Topic Options
#2426537 - 12/31/17 03:06 PM For Sale - Race Cars - 1st Quarter
moparts Offline


Registered: 01/19/03
Posts: 13854
Loc: Norwich CT USA
up

Top
#2426969 - 01/01/18 05:24 AM 91 Dodge Daytona [Re: moparts]
SCDaytona Offline
mopar

Registered: 12/03/06
Posts: 460
Loc: New Milford, CT
91 Dodge Daytona - VFN body- Chrome Moly cage- Certifed to 7.50 4 Link- 9" rear with 40 spline gun drilled axles with ceramic bearings and coated gears and bearings. Strange Strut front end with coated bearings at hubs. Car is presently set up for small block although I do have the plates for a big block. Car can be set up with most trans. such as glide, Profilte, 904 or 727. Has Biondo Mega 400 delay box, MSD DIgital 7 Ignition, Auto Meter Tach and gauges- Magnafuel 500 pump and aluminim fuel cell. Presently has a single 16 volt batttery and has mounts for dual battery. Car has run 8.15 on C16 and with Q16 (+30HP) ran 173 mph on a bad launch pass. Never sorted out on Q16. Has Penske Nitrogen shocks bult by Chris Bell. Can can be bought as a roller for $22k 383 Small BLock W8 CFE Heads sheet metal intake and Davince dominators- King Lightened crank, carrillo rods- Moroso oil and vacumm pumps and more $14K Profilte trans. w/ 2.23 1st gear air shifter and shields $5500. Weighs 1960 lbs less driver Car complete $38k Call 860-354-6701
[img:center]PICT4451WEB by Joseph Olejniczak, on Flickr[/img]
[img:center]http://Engweb by Joseph Olejniczak, on Flickr[/img]


Edited by SCDaytona (01/01/18 05:48 AM)

Top
#2427365 - 01/01/18 05:14 PM Re: For Sale - Race Cars - 1st Quarter [Re: moparts]
Highwaystar2 Offline
member

Registered: 02/17/10
Posts: 44
Loc: S. Central PA
1969 RoadRunner A-12 clone.
This is a turnkey car. Last run was this Fall. Runs a 6.50 1/8 10.30 1/4 mile.
Has more potential with more tune-up and airbox.
stock stroke 440 ci. filled motor with Indy SR Heads, Eagle rods, Ross pistons,Crane roller 1.6 rockers, M1 intake, Thumper 1050 carb. Low maintenance race motor.
New rebuilt 727 HRT transmission with aluminium drums, turbo action reverse valve body, and J converter.4 Link with new coilover shocks, Mark williams 9" ford, 35 spline axles, 4.56 strange center section.4 wheel wildwood disc brakes, 12 point cage, good to 8.50. Glass doors, fenders, hood, trunk, bumpers. All Lexan glass, except for windshield.
Car weighs 2850 with full tank of gas, fits comfortably up to 6'3".

New slicks, New MSD starter, New Transmission, New shocks, New 1050 carb and air cleaner, New 5 pt. Harness, New M/T slicks.

30K turnkey ready for next season, or trade for street or street/strip Abody/Bbody.



Car can be available with or without vinyl stickers.
T.J. Smith
S.C. Pennsylvania
call or text 717-512-7882
Highwaystar2@ymail.com


Attachments
DSC06513.JPG

DSC06503.JPG

20171104_174740.jpg

IMG_0574.JPG




Edited by Highwaystar2 (Yesterday at 12:11 AM)

Top
#2428200 - 01/03/18 08:01 AM Re: For Sale - Race Cars - 1st Quarter [Re: moparts]
RapidusMaximus Offline
top fuel

