Page 8 of 12 < 1 2 6 7 8 9 10 11 12 >
Topic Options
#2402795 - 11/12/17 08:36 PM Hoosier Slicks [Re: moparts]
cb1289 Online   content
member

Registered: 09/01/07
Posts: 112
Loc: NJ
2 Fresh 30x9-15 Hoosier Bias Ply Drag Slicks. D07 compound. Purchased in September 2017, tested once at the track. Exactly 5 Quarter Mile Passes. Excellent condition

$300 plus shipping or local pickup in Dumont NJ 07628.

PM me on Moparts, Thanks


Attachments
edited.jpg

IMAG0999.jpg

IMAG0985.jpg


_________________________
62 Dodge Dart Wagon 65 Plymouth Satellite

Top
#2403097 - 11/13/17 01:40 PM Alum Crossflow Radiator [Re: moparts]
jcc Offline
No politics

Registered: 12/21/03
Posts: 16815
Loc: Trumussia
Used in good working condition Alum Crossflow Radiator, has dull typical weather finish, never been on the street, don't remember who built it, guessing Griffin. Was intended for SB B body, 1.5" Inlet Drivers Side, 1.75" Outlet Pass, Side, no other connections, has two gusseted lower undrilled support brackets, as is, $110 + shipping/packing, payment within 7 days, ships from SW Fla PM

Overall 31" W x 19 3/16" H 2.25" deep
Core 27.5" W x 18.25" H
Brackets approx 6.75" above bottom
Core tubes 2 x 1"





Attachments
Alum rad 1.jpg

Alum rad 2.jpg



Top
#2403153 - 11/13/17 03:43 PM SB TR w/carbs/filter [Re: jcc]
jcc Offline
No politics

Registered: 12/21/03
Posts: 16815
Loc: Trumussia
Sold, Thank you


Edited by jcc (12/22/17 01:05 PM)

Top
#2403166 - 11/13/17 04:08 PM Dana 60 Spool [Re: jcc]
jcc Offline
No politics

Registered: 12/21/03
Posts: 16815
Loc: Trumussia
Dana 60 Spool not sure if it ever has been used, will check spline count, as is, as pictured, $90 + shipping/packing from SW Fla, payment within 7 days PM

I have been asked what series/ratios this will accept, I don't know, is there a measurement I can take to answer this question?


Attachments
dana spool 1.jpg

dana spool  2.jpg




Edited by jcc (11/17/17 03:52 PM)

Top
#2403169 - 11/13/17 04:13 PM PAC 1226 Springs [Re: jcc]
jcc Offline
No politics

Registered: 12/21/03
Posts: 16815
Loc: Trumussia
New in Box PAC 1226 Valve springs, as is, as pictured, $240 + shipping/packing from SW Fla payment within 7 days PM


Attachments
Pac Springs 1.jpg

Pac 1226 Springs 2.jpg



Top
#2403841 - 11/15/17 12:11 AM Re: For Sale - Race Parts - 4th Quarter [Re: moparts]
bc9711 Offline
member

Registered: 10/25/17
Posts: 1
Loc: illinois
Mopar megablock for sale pn2468330-m
4.505 bore program main caps, lifter bores bushed and indexed, 0-ring decked ,billet main seal cap, Siamese block 2800 obo

Top
#2403896 - 11/15/17 08:24 AM Re: For Sale - Race Parts - 4th Quarter [Re: moparts]
301v Offline
member

Registered: 09/06/17
Posts: 13
Loc: Kentucky
GRP 5300 pro series rods for sale.This is the upgraded beefier rod over the 5100 series.
NEW in the box still.. Never used
.990 pin.. 2.200 main with chevy width. 6.760 length.

Cost $1250 new.. Will take $850 plus the ride or trade for something i can use.

I can text pics or email them to you.

sc301v@yahoo.com


Attachments
20171115_134836[1].jpg




Edited by 301v (11/15/17 03:25 PM)

Top
#2404160 - 11/15/17 05:09 PM Cuda fibergalss fenders (E body) [Re: moparts]
6PACKB Offline
member

Registered: 03/28/16
Posts: 137
Loc: Waterford MI
Cuda fibergalss fenders.
I don't think these have ever been on a car. Look to be in good shape, only issues that I can see is it looks like someone was going to put side markers in them then filled the holes back in.

