Page 4 of 8 < 1 2 3 4 5 6 7 8 >
Topic Options
#2345615 - 07/30/17 08:29 AM Big block tunnel ram [Re: moparts]
Dean1967 Offline
member

Registered: 06/04/17
Posts: 12
Loc: Michigan
I have a RB Mopar WEIAND Tunnel Ram with (2) 1850-2 600 CFM Holley carbs. This unit has been in my basement for years. I have included with this sale a couple Holley rebuild kits. I figure they should probably be freshened up after sitting so long.

The 2 Matched Holley 600 carbs were rebuilt and modified for Tunnel Ram use.
1. They were Vat cleaned
2. Blown out with 150 lbs of air pressure
3. Bead blasted to remove old finish
4. The bodies have been powder coated sunrise gold
5. The bowls, metering blocks have been polished
6. Reassembled with Holley non stick blue gasket set

Modifications include....
1. Vacuum secondaries have been replaced with Quick Fuel Adjustable's.
2. The stock 25 shooters have been replaced with 29's
3. The secondary metering plates have been enlarged .002
4. The pump cam location has been changed to the #1 setting.

These modifications have worked well for me in the past as a good starting point for any dual quad setup. Of course you'll still have to make some tuning adjustments to fine tune them for you motor to maximize performance.


$800 or best.
PM me or nitrousoxcide@hotmail.com


Attachments
IMG_0482.JPG

IMG_0814.JPG




Edited by Dean1967 (07/30/17 10:49 AM)

Top
#2345684 - 07/30/17 11:01 AM Alternator Bonanza Check Numbers and Dates Codes [Re: moparts]
blewbyu Offline
master

Registered: 01/22/03
Posts: 3204
Loc: Florida
These are all rebuildable cores, may be able to use as is but being sold as cores.

2098830 23-63 Non original rear Brg. $ 50.00

All these are # 2642537

Date 29 - 68 All Original rear Brg Never Apart $200.00
Date 4? - 68 Non Original rear Brg Hard to read date $125.00
Date 4? - 68 Non Original rear Brg Hard to read date $125.00
Date 2 - 69 Non Original rear Brg $175.00
Date 5 - 69 Non Original rear Brg $175.00

2875714 Date 31 - 68 Non original rear Brg. $100.00
2875714 Date 22 - 69 Non original rear Brg. $100.00

2875724 Date 5 - 69 Non original rear Brg. $195.00

3438171 Date 35 - 69 Non original rear Brg. $125.00

3438178 Date 1 - 70 All Original rear Brg Never Apart $200.00

Plus shipping from Florida

blewbyu2bad@aol.com

Top
#2345789 - 07/30/17 03:31 PM Big block valve covers [Re: moparts]
Im4dux Offline


Registered: 01/17/14
Posts: 20
Loc: Ohio
Great shape. They came off of my 70 bee (putting back to stock). Will fit 383 and 440's $85. Can ship or deliver to the mopar nationals.


Attachments
IMG_0591.JPG



Top
#2346171 - 07/31/17 10:50 AM Re: For Sale - Big Block Engine - 3rd Quarter [Re: moparts]
crabman173 Offline
master

Registered: 01/01/06
Posts: 3534
Loc: Big Lick , North Carolina
BIG BLOCK DOUBLE LOWER PULLEY For cars with power steering from 66-71 or so--these are reproduced at $60 a whack but here is a nice original just needs clean up--ex cond will also fit small blocks $35 shipped free Thanks dusterdave173@gmail.com


Attachments
addddd 021.JPG

Description: 7


_________________________
I have always had a fascination with fast cars at the expense of more normal character development

Top
#2346187 - 07/31/17 11:28 AM Engines, heads, H.P. Ex manifolds, intakes, etc [Re: Joesixpack]
GTX70sixpack Offline
top fuel

Registered: 03/05/06
Posts: 1611
Loc: Pataskala, Ohio
Clearing out anything that not earmarked for a project. 1966 440 complete oil pan to air cleaner, all accessories including A/C compressor, $550. 1970 383 H.P. out of a 70 Challenger R/T, pulled in 82 with 69k, no oil pan, $550. 915 heads, 906 heads, 440+6 cast iron intake w/carbs (new center carb), H.P. exhaust manifolds, valve covers. "Yard Sale Style" sale going on during Mopar Nationals weekend, near track and Reynoldsburg GTX70sixpack@insight.rr.com
_________________________
65 Belvedere II Station Wagon
69 Coronet R/T convertible
70 GTX
70'cuda
99 Dodge Diesel dually 4X4

Top
#2346405 - 07/31/17 08:26 PM Re: For Sale - Big Block Engine - 3rd Quarter [Re: moparts]
AndyF Offline
Too Many Posts

Registered: 01/20/03
Posts: 23020
Loc: Oregon
SOLD


Attachments
DSC_1010 (Large).JPG




Edited by AndyF (08/16/17 09:57 PM)

Top
#2346496 - 07/31/17 10:27 PM 1970 440 Sixpack distributor #2975982 [Re: AndyF]
Mopucky Offline
enthusiast

Registered: 03/18/13
Posts: 281
Loc: New York
Very early 1970 440 Sixpack distributor for an auto. Very good condition with a great original tag. $600 obo. Pm me if interested. Thanks.