Registered: 06/04/03
Posts: 1834
Loc: Haslet, Texas
***PRICE DROP*** 17,000 OBO, Still looking for a 67-69 Dart...trades? 1994 SWB Dakota, fresh 5.2 Magnum stroked with a 4" Scat crank (388 CI), Eagle rods, block partial filled, billet main caps, ARP fasteners throughout, Edelbrock heads mildly ported, JE pistons, Total Seal SS rings, approx 9.4 CR, Custom hydraulic roller turbo cam by PIE, MSD crank trigger ignition, 76mm turbo, .96 AR, 3" piping on hot and cold side, 3" down pipe with Magna flow muffler routed out to the stock location, air to air intercooler, Hypercontrol boost management system, ECU is a Classic FAST fuel injection system, Aeromotive 1000 fuel pump, 12 gallon fuel cell, braided lines, tablet with all tuning data included. SRT8 seats, chrome moly 8 point cage integrated into the interior and routed cleanly through the stock dash. SRT8 seats, new carpet, door panels, sliding rear glass and windshield. Moser 60, 3.54 gear, QA 1 coilover shocks on the front, AFCO's on the ladder bar equipped rear. Billet Specialties Wheels, 315/60/15 tires with less than 500 street miles and a 6 no prep passes. Trans is a 727 with a Turbo Action reverse pattern manual valve body, trans brake, PTC 9.5 in converter, and a CRT deep pan and pickup.This truck is a race car with a truck body, it is street driven on pump gas but prefers a 50/50 mix of race gas for serious stuff, it is very quiet and mild mannered with disc brakes on all for corners (stock up from, Wilwoods on rear).
I am probably forgetting stuff but you get the idea, this is a professionally built and assembled street driven truck that has run 9's in it's past and the tune is the same now as it was then, only difference is the engine is fresh. Only reason for selling is I am looking for a 67-69 Dart to fit a particular "street" class that they won't let me into with this truck, with that being said, the ONLY thing i am interested in partial trading for is a 67-69 Dart that is already mini tubbed or is a good candidate for mini-tubbing and cal-tracking. I prefer a pm or email with a phone number for serious buyers to discuss details and additional picture requests, I am asking 18,500 or best close offer and like I said above am seriously interested in a 67-69 Dart partial trade. PM me here or email alilblacktruckatgmaildotcom, thanks


Attachments
New Dakota Drivers Side Pic.jpg

New Dakota Front Pic.jpg

New Dakota Pass Side Pic.jpg

New Dakota Eng Pic.jpg




Edited by RapidusMaximus (02/21/18 05:50 AM)
_________________________
1968 Plymouth GTX 440 4 Speed Dana
1973 Small block Duster under construction
1974 Dodge P/U Long Bed Stepside 318 Auto
1975 Jeep CJ5
2016 Dodge Ram Hemi 1500

Top
#2434007 - 01/13/18 03:27 PM Re: For Sale - Race Cars - 1st Quarter [Re: RapidusMaximus]
joez Offline
mopar

Registered: 01/19/03
Posts: 472
Loc: PA
1972 Dodge Challenger race car roller. SFI 25.5 mild steel chassis with stock front and rear frame rails. Fiberglass front end and deck lid. Has factory 1970 grill, headlights and tail lights for street appearance. Steel doors with working glass. Cowl hood with carbon pro stock style scoop.
Custom tubular k-member with flaming river mustang II rack and spindles. AVO double adjustable front coilovers, Qa1 adjustable rear coil overs, S&W ladder bars, diagonal link and splined anti roll. Chassis engineering wheelie bars. Wilwood disc brakes front and rear. Dana 60 with moser 35 spline spool and axles. Dewco pro-fin 3.73 pro gear. 15x11 holeshot rear wheels, Weld magnum front wheels.
Motor plate for BB Mopar. 2 3/8” custom headers with collector mufflers. ATI powerglide adapter midplate, flywheel.
Fiberglass stock appearing dash with autometer gauges, Stock door panels, Kirkey seat, firefox fire system, stroud chute, jaz 3 gallon fuel cell, dual nitrous bottle mount, laptop mount, quarter stick shifter MSD digital 7 programmable, hvc2 coil, strange low mounted master cylinder, afco radiator,
Last run with 528 B1MC low deck nitrous. Best ¼ mile 1.308/5.34@135.88mph/8.21@171.29mph. Best 1/8 mile 1.19/5.29@132.7mph @ 3,050lb Joe – nitrojoez@yahoo.com – 570-436-5544 $15,000 obo


Attachments
challenger.jpg



Top
#2434956 - 01/15/18 10:12 AM 1968 Plymouth Riad Runner S/SST [Re: joez]
Morris'Mopars Offline
enthusiast

Registered: 12/08/04
Posts: 377
Loc: Illinois
Selling this nice 1968 Plymouth Road Runner race car. It is a all out drag car not street legal but does have a clear title. The car is in over all nice condition. It has fiberglass hood with 6 pack scoop. Fiberglass fenders with headlight buckets and fiberglass front bumper. The doors, trunk lid and rear bumper are also fiberglass. All windows are lexan and could stand to be replaced. Full roll cage front to back. Rear end is a Strange Dana with 35 spline Spool, Billet caps, 4.56 pro gear, Ladder bars and QA1 coil overs with strange disc brakes. Up front also has QA1 coil overs, Strange Brakes and Flaming River rack and pinion steering. Set up for big block mopar and a power glide trans. It has a motor and mid plate.
Inside is all business with electric shifter, MSD 7al, Timing retardbox,3 step box, and digital delay box. The car also has throttle stop installed and ready to use. Building a new car so this one needs to go. Selling this car for $14000 rolling chassis. No engine or transmission but will include radiator, mid and engine motor plates and 2 drive shafts. It would take a long time to list all the good quality parts in this car. This car has been on the NHRA circuit running Super Street on throttle stop. Call today to set up a appointment to view the car. Sorry but no trades. Thanks for looking have a great day!!


