Cam for 505 wedge - Moparts Forums

Register Log In Moparts Forums Unlawfl's Race & Engine Tech Cam for 505 wedge

Print Thread

Cam for 505 wedge #231536 02/21/09 05:20 PM 02/21/09 05:20 PM
Joined: Mar 2005 Posts: 3,138 Central NC gch OP master
gch OP master Joined: Mar 2005 Posts: 3,138 Central NC	While I may just as well end up with a custom ground solid I have always wanted to see how one of the Lunati Voodoo cams would perform. Motor in question is pump gas 505 10.5-1 ported e-heads sd intake w/850 HEAVY STREET CAR 4600lbs+ 3000 tight 10" likely 3.55 gears What rpm range could I expect out of the Voodoo 60305 284/292 242/252 @.050 .533/.552 110LS 106IC Just bench racing here.Is this a good fit for the intended usage and weight of car?I would like to see 5500 max rpm.Worth a try or much better to be had for similar money? I can go solid just as easy but if I can get close with a hyd and 1.6 rockers I am lazy.Hyd roller is not out of the question but pricey.

Re: Cam for 505 wedge [Re: gch] #231537 02/21/09 06:00 PM 02/21/09 06:00 PM
Joined: Jul 2005 Posts: 8,647 ELYRIA,OH B blownzoom440
blownzoom440 B Joined: Jul 2005 Posts: 8,647 ELYRIA,OH	will you use headers?exh size,length? what tire HT? just wondering. 5042325-100_1950.jpg (63 downloads) Last edited by METAL STORM; 02/21/09 06:33 PM.

Re: Cam for 505 wedge [Re: blownzoom440] #231538 02/21/09 06:03 PM 02/21/09 06:03 PM
Joined: Mar 2005 Posts: 3,138 Central NC gch OP master
gch OP master Joined: Mar 2005 Posts: 3,138 Central NC	1 7/8 tti(save the 2" bashing) and 3" exhaust.28" tire.This is a C body cruiser/sleeper.

Re: Cam for 505 wedge [Re: gch] #231539 02/21/09 06:07 PM 02/21/09 06:07 PM
Joined: Jul 2005 Posts: 8,647 ELYRIA,OH B blownzoom440
blownzoom440 B Joined: Jul 2005 Posts: 8,647 ELYRIA,OH	Quote: 1 7/8 tti(save the 2" bashing) and 3" exhaust.28" tire.This is a C body cruiser/sleeper. so you may be looking for 550/600HP and a lot of TQ. 5042343-100_1951.jpg (56 downloads) Last edited by METAL STORM; 02/21/09 06:36 PM.

Re: Cam for 505 wedge [Re: blownzoom440] #231540 02/21/09 06:14 PM 02/21/09 06:14 PM
Joined: Jan 2003 Posts: 9,870 Weddington, N.C. Streetwize master
Streetwize master Joined: Jan 2003 Posts: 9,870 Weddington, N.C.	Geoarge, The comp 305 magnum works very well for what you're building.....but I'd be tempted to run the XE 241/247 cause I know that works really well in a heavy 440 car....like high 11's with e-heads and 3.23 gears. If the Lunati is like the old 240/250 .520/.547 I ran in a 451 low deck that would be a good one too. WIZE World's Quickest Diahatsu Rocky (??) 414" Stroker Small block Mopar Powered. 10.84 @ 123...and gettin' quicker! https://www.youtube.com/watch?v=-mWzLma3YGI In Car: https://www.youtube.com/watch?v=PjXcf95e6v0

Re: Cam for 505 wedge [Re: Streetwize] #231541 02/21/09 08:31 PM 02/21/09 08:31 PM
Joined: Mar 2005 Posts: 3,138 Central NC gch OP master
gch OP master Joined: Mar 2005 Posts: 3,138 Central NC	Quote: Geoarge, The comp 305 magnum works very well for what you're building.....but I'd be tempted to run the XE 241/247 cause I know that works really well in a heavy 440 car....like high 11's with e-heads and 3.23 gears. If the Lunati is like the old 240/250 .520/.547 I ran in a 451 low deck that would be a good one too. 600hp would be nice but my intake/carb may limit the hp potential at 505c.i. 550 hp an 600lb ft from 2500-5000 would push the barn with wheels pretty good I believe. Thanks for the input Bobby and the simulation METAL STORM. Any areas for signifigant improvement?The intake has been ported(mild) and I am limited on hood clearance(no rpm)unless I cut the hood and redneck it with the tunnel ram I have.

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1