500 inch Mopar Build - Which intake to go with? - Moparts Forums

Register Log In Moparts Forums Unlawfl's Race & Engine Tech 500 inch Mopar Build - Which intake to go with?

Print Thread

Page 1 of 2

1

2

500 inch Mopar Build - Which intake to go with? #197970 01/19/09 12:08 PM 01/19/09 12:08 PM
Joined: Jul 2005 Posts: 14 BC, Canada D D200 OP member
D200 OP member D Joined: Jul 2005 Posts: 14 BC, Canada	I'm looking to get my 68 barracuda in the 11s so i've built a 500" bb stroker. I'm using stealth aluminum heads, the 557 lift mopar cam, and expect to use the car mostly on the street but it will see the track occassionally. I haven't picked up the carb yet but expect to go with the 1050 dominator. Opinions please from those who have done this? Stick with the traditional torker II or ??

Re: 500 inch Mopar Build - Which intake to go with? [Re: D200] #197971 01/19/09 12:19 PM 01/19/09 12:19 PM
A Anonymous Unregistered
Anonymous Unregistered A	hi there, I have a 400 stroked to a 515 ci from 440 source, i too have the stealth heads. I also think i m close to the 560 lift as well. I ll be using the toker II intake on my set up. Your barcuda is alot lighter then my 74 charger. So you should get moving pretty quick. I d suggest on at least a 3500 rpm stall TQ in the tranny. As for carbs, well i have a few choices, a 650 holley, and an 850 demon. But i may have to get something bigger. If you have any pics send them over to my e mail.

Re: 500 inch Mopar Build - Which intake to go with? [Re: D200] #197972 01/19/09 12:27 PM 01/19/09 12:27 PM
Joined: Jun 2003 Posts: 52,972 Romeo MI MR_P_BODY Master
MR_P_BODY Master Joined: Jun 2003 Posts: 52,972 Romeo MI	Look for a larger plenum, as your CI goes up you need to increase plenum volume also

Re: 500 inch Mopar Build - Which intake to go with? [Re: D200] #197973 01/19/09 01:25 PM 01/19/09 01:25 PM
Joined: Jan 2003 Posts: 2,930 Odessa, Tx. cudarex master
cudarex master Joined: Jan 2003 Posts: 2,930 Odessa, Tx.	Holley Street Dominator is a good one if your not going max wedge ports.

Re: 500 inch Mopar Build - Which intake to go with? [Re: D200] #197974 01/19/09 01:36 PM 01/19/09 01:36 PM
Joined: Mar 2005 Posts: 3,138 Central NC gch master
gch master Joined: Mar 2005 Posts: 3,138 Central NC	Quote: I'm looking to get my 68 barracuda in the 11s so i've built a 500" bb stroker. I'm using stealth aluminum heads, the 557 lift mopar cam, and expect to use the car mostly on the street but it will see the track occassionally. I haven't picked up the carb yet but expect to go with the 1050 dominator. Opinions please from those who have done this? Stick with the traditional torker II or ?? I would think a single plane is in order.Which one depends on wheather you want a dominator flange or a 4150 flange.If you have the hood clearance some say a 4150 flange with a dommy adapter works well. I would think a victor would fill the bill with enough gear and converter.Others likely have more experience with dominators and no what intakes work best. BTW you should be well into the 10's with some traction.

Re: 500 inch Mopar Build - Which intake to go with? [Re: gch] #197975 01/19/09 02:04 PM 01/19/09 02:04 PM
Joined: Sep 2005 Posts: 2,442 LOWELL IN Q QWK_ENUF top fuel
QWK_ENUF top fuel Q Joined: Sep 2005 Posts: 2,442 LOWELL IN	two words TUNNEL RAM WAXER

Re: 500 inch Mopar Build - Which intake to go with? [Re: QWK_ENUF] #197976 01/19/09 02:20 PM 01/19/09 02:20 PM
Joined: May 2004 Posts: 12,383 Taxes & Virus's R-US, NY Dragula I Live Here
Dragula I Live Here Joined: May 2004 Posts: 12,383 Taxes & Virus's R-US, NY	Quote: two words TUNNEL RAM X2 '70 Cuda,...605 EFI Hemi Street Car (6.20 best pass, 1.33 60ft) https://www.youtube.com/watch?v=WYw6RA-k5Bk (6.25 at 108.75mph from inside car) https://www.youtube.com/watch?v=3zQEb9uxFng (6.25 at 108mph from outside car) https://www.youtube.com/watch?v=JCvfzsC4NgM (9.9) '66 Barracuda AWB Stretched nose Blown 440 Car in build stage '71 Duster Drag Car 400 Low Deck 512 best 6.002 at 115.44mph https://www.youtube.com/watch?v=Znuo3jMUXTk