Attachments
IMG_3350.jpg

IMG_3353.jpg


_________________________
www.morrismopars.com

Top
#2442260 - 01/28/18 12:18 PM 86 Dodge Daytona [Re: Morris'Mopars]
SCDaytona Offline
mopar

Registered: 12/03/06
Posts: 460
Loc: New Milford, CT
86 Dodge Daytona Full MS Chassis certified to 8.50, 4 link, Strange strut front end. Dana 60 with 4.56 gears. Strange rear shocks, parachute, Power Glide with Hurst 1/4 stick Shifter. Eastcoast alternator, Barry Grant pump with Magnafuel regualator. JFZ brakes all aorund and strange Master Cylinder. Davis Ultra dealy box. Msd 7AL2 ignition. Kirkey aluminum seat. Stroud belts. 394- W2 stroker motor wth Indy intake set up and carb. done by Shady Dell, Molnar crank, Cariilo rods and CP pistons. Charlies oil pan. Taylor blanket. Ran 8.76 @154 best so far. Has 14.5 x33 Hossier tires but can go to 17x33's. Asking $25K complete. WIll sell rolling as well. Call 203-648-1361 evenings or weekends
[img:center]033 by Joseph Olejniczak, on Flickr[/img] [img:center]032 by Joseph Olejniczak, on Flickr[/img]


Edited by SCDaytona (01/28/18 07:02 PM)

Top
#2445085 - 02/02/18 05:22 AM Re: For Sale - Race Cars - 1st Quarter [Re: moparts]
Jimi_Vignogna Offline
mopar

Registered: 07/21/05
Posts: 420
Loc: wappinger falls new york
http://i32.photobucket.com/albums/d25/ja...zpsxqzroir1.jpg

1997 S/S DODGE AVENGER ,GT,MODIFIED , X CLASSES, SUPER CLASSES, INDEX CLASSES ,PRO STREET CAR.

$26,000 complete car, will separate. Trades considered.

You will not find a better built or better quality component car anywhere. The price is a steal “MOTIVATED” just want it gone!!!!

ENGINE , 300” W8-R3
The engine is 300ci. W8 R3. It has cfe heads and intake. Holly 700 cfm dual carbs. 2.200”titanium intake 1.55” exhaust 380 cfm @26” water on super flow 600 flow bench. Flow clean to .850” lift T&d rocker gear. 1.65 ratio. Bullet cam ,.850”. Winberg billet 2.900” stroke crank X 4.080” bore. Block can go to 4.175” bore block is Siamese bore. 8.900” deck ht. 50 mm roller cam bearings. Groden Rods JE pistons 15.1 to 1. Weber belt drive. Ft mount distributor. Ati balancer with trigger built in Stock car products belt drive oil pump. Charles pan. Stainless step tube tri y headers. Moroso sheetmetal valve covers.
Engine is out and apart for parts verification and viewing.

TRANSMISSION,
A-1 proflite 2.39-1.5-1.0 clean neutral 7” negative blade tc ,trans is fresh.

REAR DIFFERENTIAL,
chromoly sheetmetal ford 9" rear , strange 40 spline gun drilled 300m axles.

BRAKES,
wilwood dual rear caliper brake set up,wilwood front disc brakes,all stainless steel hard lines. chrysler big bore aluminum master cylinder, custom ratio aluminum brake pedal, dot 5 synthetic fluid.
SUSPENSION,

santhuff front struts, rear coil overs, both double adjustable, Chris Alston avenger 4 link, splined anti roll bar, wish bone locater, lower dodge viper front controll arms.
CHASSIS ,

Alston/Half Scale chromoly chassis, built like a tube car in a stock uncut
body, car is certified to 8.50 , would need minor updates to exceed the 8.50 spec.(front gussets,funny car cage addition)car is fitted to accept large driver, 6' 300#, has driver side swing out bar.