I think these will fit all five years of E body barracudas.

Asking $400 or trade, need lots of 70/71 Cuda stuff


Attachments
00x0x_IrIiPwfXXH_1200x900.jpg

00505_2YIk1zYGQgu_1200x900.jpg

00z0z_hd4Ltnjpk9l_1200x900.jpg



Top
#2404227 - 11/15/17 07:04 PM Re: For Sale - Race Parts - 4th Quarter [Re: moparts]
H4E2M6I Offline
super stock

Registered: 03/07/04
Posts: 957
Loc: Belvidere,IL N.W. Chicago ...
65 Dodge/Plymouth Acid dipped doors and left fender. $1000 for all or $800 doors only. Calls only if interested, no trades. 815-218-1733


Attachments
002.JPG

003.JPG




Edited by H4E2M6I (12/26/17 12:49 PM)

Top
#2404775 - 11/16/17 10:31 PM 230 Thick main 400 block [Re: moparts]
Newbomb_Turk Offline
member

Registered: 09/19/05
Posts: 159
Loc: Archbald, PA
I have for sale a 1971 400 230 casting thick main block. Casting date 7/71, Std bore, virgin motor. Has 1 broken bolt in water pump mount, not a big deal to fix. Will meet within reason or can pallet & drop off at truck freight shipper. $1200. OBO

Email is the best way to get me

newbombturk1@earthlink.net

Thanks, John


Attachments
400 block 1.jpg

400 block 3.jpg

400 block 5.jpg

400 block 7.jpg




Edited by Newbomb_Turk (11/19/17 02:41 PM)
_________________________
1971 Demon 440 auto Drag car full tub, Best 10.47 @ 126

Top
#2405103 - 11/17/17 03:09 PM Re: For Sale - Race Parts - 4th Quarter [Re: moparts]
Jet Doc Offline
enthusiast

Registered: 03/02/07
Posts: 215
Loc: Wisconsin
Mallory 140 Pump, regulator and filter.
Just removed these parts from my 62, they are in full working order. $200 shipped to the lower 48 states. Paypal accepted or money order.


Attachments
FullSizeRender (1).jpg




Edited by Jet Doc (11/30/17 05:29 PM)
Edit Reason: price drop

Top
#2405270 - 11/17/17 10:27 PM Re: For Sale - Race Parts - 4th Quarter [Re: moparts]
71yelladustr Offline
super stock

Registered: 12/25/10
Posts: 1019
Loc: Missouri U.S.A.
Slightly Used CNC ported 906 casting BB heads by KG engines. Have about 40 passes on them and are ready to bolt on. Ferrea 2.14/1.81 valves,bronze guides, Comp chromemoly retainers, locks and 928 springs. $1200 + shipping. PM or text (573)433-0192. Thanks.

Jason
_________________________
71 duster 452" 906 heads by KG, E-85 727 Dana 60

Top
#2405414 - 11/18/17 10:11 AM Re: For Sale - Race Parts - 4th Quarter [Re: moparts]
camastomcat Offline
top fuel

Registered: 04/12/05
Posts: 1994
Loc: Salt Lake City
Less than 1/2 of new price full set of KB dry sleeves, 4.630 OD, 4.320 ID in great condition $500

1/2" hemi pan pick up $35

Canton remote oil filter -12 fittings in and out $50

Spin on adapter for oil accumulator line and system one $55
JW Wheel Out of date $75
JW wheel and Ultrabell out of date, well used but usable $150
Diamond Predator pistons 4.485 .990 pins, with buttons, tool steel pins, and coated 142 passes $600
GRP aluminum rods 2.200-.990 142 passes $300
MSD custom HEI Plug wires straight plug ends 8.5mm for BBMopar $35
Meziere electric water pump $350 Sold
Dry Sump 3 gallon tank mounts $35
Crank trigger kit BB Mopar New $250 Sold
P/G Sheet metal pan $40
C02 bottle clamp $30
Mopar Offset Distributor $450 Sold
Summit upright fuel cell new SUM290110 $100
2 3/8 to 4 1/2 collectors w/tabs $50
In-line T/stop for rod style $50
Digital MSD ignition box 75301 early model Grid style with coil used for testing only, $500
Mopar Predator 1.9 T&D full set plus spare rockers dyno use only $900
Summit digital ignition for street car brand new SUM850610 $100 Sold
Mopar water neck for BBMopar with mount for fuel regulator $60
Canton remote oil filter $75
Vortex cone mufflers 4 ½ collector size $65
Manley valve springs brand new never used plus spares cost $630 at summit $500
All prices plus shipping
For more pics or questions Call Tom 801 949 7791