Re: 500 inch Mopar Build - Which intake to go with? [Re: D200] #197977 01/19/09 03:05 PM 01/19/09 03:05 PM
Joined: Jan 2003 Posts: 30,992 Oregon A AndyF I Win
AndyF I Win A Joined: Jan 2003 Posts: 30,992 Oregon	B or RB motor? There is one choice for the B motor and three choices for the RB motor if you want to run a Dominator on standard port heads. The Mopar Performance M1 intake with the 4500 flange is a great intake and is fairly low profile. The M1 intake is avaiable for both the B or the RB motor. For the RB motors, the Edelbrock Super Victor with std ports is an excellent intake but it is pretty tall. There is also a Weiand Team G intake with the 4500 flange but it is kind of a funky intake with big notches in the inner runners. If it was my engine I'd go with the MP M1 intake. 725 for the RB or 724 for the B motor. They work great, they're cheap and the they look pretty good.

Re: 500 inch Mopar Build - Which intake to go with? [Re: D200] #197978 01/19/09 03:08 PM 01/19/09 03:08 PM
Joined: Jan 2003 Posts: 30,992 Oregon A AndyF I Win
AndyF I Win A Joined: Jan 2003 Posts: 30,992 Oregon	Here is the M1 intake with a 4500 flange. This is on my 505 motor that has CNC ported Mopar heads. 680 hp with a street roller cam. This setup would make a killer street/strip combo if you can afford the race gas!

Re: 500 inch Mopar Build - Which intake to go with? [Re: D200] #197979 01/19/09 03:19 PM 01/19/09 03:19 PM
Joined: Feb 2006 Posts: 1,949 land of 10,000______'s B BDS871Cuda top fuel
BDS871Cuda top fuel B Joined: Feb 2006 Posts: 1,949 land of 10,000______'s	Quote: I'm looking to get my 68 barracuda in the 11s so i've built a 500" bb stroker. I'm using stealth aluminum heads, the 557 lift mopar cam, and expect to use the car mostly on the street but it will see the track occassionally. I haven't picked up the carb yet but expect to go with the 1050 dominator. Opinions please from those who have done this? Stick with the traditional torker II or ?? I've put a 4000 lb car deep in the 11's with only 440 cubes, 452 iron heads and a 825 race Demon carb. Your combo could get buy with less carb. If you want the big carb, I would give it more cam. The M-1 works real good. Which ever way you go, your car should run 10's easy with tuning and track time. Yes mine was a daily street driver. Snap your neck, mega G-force launch, is all I want!

Re: 500 inch Mopar Build - Which intake to go with? [Re: D200] #197980 01/19/09 04:54 PM 01/19/09 04:54 PM
Joined: Nov 2005 Posts: 690 New Hampshire, USA O oldiron mopar
oldiron mopar O Joined: Nov 2005 Posts: 690 New Hampshire, USA	Had good success w/431 & E Heads (prepped by Dwayne Porter) Edelbrock RPM manifold, 1 inch spacer, 950 Holley, 4.10 gears Works pretty good in a heavy stick car Hope this helps 66 Belvedere Vert, 4 Speed/Jerico, slowly, very slowly, getting faster - NA LD Wedge New New Best: 10.56 @129 68 B'cuda 4 gear Jerico - Another New Best of 9.86 & Trying to slow up https://www.youtube.com/watch?v=T4jDLKwd9Gs

Re: 500 inch Mopar Build - Which intake to go with? [Re: oldiron] #197981 01/19/09 05:10 PM 01/19/09 05:10 PM
Joined: Nov 2003 Posts: 6,293 Rock Springs Bob_Coomer master
Bob_Coomer master Joined: Nov 2003 Posts: 6,293 Rock Springs	This would be a great candidate for the Big duel plane intake that Indy offers. and would complement that cam shaft well. This intake can be open'd up to max wedge window down the road too. It blows away about any duel plan intake there is, and made more power than about any traditional single plan too.. It crucified the other intake in mid range torque. I just dont think the larger Victor, style high rise intakes would work well with those heads, and camshaft. You will never see the rpm it takes to make them run. [color:"red"]65 Hemi Belvedere coming soon [/color] [color:"#00FF00"]557" Indy engine 1.07 60ft 144mph in the 8th 2100 lbs package [/color]

Re: 500 inch Mopar Build - Which intake to go with? [Re: Bob_Coomer] #197982 01/19/09 05:48 PM 01/19/09 05:48 PM
Joined: Mar 2008 Posts: 5,746 Ontario, Canada Dodgem master
Dodgem master Joined: Mar 2008 Posts: 5,746 Ontario, Canada	I second the big dual plane indy offers. best out there for street strip!