INTERIOR,
full stock interior, two seats , full carpet, stock dash board, dash removes in 5 minutes, both power windows operate, all stock glass no lexan.
BODY,

complete stock body except for fiberglass hood. beautiful all black paint, has small dent above driver door. stock location fire wall, stock location factory front frame rails and fender wells, this engine bay has a ton of room for any engine.

RIMS /TIRES
weld wheels , hoosier tires, no tubes.

CONTACT,
James Vignogna 845-298-9041 jarn05@msn.com photobucket


Edited by Jimi_Vignogna (02/02/18 05:27 AM)

Top
#2445450 - 02/02/18 10:25 PM 1973 Duster & 28 ft Enclosed Trailer [Re: moparts]
steeldust Offline
mopar

Registered: 06/05/10
Posts: 464
Loc: Tennessee
1973 Duster with a 582 ci world Aluminum RB block 440-1 heads ported 15 to 1 with NOS fogger 727 race trans with brake Dana 60 with 374 gears wilwood dic brakes front and rear tubular front end cage is certified on 275 Drag Radials car & Driver last year # 2,910 lbs now 2,810 lbs just car # 2,610 lbs I run in LDR last year 5.16 et @ 134 mph 60 ft 118 1/8 mile small tune it will be faster this year. More go`s with car . 2014 Like new 28 ft enclosed trailer with winch tool box 5 10 lbs nitrous bottles full 3 co2 bottles full 55 gallons race fuel to much to list . The car could be put back on the street with work I have good title fender tag vin on dash $32,000 or Partial trade on a MOPAR street car .931-303-6825 or email jkeyes440@gmail.com Thanks for looking GOD Bless.


Attachments
7.jpg




Edited by steeldust (02/19/18 10:31 AM)

Top
#2448536 - 02/08/18 12:14 PM Re: For Sale - Race Cars - 1st Quarter [Re: moparts]
als499 Offline
mopar

Registered: 08/29/03
Posts: 673
Loc: Zumbrota,MN
1 Winston Cup and 1 Busch Cup car, rough condition both rolling ,no drivetrains, parked outdoors 20+ years, maybe they could be re-skinned with Mopar bodies ? $3,500. each 507-732-4363 Zumbrota MN Thanks !


Attachments
rusty111.jpg

busch tbird.jpg


_________________________
www.alsrapidtransit.com

Top
#2448598 - 02/08/18 02:09 PM Re: For Sale - Race Cars - 1st Quarter [Re: moparts]
++MAX WEDGE++ Offline
member

Registered: 04/21/08
Posts: 87
Loc: Near Columbus, Ohio

71 Plymouth duster. Org a 340, auto car. Now has built 440, auto. Please see photos. Car was org a purple car with console. Very solid. Can be converted back to street. Has been mini tubed. New Eng., trans and rear end ( 8 3/4) turn key ready. 15K obo. Have clear title in my name. Could need paint on car if you would want it nice. Any ? please PM me. Thanks.

up




Attachments
20170830_125356.jpg

20170830_125609.jpg

DSC03320.JPG

20170830_125030.jpg




Edited by ++MAX WEDGE++ (02/08/18 02:18 PM)

Top
#2449732 - 02/10/18 05:20 PM Re: For Sale - Race Cars - 1st Quarter [Re: kdtjb]
tonys68dart Offline
member

Registered: 04/19/06
Posts: 66
Loc: oroville, ca
1970 Cuda, runs 9.50's@143. Very consistent.470 CID, 590 purple cam,harland sharp rockers,bulldog heads,Ron's injection (terminator),MSD digital 7,crank trigger, Milodon gear drive, Rock 16 volt,Biondo 450, PPI air shifter,FAST 02,computech EGT,GZ vacuum pump,on board fire suppression,Dana 60, 4.56,ladder bars,4 wheel disc brakes.Much more info if interested. Car is located in Northern California. 50k.
Tony
5305211651 or pm me here thanks


Attachments
2D0BD99B-AC01-40FB-8E96-9D50332EA404.JPG

F18E632D-0FEE-414A-A31D-18B1B240A4DD.JPG




Edited by tonys68dart (02/12/18 01:31 AM)
Edit Reason: parts

Top
#2450095 - 02/11/18 12:01 PM 68 Dodge Dart [Re: tonys68dart]
sixpacksteve Offline
super stock