Attachments
Parts 1.jpg

Parts 3 (2).jpg

Parts 2 (2).jpg

Canton Filter.jpg




Edited by camastomcat (11/26/17 10:18 AM)

Top
#2405578 - 11/18/17 04:08 PM Re: For Sale - Race Parts - 4th Quarter [Re: moparts]
ssasdodge Offline
member

Registered: 03/19/05
Posts: 25
Loc: Pittsburgh PA.
W-7 & W-8 Parts,P-5 parts. I have 17 sets of New intake gaskets .045 to .060 thick $20.00 a pair. 1 set of New felpro Mopar W-7-8-9 head gasket .039 thick with a bore size of 4.250 $75.00 for the pair. 1 sets of used w-7 race pistons $200.00 , 4 sets of W-8 used race pistons $200.00 a set, used aluminum rods $200.00 a set, 50 MM used roller bearing Race Cam For R-3 small block $200.00.I have 1 pair of P-5 clam shell heads complete with titanium valves, Jesel roller rockers, Valve springs,Carbon Fibre Valve Covers, HRE Sheetmetal intake and 1 brand new extra P-5 head $2995.00. Also used Webber Belt drive for R-4 block $995.00. Call Wes Leopold @ 412-370-9371 cell or 412-563-6000 shop EST or email SSASDODGE@AOL.COM


Attachments
P-5 head.jpg

HRE INTAKE & Carbon Valve Covers.jpg

R-4 Belt drive.jpg

W-7-8 gaskets.jpg




Edited by ssasdodge (11/18/17 04:26 PM)

Top
#2406050 - 11/19/17 05:25 PM Re: For Sale - Race Parts - 4th Quarter [Re: ssasdodge]
SCDaytona Offline
mopar

Registered: 12/03/06
Posts: 459
Loc: New Milford, CT
Buxton 0-600 lbs on head spring tester. Best tester out there. Sold
LSM on head valve spring removal tool. Will work with W8 or W9 heads $150
Intercomp Scale system SW500 complete $800
Racepak V300Sd Datalink lite with the following: Ultra dash, oil pressure, oil temp, vacuum, water temp., fuel pressure,dual O2's, both rear shocks, 8 magnet collar, roll bar mount, all sensors and cables for the above. Also monitors G Force long. and Latitudal, voltage, rpm, able to see convertor slippage as well. I have the full documnetation as well as the dongle for install. This cost $5500 when I bought this, will sell for $4500.
Honda 3000IS Generator. Very quiet and reliable generator. $1400.
All prices plus shipping. Generator cannot be shipped and is in New Milford, CT
Call 860-354-6701 [img:center]IMG_0643 by Joseph Olejniczak, on Flickr[/img] [img:center]IMG_0637 by Joseph Olejniczak, on Flickr[/img] [img:center]IMG_0641 by Joseph Olejniczak, on Flickr[/img]




Edited by SCDaytona (12/07/17 09:19 PM)

Top
#2406619 - 11/20/17 10:08 PM Re: For Sale - Race Parts - 4th Quarter [Re: moparts]
H4E2M6I Offline
super stock

Registered: 03/07/04
Posts: 957
Loc: Belvidere,IL N.W. Chicago ...
Intake off of a 383 mag engine, Rare performance option manifold with Carter carbs. Manifold part # 1827899-1 maybe a date code of the time. This was not a factory installed manifold but was available as a dealer installed performance part or sold over the counter at a dealership only. $250 Serious calls only please. 815-218-1733


Attachments
001.JPG

004.JPG




Edited by H4E2M6I (12/26/17 12:47 PM)

Top
#2407344 - 11/22/17 10:30 AM Complete Alum 572***SOLD*** [Re: 493_john]
408strokerdart Offline
master

Registered: 02/03/03
Posts: 3445
Loc: Out West
Since I am building a Gen 3 for my '67 Dart and my new Top Sportsman car won't be done for a long time I have made the decision to sell my all aluminum 572. It has very low runs since freshened (I believe less than 40).

