mopar.JPG


_________________________
RIP Monte Smith

aka: OutlawFish
'98 Bickel Dodge Dakota PST

Top
#2430808 - 01/07/18 08:33 PM Re: For Sale - Race Parts - 1st Quarter [Re: Plumb Wired]
Plumb Wired Offline
master

Registered: 01/20/03
Posts: 2696
Loc: Blue Ridge, VA
Comp Cams BB Mopar Solid Roller, three bolt, older camshaft, used, very good condition, no cam card but here are the specs per Comp:
Intake: 288 @.050 / .483 lobe lift
Exhaust: 316@.050 / .480 lobe lift
114 lobe separation

Comp Cams Roller Lifters, .904 dia., centered, used, all rollers turn freely

Triple Springs, titanium retainers, locks (15), lash caps (8) (unknown brand, I assume Comp)

All came from an engine I purchased and parting out. Package deal all for $500.00 shipped

PayPal (+3%) & USPS Money Orders accepted

email: mgray0918@verizon.net or pm me thru Moparts

Thanks,
Mike Gray


Attachments
BBM Comp Cams #1.JPG

BBM Comp Cams #2.JPG

BBM Comp Cams #3.JPG




Edited by Plumb Wired (02/15/18 09:34 PM)
_________________________
RIP Monte Smith

aka: OutlawFish
'98 Bickel Dodge Dakota PST

Top
#2430810 - 01/07/18 08:34 PM Re: For Sale - Race Parts - 1st Quarter [Re: Plumb Wired]
Plumb Wired Offline
master

Registered: 01/20/03
Posts: 2696
Loc: Blue Ridge, VA
B1/MC valves, 2.400" x 5.500" x .3415 stem titanium intake (6) used, 1.780" x 5.400" x .3415 stem stainless exhaust (6) used, $400 for all shipped

PayPal (+3%) & USPS Money Orders accepted

email: mgray0918@verizon.net or pm me thru Moparts

Thanks,
Mike Gray


Attachments
B1-MC Valves.JPG




Edited by Plumb Wired (01/08/18 08:28 PM)
_________________________
RIP Monte Smith

aka: OutlawFish
'98 Bickel Dodge Dakota PST

Top
#2430812 - 01/07/18 08:35 PM Re: For Sale - Race Parts - 1st Quarter [Re: Plumb Wired]
Plumb Wired Offline
master

Registered: 01/20/03
Posts: 2696
Loc: Blue Ridge, VA
Misc. Nitrous:
Induction Solutions 1/4 Turn Valve #19705, w/ 6AN fittings, New, $55 shipped
Induction Solutions 1/4 Turn Valve Mount Tab #19809, New, $8 shipped
RJ Race Cars Aluminum Handle for 1/4 Turn Valve, New, $11 shipped
4" dia. Nitrous Pressure Gauge, used, $45 shipped
4ft. 6AN Line, NOS #15420, used, $35 shipped
1ft. 4AN Line, NOS #15210, used, $18 shipped
Edelbrock #72281 WOT Switch, 4500 carb, $30 shipped

PayPal (+3%) & USPS Money Orders accepted

email: mgray0918@verizon.net or pm me thru Moparts

Thanks,
Mike Gray


Attachments
Nitrous Misc.JPG

IS N2O Misc..JPG




Edited by Plumb Wired (01/13/18 08:21 PM)
_________________________
RIP Monte Smith

aka: OutlawFish
'98 Bickel Dodge Dakota PST

Top
#2430815 - 01/07/18 08:35 PM Re: For Sale - Race Parts - 1st Quarter [Re: Plumb Wired]
Plumb Wired Offline
master

Registered: 01/20/03
Posts: 2696
Loc: Blue Ridge, VA
Misc. Parts:
Stroud Large Chute Pack for large pilot style chute, used, good condition, $35 shipped

PayPal (+3%) & USPS Money Orders accepted

email: mgray0918@verizon.net or pm me thru Moparts

Thanks,
Mike Gray


Attachments
Stroud LG Chute Pack.JPG


_________________________
RIP Monte Smith

aka: OutlawFish
'98 Bickel Dodge Dakota PST

Top
#2430819 - 01/07/18 08:45 PM Re: For Sale - Race Parts - 1st Quarter [Re: Plumb Wired]
Plumb Wired Offline
master