Registered: 01/18/04
Posts: 1159
Loc: n.y.
68 block, 505" stroker
4.25 scat crank n H beam rods
12.5 flat top pistons
external oiling milodon pan
682 Bullet cam
Edelbrock victor max heads
T&D roller setup
indy max intake
1150 holley
MSD ignition system
hedman hustler headers
Coan full race trans w/transbrake
Ultimate 8" 5500 convertor
custom strange driveshaft
Dana 60 rear 4:10
M/T slicks 29.5x10.5
Cage NOT certified
seat belts are 6/17
can make streetable w/exhaust
has glass fenders and hood
has super stock seats and aluminum brackets by Gary Ball
has steel bumpers,brackets rear seat etc..
Engine has just been rebuilt Only 9 Passes
Trans has just been been Rebuilt Only 4 Passes

Cars best so far 9.70 at 138 mph
60 ft. 1.39
asking 23.5K i have at least that much just in receipts


Attachments
PC030087.JPG

PC030090.JPG

PA280755.JPG




Edited by sixpacksteve (02/11/18 12:04 PM)

Top
#2455292 - 02/21/18 06:41 PM Re: 68 Dodge Dart [Re: sixpacksteve]
Dragula Offline


Registered: 05/02/04
Posts: 10113
Loc: Taxes R-US, NY
I have two 9 second pump gas cars, and do not need both, so I putting my pump gas Duster up for sale.

https://www.youtube.com/watch?v=Z_XTmRBuvWs

Its a 72ish Duster with a lot of good parts on it, that is very easy to work on. I have owned it five years and raced it for six years. Every year the engine gets freshened and all new bearings and rings with a thorough inspection and anything else it needs replaced. This past winter, it had all the rings and bearings replaced as well as the timing chain and all the gaskets.

The car is a back half big tire four link coil over car with an S&W rear sway bar. Rear tires are 17x33 slicks and a narrowed Dana 60 with 4.56 gears. The dana has a bearing preload style cover on it as well. Tires have a full season on them, and still have tread.

Car has a full cage, and is currently certed to 8.50. It has a full halo, and front bars, knee bar and window net, one seat and the typical 5-way harness an aluminum dash with the typical gauges in it. Interior also has aluminum door panels and sail panels and the window cranks were left intact and are very functional.

Trunk area has the typical back half treatment with aluminum tubs and trunk floor with fuel cell. 275 Magna fuel pump is mounted underneath. 1/2 line up to the carb and -10 to the pump and return line.

Front of the chassis is Magnum force with DA coil overs and no inner fenders. The shock towers are tied right into the front bars and everything is super easy to work on.

Body is in fair to good condition. Paint is six years old, and is about a five footer. Has a dent where the hood flew off on the top drivers fender. Not perfect, but not that bad either. Hood is brand new as well as the lexan front and rear windows. Side windows are still glass with working cranks.

Engine is new with four passes on it. 440Source 512 w/light weight crank option based 400 low deck with 10.8:1 and Indy EZ1 heads. Ran 9.70 with a 440/512 and is on pump gas with a Thumper Carb 4500 1050cfm carb.

Trans is a built 727 billet A&A drum with a carbon fiber CSR shield, A&A sprag, TransAct of Indy Trans brake full manual revers valve body. 8" convertor with a 5K stall. Car can be foot braked or launched off the two step and trans brake.

$26k for the car ready to race. Contact me here or thru e-mail for faster response. If your goal is to buy it as a roller, a 10% deposit on the $18k roller price is required before I pull anything apart.


Attachments
DSC00360_zpsoab7twyo.jpg


_________________________
'71 Duster Pump Gas 512LD for sale now too
https://www.youtube.com/watch?v=Z_XTmRBuvWs (6.19)
https://www.youtube.com/watch?v=gQZGfDBPROM (9.70 at 138.5mph)

'70 Cuda, 3rd year straight, can't enjoy it...Needs an engine or needs to go.
https://www.youtube.com/watch?v=WYw6RA-k5Bk (6.31)
https://www.youtube.com/watch?v=JCvfzsC4NgM (9.9)

Top

Advertisement
Sponsored Link
Forum Stats
25,149 Registered Members
32 Forums
186,810 Topics
2,173,772 Posts

Most users ever online: 882 @ 03/05/17 10:15 PM
Moparts Newest Topics
Needed: a BIGGER gun!
by amxautox
02/24/18 03:24 AM
Adjustable shocks?
by 451Mopar
02/24/18 02:35 AM
Smoking left bank
by Dave Hall
02/24/18 01:12 AM
440 install with spool mounts
by 340clone
02/24/18 12:53 AM