It can be purchased two different ways. Set up for Gas with a tunnel ram and two dominators or set up with a new (never had fuel thru it) single Rons terminator alky system. $15,500 set up for gas or $16,900 set up for Alky.

Indy Max block
Indy 345CNC heads
Callies Crank
GRP rods
JE Pistons (I think) 15:1 compression
Charlies chassis car pan
Milodon Pump
Indy pump cover
Jesel cam drive
Jesel Rockers
Jesel Front Drive Distributor
Comp Solid Roller
Spray bar valve covers
AR Engineering remote WP fittings
AR Engineering timing pointer
ATI balancer
MSD Crank Trigger
Superformance Gaskets
Firecore wires

This is a quality piece. Proven power and very reliable 970hp (on Gas). Probably closer to 1000hp (on Alky). I know this will move a 2650 lb car to 5.30 @ 130 1/8th mile times.

Pics are available. PM me an email address and I will send anything I can.


Edited by 408strokerdart (12/12/17 10:59 AM)
_________________________

Fuel Injected Gen 3 stroker coming Spring 2018

Top
#2407682 - 11/22/17 10:36 PM Re: For Sale - Race Parts - 4th Quarter [Re: moparts]
H4E2M6I Offline
super stock

Registered: 03/07/04
Posts: 957
Loc: Belvidere,IL N.W. Chicago ...
Two NOS 4500 1050 cfm Holley carbs, NEW OLD STOCK, $800 New K&N filters are $200.
Call only if serious. 815-218-1733


Attachments
002.JPG




Edited by H4E2M6I (12/26/17 12:44 PM)

Top
#2407942 - 11/23/17 02:54 PM Simpson Bandit Helmet size L worn 3 times [Re: moparts]
Swingin70 Offline
member

Registered: 06/20/17
Posts: 6
Loc: ca
Received as a gift I decided to sick with my open face. Nearly brand new snell 2015 rated. Retail for $449.00

Asking $325.00 shipped
PayPal accepted.

Thank you.



Attachments
IMG_2383.JPG

IMG_2384.jpg

IMG_2386.jpg

IMG_2387.jpg




Edited by Swingin70 (12/18/17 01:58 PM)

Top
#2408292 - 11/24/17 12:55 PM Re: For Sale - Race Parts - 4th Quarter [Re: SCDaytona]
boatracer572 Offline
super stock

Registered: 09/17/03
Posts: 957
Loc: San Jose Ca.
New indy block ALL machine work done and ready to assemble...all machine work done by Rick Santos@ S&S on rotler CNC block milling center,4.500 bore, wedge head pattern. honed with deck plates,all water jackets and oil passages have been pressure checked...CHE lifter bushings .904",O-rings in deck,55mm roller cam bearings (all 5),clearanced for belt drive..Line honed,Decks trued to cam and crank,Pushrod oil, std. cam height ........ $5700 over 2k in machine work alone...firm..... local pick up or can ship at new owners expense... Very nice piece, only selling because I bought a new trailer,I don't need to sell it, and will keep it if I don't get what I want
tony
408 316-0410


Attachments
image.jpg




Edited by boatracer572 (11/24/17 01:05 PM)

Top
Page 8 of 12 < 1 2 6 7 8 9 10 11 12 >

Advertisement
Sponsored Link
Forum Stats
25,077 Registered Members
32 Forums
185,669 Topics
2,158,527 Posts

Most users ever online: 882 @ 03/05/17 10:15 PM
Moparts Newest Topics
ID these steering boxes
by mickm
25 minutes 40 seconds ago
06 bed fender rust
by cudaman1969
Today at 06:20 PM
727 Adjuster screw leaking - O-ring seal fix?
by grancuda
Today at 05:43 PM
Grille - Known sources?
by oldjonny
Today at 05:40 PM