Page 4 of 5 < 1 2 3 4 5 >
Topic Options
#2428512 - 01/03/18 06:50 PM Re: My gen 3 project [Re: joshking440]
joshking440 Offline
Lunch is on me!

Registered: 10/18/06
Posts: 4528
Loc: Indy
it’s same mopar offset as my big block was.

The car started as a big block 727 then I swapped that out for a t400. When I went gen 3 I stuck the t400 back in the car and mounted the engine the motorplate ended up with in .090 of where it used to be. So I added a mid plate and pushed it forward

Top
#2429437 - 01/05/18 11:11 AM Re: My gen 3 project [Re: joshking440]
joshking440 Offline
Lunch is on me!

Registered: 10/18/06
Posts: 4528
Loc: Indy
try again


Attachments
IMG_0499.jpg

IMG_0501.jpg

IMG_0531.jpg

IMG_0500.jpg




Edited by joshking440 (01/05/18 12:06 PM)

Top
#2429443 - 01/05/18 11:25 AM Re: My gen 3 project [Re: joshking440]
joshking440 Offline
Lunch is on me!

Registered: 10/18/06
Posts: 4528
Loc: Indy
.


Attachments
IMG_0493.jpg

IMG_0494.jpg

IMG_0495.jpg

IMG_0496.jpg



Top
#2429444 - 01/05/18 11:27 AM Re: My gen 3 project [Re: joshking440]
joshking440 Offline
Lunch is on me!

Registered: 10/18/06
Posts: 4528
Loc: Indy
..


Attachments
IMG_0497.jpg

IMG_0498.jpg

IMG_0499.jpg

IMG_0501.jpg



Top
#2429447 - 01/05/18 11:36 AM Re: My gen 3 project [Re: joshking440]
joshking440 Offline
Lunch is on me!

Registered: 10/18/06
Posts: 4528
Loc: Indy
well that was painful - but we got them up

Top
#2429449 - 01/05/18 11:48 AM Re: My gen 3 project [Re: daryld]
joshking440 Offline
Lunch is on me!

Registered: 10/18/06
Posts: 4528
Loc: Indy
Originally Posted By daryld
Which dipstick set up is that?


milodon

Top
#2429454 - 01/05/18 12:08 PM Re: My gen 3 project [Re: joshking440]
ric3xrt Offline
super stock

Registered: 01/13/06
Posts: 988
Loc: Trumbauersville PA
just Amazing , can't wait till it's done.
_________________________
Truth has no agenda, but those with an agenda don't always acknowledge truth
74 D100 D-Code,3x75 D100 D-code, 3x77 D100 D-code,6x78 D150 D-D-code...lots of pre 81 trucks
75 4x2 Ramcharger....G3 coming soon
2003 Ram st
2004 Rumble Bee
2004 Ram GTX(Plum Crazy)
2005 Ram GTXtreme(s Plum Crazy,Banana Yellow)
Any info on these trucks is greatly appreciated
2005 Ram 1500 (drag truck in building)
2014 1500 tradesman(shhhh, it's hiding a 7.0 short block under those eagle heads.

Top
#2429694 - 01/05/18 08:47 PM Re: My gen 3 project [Re: joshking440]
kpzbee Offline
super stock

Registered: 01/20/03
Posts: 882
Loc: Wooster, Ohio
Spectacular! up
_________________________
"It's funny how one project eventually leads (or forces) you into another one.
It's really just one endless project designed to induce insanity and bankruptcy."

Top
#2429877 - 01/06/18 10:23 AM Re: My gen 3 project [Re: joshking440]
Just-a-dart Offline
super stock

Registered: 02/20/11
Posts: 1148
Loc: Glendora Ca.
Thanks for takimg the time to post up the pics. Combo looks sweet!
_________________________

"Just a Bracket car dressed up like a streetcar"

Top
#2431036 - 01/08/18 10:52 AM Re: My gen 3 project [Re: joshking440]
onig Offline
enthusiast

Registered: 07/09/08
Posts: 331
Loc: Canada
Great pics.
Do you have any of how the turbo is supported?
_________________________
69 Dart, The BB is now gone, Soon to be Gen 3 Hemi...

Top
#2431038 - 01/08/18 10:55 AM Re: My gen 3 project [Re: onig]
joshking440 Offline
Lunch is on me!

Registered: 10/18/06
Posts: 4528
Loc: Indy
Originally Posted By onig
Great pics.
Do you have any of how the turbo is supported?


Right now they are just hanging on the exhaust. I’m waiting on some
trick billet turbo mounts from Maven Performance Should be here today or tomorrow then I’ll get you some pictures once they are locked in.

Top
#2475206 - 04/01/18 08:06 AM Re: My gen 3 project [Re: joshking440]
joshking440 Offline
Lunch is on me!