Registered: 01/20/03
Posts: 2696
Loc: Blue Ridge, VA
Jegs 2 1/2lb. CO2 Bottle #60207, New, $80
Jegs CO2 Regulator#60200, New, $65
Jegs CO2 Shifter for B&M Pro Bandit #62350, New, $105
Jerry Bickel Chrome CO2 Bottle Mount #JBRC1105, used, $50
B&M Shifter Cable Extension #80323, New, $45
B&M Shifter Cable Bracket #70460, New, #70460, $11

PayPal (+3%) & USPS Money Orders accepted

email: mgray0918@verizon.net or pm me thru Moparts

Thanks,
Mike Gray


Attachments
CO2 Bottle #2.JPG

B&M Shifter Acc..JPG


_________________________
RIP Monte Smith

aka: OutlawFish
'98 Bickel Dodge Dakota PST

Top
#2430836 - 01/07/18 09:14 PM Re: 340 rotating assembly [Re: moparts]
Dadodgekid Offline
member

Registered: 03/26/07
Posts: 55
Loc: Palm City, FL
Rotating assembly out of my Engine-

4.070 TRW domed pistons- L2232F I believe

Factory 340 Rods, Polished Beams and SPS bolts

Factory Forged 340 Crank. Balanced assembly .010ROds/ 010 mains

This has about 2000mi maybe and 20 blasts on the quarter sifting at 7800rpm.

will post pictures tomorrow

$1000 plus shipping


Edited by Dadodgekid (01/07/18 09:14 PM)

Top
#2431011 - 01/08/18 10:08 AM titanium retainers [Re: GTX5877]
an8sec70cuda Offline
I Live Here

Registered: 01/19/03
Posts: 10303
Loc: Marion, South Carolina [><]
Titanium valvespring retainers, set of 16. Very little use.
For 1.550" springs and 10° locks, Overall OD is 1.500", small step is .720", large step is 1.120"
$100 FIRM shipped in the lower 48, paypal accepted if you cover the fee
PM me here or call/text 843-431-8376


Attachments
retainers 1.jpeg


_________________________
CHIP
'70 hemicuda...8.91 at 150.5 mph street car...Mopar Action feature Dec. '14
'69 road runner 446" w/ Indy SRs
'69 road runner 440-6, 4 speed...Dad's ride
'71 Demon 340 resto project
'01 Ram 2500 QCSB 4x4 Cummins...toy hauler
'16 Grand Caravan SXT...baby hauler

Top
#2431336 - 01/08/18 08:07 PM Re: titanium retainers [Re: an8sec70cuda]
daytona5812 Offline
enthusiast

Registered: 11/10/04
Posts: 264
Loc: Mn.
Cleaning out garage.. Callies 8 bolt 4.50 crank. Stock mopar rods & mains, $1200 ex shape. C/P Pistons, 4.507 bore, 5 Dyno pulls only, ex shape, $950. 80 amp 1wire East Coast alt, $200. Three, 3 bolt roller cams, Lunati pt# 40239909 $200. Cam Motion pt# R2865-3001-12.5, $175. Huge Predator cam & springs, pt# R-1759-1783-15-2A, $500. Digital Delay two stage timer, works fine, $100. #1 4 digit delay box, works fine, $75. If you txt me I can send pics of parts & cam cards.. More parts to come... Thanks, Vern 218-391-9696. All parts are obo..


Edited by daytona5812 (01/08/18 08:13 PM)

Top
#2431749 - 01/09/18 04:06 PM Re: For Sale - Race Parts - 1st Quarter [Re: moparts]
brownout Offline
enthusiast

Registered: 12/20/11
Posts: 264
Loc: ca
Autometer gauges-

Water temp gauge new in box pt # 4437 -$50 shipped

Oil pressure gauge and sending unit used pt# 4427 -$60 shipped

Tach sport comp silver with shift light- $110 shipped

Buy all 3 for $200 shipped

call or text Cody at (916) 494-8888

Top
#2431751 - 01/09/18 04:07 PM Re: For Sale - Race Parts - 1st Quarter [Re: moparts]
brownout Offline
enthusiast

Registered: 12/20/11
Posts: 264
Loc: ca
Southwest Speed floor mount dual master cylinder setup with pedal in good used condition. One Southwest Speed master cylinder and one Wilwood master cylinder. Check part # 301-2582

$100 shipped

call or text Cody at (916) 494-8888

Top
#2431780 - 01/09/18 05:10 PM Re: For Sale - Race Parts - 1st Quarter [Re: brownout]
Jeremiah Offline
master

Registered: 03/03/03
Posts: 8084
Loc: Rogue River, OR
1425CFM Gen3 Holley Dominator - Like New -

Please see this link for details on Holley's site:

Holley 80911HB Dominator

I am also including a phenolic spacer with h/w,an AED throttle cable bracket/return spring combo (anodized red), AN -8 fuel lines and an aluminum carb hat.