Attachments
IMG_5583.JPG

IMG_5584.JPG

IMG_5585.JPG



Top
#2346840 - 08/01/17 05:19 PM Re: For Sale - Big Block Engine - 3rd Quarter [Re: moparts]
viperblue72 Offline
top fuel

Registered: 08/23/06
Posts: 1780
Loc: junction city oregon

Quick Fuel 3 circuit dominator 1050. Good condition. 400
Selling because I'm changing direction to a 4150 setup.
Located in Oregon
541-223-2836
Chad


Attachments
IMG_1807.JPG




Edited by viperblue72 (08/12/17 09:41 AM)

Top
#2347031 - 08/01/17 09:59 PM Re: For Sale - Big Block Engine - 3rd Quarter [Re: moparts]
68shifter Offline
super stock

Registered: 01/29/07
Posts: 1084
Loc: MI
Sold.
Thanks Moparts


Edited by 68shifter (08/03/17 10:09 PM)

Top
#2347116 - 08/02/17 12:46 AM Re: For Sale - Big Block Engine - 3rd Quarter [Re: moparts]
dsd70bee Offline
I Live Here

Registered: 08/24/03
Posts: 13246
Loc: oak park, il.
One pair of 1973 400 and 440HP exhaust manifolds in nice used condition RH casting #3751074 date code A153, LH casting #3751068, date code 12,21,72, both manifolds are in nice used condition $350.00 for the pair (708)288-2879 Scott


Attachments
parts 8-1-17 009.JPG

parts 8-1-17 008.JPG

parts 8-1-17 012.JPG



Top
#2347216 - 08/02/17 10:11 AM Re: For Sale - Big Block Engine - 3rd Quarter [Re: moparts]
dsd70bee Offline
I Live Here

Registered: 08/24/03
Posts: 13246
Loc: oak park, il.
1971 440HP 4-speed Carter AVS carb, date code G0, nice used original carb $300.00 (708)288-2879 Scott


Attachments
parts 8-1-17 014.JPG

parts 8-1-17 017.JPG

parts 8-1-17 015.JPG

parts 8-1-17 018.JPG



Top
#2347380 - 08/02/17 02:26 PM Hughes BB Mopar Victor Heads 1.7 Offset Intake Rockers [Re: dsd70bee]
BradH Offline
I Live Here

Registered: 01/30/03
Posts: 13210
Loc: Valhalla... eventually
*** SOLD ***


Attachments
Hughes Victor rockers.png




Edited by BradH (08/12/17 06:04 PM)
_________________________
Life's too short to waste time on dumb@ss internet pi$$in' contests...

Living by the motto “It’s just easier to keep buying parts than bother with actually putting them together” since 2010… or was it 2000?

Top
#2347524 - 08/02/17 08:25 PM Re: For Sale - Big Block Engine - 3rd Quarter [Re: moparts]
ChrgrCuda Offline
super stock

Registered: 08/24/08
Posts: 724
Loc: Texas, USA
Used 906 Cylinder Heads removed from 1972 440. $300 plus shipping. Call or text me at 972-921-1470


Attachments
440 Heads 1.JPG

440 Heads 2.JPG

440 Heads 3.JPG

440 Heads 4.JPG


_________________________
68 Cuda Notchback [Email]10.86@120[/Email] 69 Charger R/T 440/505 2009 Challenger SRT8

Top
#2347963 - 08/03/17 02:02 PM Re: For Sale - Big Block Engine - 3rd Quarter [Re: moparts]
Rockland71GTX Offline
member

Registered: 04/04/08
Posts: 64
Loc: West Palm Beach, Florida
FOR SALE! Offenhauser 360° manifold for
RB engines. Nice condition.
Asking $175 obo + shipping from 33467


Attachments
$_1.JPG



Top
#2347967 - 08/03/17 02:07 PM Re: For Sale - Big Block Engine - 3rd Quarter [Re: moparts]
Rockland71GTX Offline
member

Registered: 04/04/08
Posts: 64
Loc: West Palm Beach, Florida
SOLD! Thanks Moparts😁

FOR SALE! Edelbrock Performer 440 manifold for
RB engines. Very nice condition!
This is unusual in that it doesn't have the EGR pad machined into it.
Much cleaner look!
Asking $150 obo + shipping from 33467.


Attachments
$_1-1.JPG




Edited by Rockland71GTX (08/09/17 11:36 AM)

Top
#2348316 - 08/04/17 07:17 AM Re: For Sale - Big Block Engine - 3rd Quarter [Re: moparts]
crabman173 Offline
master

Registered: 01/01/06
Posts: 3534
Loc: Big Lick , North Carolina
SOLD!!!!!! Thanks Moparts!!440 FORGES SPEED PRO PISTONS NEW CHEAP!

I have a brand new set of TRW Speed Pro forged 440 pistons 030 over
These are flat tops , stock replacement, stock rod etc use 5/64ths stock type rings--Perfect for a cheapo 440 build--you can also spray the heck out of these indestructible slugs! Or..run forced induction $new at Summit etc near $400 I will take first $165 shipped FREE You can't beat this deal!!
Call or text me 704 244 6649 paypal OK
Thanks!!!