Registered: 10/18/06
Posts: 4528
Loc: Indy
Making headway.

Driveshaft loop/trans crossmember is in. Driveshaft is in. Remade the motorplate and working on getting the exhaust off the turbos handled.

The car goes Wednesday to have intercoolers plumbed and cold side plumbing finished up.

Then engine bay paint and reassembly. It’s starting to feel like there’s an end in sight.



Attachments
april - 1.jpg

april - 2.jpg

april - 3.jpg

april - 4.jpg




Edited by joshking440 (04/01/18 11:37 AM)

Top
#2475252 - 04/01/18 10:09 AM Re: My gen 3 project [Re: joshking440]
ric3xrt Offline
super stock

Registered: 01/13/06
Posts: 988
Loc: Trumbauersville PA
Like the engine plate...I get goose bumps every time I see this project.
_________________________
Truth has no agenda, but those with an agenda don't always acknowledge truth
74 D100 D-Code,3x75 D100 D-code, 3x77 D100 D-code,6x78 D150 D-D-code...lots of pre 81 trucks
75 4x2 Ramcharger....G3 coming soon
2003 Ram st
2004 Rumble Bee
2004 Ram GTX(Plum Crazy)
2005 Ram GTXtreme(s Plum Crazy,Banana Yellow)
Any info on these trucks is greatly appreciated
2005 Ram 1500 (drag truck in building)
2014 1500 tradesman(shhhh, it's hiding a 7.0 short block under those eagle heads.

Top
#2475352 - 04/01/18 11:38 AM Re: My gen 3 project [Re: joshking440]
joshking440 Offline
Lunch is on me!

Registered: 10/18/06
Posts: 4528
Loc: Indy
Few More


Attachments
april - 5.jpg

april - 6.jpg

april - 7.jpg

april - 8.jpg



Top
#2475362 - 04/01/18 11:53 AM Re: My gen 3 project [Re: ric3xrt]
joshking440 Offline
Lunch is on me!

Registered: 10/18/06
Posts: 4528
Loc: Indy
Originally Posted By ric3xrt
Like the engine plate...I get goose bumps every time I see this project.


Thanks man. Its been an interesting journey so far... hope it performs as well as it looks... only time will tell

Top
#2475385 - 04/01/18 12:33 PM Re: My gen 3 project [Re: joshking440]
WO23Coronet Offline
master

Registered: 01/08/08
Posts: 4010
Loc: Canada
Wow, are there any cast parts on that engine lol? Looks great, unreal workmanship with all that billet

Top
#2475973 - 04/02/18 09:51 AM Re: My gen 3 project [Re: joshking440]
Quickrunner Offline
mopar

Registered: 03/10/10
Posts: 489
Loc: Indianapolis In. usa
Looking good Josh!
_________________________
05 Ram 1500 Daytona package
71 Demon Gen3 hemi drag radial project
2004 Jeep Liberty
09 Challenger R/T 6spd

Missin' my 9 second 70 runner!

Top
#2476192 - 04/02/18 02:35 PM Re: My gen 3 project [Re: Quickrunner]
Twostick Offline
master

Registered: 05/20/03
Posts: 4859
Loc: Downtown Roebuck Ont
Originally Posted By Quickrunner
Going through this right now with a Reid case 400 in my 71 demon build. The floor will need modified for the 400 with a GV on it. they have one for a TF that will fit with "dings" in the floor pan but it has a super long tailshaft adaptor I didn't care for and I wanted a aftermarket SFI case so I didn't need to mess with shields.


They have a short 727 version of the GV that uses the short truck/MH trans output shaft. Shortens the overall length about 10" IIRC.

Kevin

Top
#2476614 - 04/03/18 12:19 AM Re: My gen 3 project [Re: joshking440]
joshking440 Offline
Lunch is on me!

Registered: 10/18/06
Posts: 4528
Loc: Indy
Got the radiator and Fan to fit. Barely.


Attachments
6A173E0E-E11A-4558-A2B2-8EA24E459B15.jpeg



Top
#2476734 - 04/03/18 11:08 AM Re: My gen 3 project [Re: joshking440]
jdralph Offline
member

Registered: 05/20/10
Posts: 19
Loc: texas
very nice

Top
Page 4 of 5 < 1 2 3 4 5 >

Advertisement
Sponsored Link
Forum Stats
25,256 Registered Members
32 Forums
188,971 Topics
2,203,743 Posts

Most users ever online: 882 @ 03/05/17 10:15 PM
Moparts Newest Topics
Thunderboats - Miss Budweiser, Miss Bardahl, etc.
by RM21N0A
19 minutes 44 seconds ago
1971 Plymouth roadrunner
by FM3_1970
24 minutes 8 seconds ago
New Yorker diff fluid
by TheCrystalShip
Today at 06:04 PM
Denso 1 wire?
by RV2
Today at 05:35 PM