SOLD





Attachments
20180109_123738_resized.jpg

20180109_123752_resized.jpg

20180109_123853_resized.jpg



Top
#2431938 - 01/09/18 08:46 PM Re: Indy 622" [Re: AlexBosak]
Azzkikrcuda Offline
top fuel

Registered: 01/20/03
Posts: 1610
Loc: North Dakota
Used Smith Brothers 5/16 diameter .083 wall pushrods, ball and ball ends 9.390 length. Pushrods look new, was setup for 440 solid cam and Comp Pro Magnum rockers. Were $170 new, $100+shipped

Clevite V-series bearings MS-1795V Std. size, 440 small thrust flange. Mocked up but not ran. $50 shipped

PM me here if interested.


Attachments
pushrods 001.JPG

bearings-six pack 002.JPG


_________________________
The only Carbs I care about are under the hood!

Top
#2431941 - 01/09/18 08:51 PM Ported Indy RB Dominator Intake W/ NOS Fogger, Jets $1000 [Re: AlexBosak]
Jeremiah Offline
master

Registered: 03/03/03
Posts: 8084
Loc: Rogue River, OR
For sale, one ported RB (tall deck aka 440) Indy intake. It has been ported and the plenum dividers have been extended. There is some welding around the ports where they meet the flange to add material when the ports were opened up.

This intake has been plumbed with an NOS fogger which includes two sets of solenoids (2 fuel, 2 n20), stainless lines, fogger nozzles and the hose and distribution blocks to tie both sides of the system together. All solenoids have Weather Pack connectors installed. This is an older setup but it is clean and well cared for.

1000 OBO with jets and instructions for the NOS kit.

PM me with you email address and zip code for pictures and shipping costs.

Thanks for the ad Moparts!


Attachments
20180109_124342_resized.jpg

20180109_124325_resized.jpg

20180109_124406_resized.jpg



Top
#2432622 - 01/10/18 11:19 PM Re: For Sale - Race Parts - 1st Quarter [Re: moparts]
pittsburghracer Online   content
Slowride

Registered: 02/02/05
Posts: 12294
Loc: PA.
JW powerglide to big block Mopar bellhousing
$300
Freeport, PA
I bought this a couple of years ago and only used it to mock up the engine and transmission in my Duster So I could have headers made. This is used to mate up a powerglide to your big block Mopar. New cost is 472.00 from Summit. Buy this one for 300.00 plus shipping from Freeport, Pa. 16229 PM or jacadamore@gmail.com



SOLD____SOLD______SOLD_____________SOLD_________SOLD_________SOLD





Untitled by John Cadamore, on Flickr


Untitled by John Cadamore, on Flickr


Untitled by John Cadamore, on Flickr


Edited by pittsburghracer (02/13/18 09:59 AM)
_________________________
1970 Duster
Edelbrock headed 408
6.143@110.89 mph
9.73@135.05 mph shifting at 6700 RPM
422 Indy headed small block
6.001@113.27mph
9.44@138.23

Untitled by John Cadamore, on Flickr





Top
#2432656 - 01/11/18 12:28 AM Re: For Sale - Race Parts - 1st Quarter [Re: pittsburghracer]
WHITEDART Offline
top fuel

Registered: 10/06/11
Posts: 2154
Loc: bean town
Good used 3 vane Moroso vacuum pump with fittings and mount that will bolt to a small block water pump.. this pump pulled 14in on my 408.. over $600 invested... yours for $350 plus the ride.. PM me here... Sold thanks Moparts


Attachments
20180110_211647.jpg

20180110_211654.jpg

20180110_211640.jpg




Edited by WHITEDART (01/15/18 08:15 PM)
_________________________
In the 8s N/A.with Brett miller W8
5.42 1/8

Top
Page 3 of 9 < 1 2 3 4 5 6 7 8 9 >

Advertisement
Sponsored Link
Forum Stats
25,151 Registered Members
32 Forums
186,847 Topics
2,174,309 Posts

Most users ever online: 882 @ 03/05/17 10:15 PM
Moparts Newest Topics
So I Dislike The 2019 Rams SO Much...
by Sunroofcuda
9 minutes 9 seconds ago
Question on the Caltracs
by David Lee
9 minutes 49 seconds ago
4speed fork boot installation
by hemi68charger
14 minutes 40 seconds ago
Plymouth Arrow Pickup
by 65pacecar
Today at 09:23 PM