Attachments
pistons 003.JPG

Description: 9




Edited by crabman173 (08/05/17 07:08 AM)
_________________________
I have always had a fascination with fast cars at the expense of more normal character development

Top
#2348373 - 08/04/17 10:07 AM 1969 440 core from New Yorker [Re: moparts]
roadntrack Offline
enthusiast

Registered: 07/27/04
Posts: 376
Loc: USA
1969 Chrysler 440 from a New Yorker
block cast 1-17-69
stock un-cut bores
stock un-cut steel crank
906 heads
etc etc
have most parts to complete assy

$700 delivered to Nats
Send me a PM please


Attachments
MY PICS 031.jpg

MY PICS 028.jpg



Top
#2348601 - 08/04/17 05:26 PM Jones Cam Designs (Mike Jones) BB Solid Roller cam [Re: roadntrack]
BradH Offline
I Live Here

Registered: 01/30/03
Posts: 13210
Loc: Valhalla... eventually
This is a new BB solid roller from Jones Cam Designs (http://jonescams.com) intended for a fairly hot 440-ish c.i. street/strip application. It uses his inverse-radius endurance lobes and is spec'd at 259/261 at .050", .636"/.631", 109 LSA, .016" hot lash. These lobes can be used with up to 1.7 rockers, so you're not limited to running 1.5s.

I measured the lobes using .800"-wheel roller lifters in my 440 block:

Intake
Lobe - Duration
.0145 - 308 - - SAE duration @ .016" lash (.004" lobe lift above lash)
.020 - 295
.050 - 261 - - - 259 per cam card (increase from .800"-wheel vs .750"-wheel lifters)
.100 - 229
.200 - 180
.300 - 132
.400 - 57

Peak lift .424"
1.5 = .636"
1.6 = .678"

Exhaust
Lift - Duration
.0145 - 311 - - SAE duration @ .016" lash (.004" lobe lift above lash)
.020 - 297
.050 - 263 - - - 261 per cam card (increase from .800"-wheel vs .750"-wheel lifters)
.100 - 231
.200 - 181
.300 - 131
.400 - 54

Peak lift .421"
1.5 = .632"
1.6 = .674"


The cam is ground on a 109 LSA, and the suggested installed ICL is 106. Also, the #4 journal is grooved for full-time rocker shaft oiling, per my request when I ordered it.

It cost over $400, and Jones' cam prices have increased significantly since then. shock

The price is $330 shipped to the lower 48 US states. I accept USPS money orders and cash. Sorry, no PayPal or international sales.

Please PM me here, or text 7-zero-3 - 3-one-7 - 7-nine-8-seven... Thanks!


9.1.2017 - Someone asked what the build specs were provided to Jones Cams originally. Here's what I gave Mike Jones:

- Street/strip application
- 451 cubes
- 10.8 CR (93 E10 octane pump fuel)
- Ported Edelbrock Victor heads (std port, not MW)
- Single-plane intake w/ 950 4150 carb
- 2" headers w/ full 3" exhaust
- auto w/ 9.5" converter 4200-stall (4500 flash)
- 3800#s car & driver
- 4.10 gears & 28" tires
- max RPM 7000 (1/4 mile trap RPM)


Edited by BradH (09/01/17 01:32 PM)
_________________________
Life's too short to waste time on dumb@ss internet pi$$in' contests...

Living by the motto “It’s just easier to keep buying parts than bother with actually putting them together” since 2010… or was it 2000?

Top
#2348686 - 08/04/17 08:06 PM Edelbrock 6 carbs, Log style intake - Fits any big block [Re: Joesixpack]
HemiMark Offline
member

Registered: 10/13/05
Posts: 185
Loc: Pittsburgh, PA
440 log style Edelbrock intake, Polished and ready to install. comes with mounting bolts. Free delivery to Mopar Nationals $800.00 cash


Attachments
IMG_4802.JPG

IMG_4444.jpg




Edited by HemiMark (08/15/17 11:03 AM)

Top
#2349315 - 08/06/17 01:57 AM Re: Isky Adjustable Iron Rocker Arms, Shafts & Hardware - Used [Re: Rocket]
Turbo383 Offline
member

Registered: 02/19/07
Posts: 19
Loc: Florida
I'm interested in the rocker arms...

Top
Page 4 of 8 < 1 2 3 4 5 6 7 8 >

Advertisement
Sponsored Link
Forum Stats
24,898 Registered Members
32 Forums
184,215 Topics
2,134,037 Posts

Most users ever online: 882 @ 03/05/17 10:15 PM
Moparts Newest Topics
Cheap 2dr Valiant
by UCUDANT
Yesterday at 10:38 PM
What don't I get here??!! Help
by EV2 340
Yesterday at 10:25 PM
1970 Roadrunner Vin, title & radiator # on FB RM21N0A123482
by grancuda
Yesterday at 09:45 PM
weighted my car today
by mopar dave
Yesterday at 09:35 PM