Re: 500 inch Mopar Build - Which intake to go with? [Re: D200] #197983 01/19/09 08:49 PM 01/19/09 08:49 PM
Joined: Feb 2005 Posts: 4,310 Prospect, PA BSB67 master
BSB67 master Joined: Feb 2005 Posts: 4,310 Prospect, PA	For a 4150 carb , I recommend either the Indy 2D or the holley SD. On the dyno they were pretty close to each other on my 500" engine in the 550 to 580 hp range. If you use the Dommy - I don't know. If you use the Indy 2D with a Dommy and adapter, you'll have hood clearance issues, possibly not with the SD. My

Re: 500 inch Mopar Build - Which intake to go with? [Re: BSB67] #197984 01/19/09 08:56 PM 01/19/09 08:56 PM
Joined: Nov 2003 Posts: 6,293 Rock Springs Bob_Coomer master
Bob_Coomer master Joined: Nov 2003 Posts: 6,293 Rock Springs	Well my opinion isnt worth much, but you can have it for free.. The reason I would not go with the Victor or any other High rise intake is that the motor is mostly street, and that engine and cam wont RPM very high. Im guessing 5600-5800 and she's all done. Those intakes just work better on 6K and higher engines, but the good side is that if you do use one of those intakes, it might hook better on the street, do to the loss in torque.. The Holley SD would be a good intake, and If I could pick one up fairly cheap...that would be the way to go also. [color:"red"]65 Hemi Belvedere coming soon [/color] [color:"#00FF00"]557" Indy engine 1.07 60ft 144mph in the 8th 2100 lbs package [/color]

Re: 500 inch Mopar Build - Which intake to go with? [Re: Bob_Coomer] #197985 01/19/09 11:07 PM 01/19/09 11:07 PM
Joined: Jan 2003 Posts: 9,872 Weddington, N.C. Streetwize master
Streetwize master Joined: Jan 2003 Posts: 9,872 Weddington, N.C.	The Indy dual plane on a 500 inch motor is a very stout piece, especially in MW form and with a big carb!! But in a light cuda a single plane may help a bit by actually taking off a little upper bottom (if you can't hook it up) to make the car more tractible. Last edited by Streetwize; 01/19/09 11:09 PM. WIZE World's Quickest Diahatsu Rocky (??) 414" Stroker Small block Mopar Powered. 10.84 @ 123...and gettin' quicker! https://www.youtube.com/watch?v=-mWzLma3YGI In Car: https://www.youtube.com/watch?v=PjXcf95e6v0

Re: 500 inch Mopar Build - Which intake to go with? [Re: D200] #197986 01/19/09 11:17 PM 01/19/09 11:17 PM
Joined: Jan 2003 Posts: 2,567 Appalachia RedRam master
RedRam master Joined: Jan 2003 Posts: 2,567 Appalachia	getting a 500" Abody cuda into the 11's would be no problem. I used a M1 single plane and a ThermoQuad on a mild 493" to get a long wheel base truck into the mid 11's with a 3.31 gear.

Re: 500 inch Mopar Build - Which intake to go with? [Re: RedRam] #197987 01/20/09 02:08 AM 01/20/09 02:08 AM
Joined: Sep 2008 Posts: 2,840 Flint, Michigan B1Fish540 master
B1Fish540 master Joined: Sep 2008 Posts: 2,840 Flint, Michigan	wow Red Ram that truck really hauls with that TQ! Nice! Does anybody have any comparisons between the M1 and the big Indy dual plane. I kind of boiled it down between those two. I have an M1 but my 500 inch stroker might like the dual plane better as it will be in a heavy car.(Challenger)

Re: 500 inch Mopar Build - Which intake to go with? [Re: B1Fish540] #197988 01/20/09 10:09 AM 01/20/09 10:09 AM
Joined: Mar 2008 Posts: 5,746 Ontario, Canada Dodgem master
Dodgem master Joined: Mar 2008 Posts: 5,746 Ontario, Canada	Bunch of stuff hear! http://www.moparmusclemagazine.com/techarticles/mopp_0701_mopar_intake_manifold/index.html Hughes used to have some good articles with floe numbers but links no longer work and they seem gone from sight

Re: 500 inch Mopar Build - Which intake to go with? [Re: Dodgem] #197989 01/20/09 11:12 AM 01/20/09 11:12 AM
Joined: Jul 2005 Posts: 1,472 Overland Park, KS. J Joshs68 pro stock
Joshs68 pro stock J Joined: Jul 2005 Posts: 1,472 Overland Park, KS.	I like my M1

Page 1 of 2

1

2

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1