CUDA SHAKER BUBBLE EMBLEMS 440-6 - Moparts Forums

Register Log In Moparts Forums Moparts Restoration & A12 Forum CUDA SHAKER BUBBLE EMBLEMS 440-6

Print Thread

Page 1 of 2

1

2

CUDA SHAKER BUBBLE EMBLEMS 440-6 #195464 01/16/09 07:52 PM 01/16/09 07:52 PM
Joined: Jul 2005 Posts: 1,169 Richmond, VA R rayztoy OP super stock
rayztoy OP super stock R Joined: Jul 2005 Posts: 1,169 Richmond, VA	Hi, Are these correct NOS? Please check the link. Thanks! Ray http://cgi.ebay.com/ebaymotors/1970-1971...itemZ7994022972

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 [Re: rayztoy] #195465 01/16/09 07:56 PM 01/16/09 07:56 PM
Joined: Mar 2005 Posts: 1,022 Green Lane, PA sawdust super stock
sawdust super stock Joined: Mar 2005 Posts: 1,022 Green Lane, PA	Cuda 440 six barrel shaker emblems were tapered from what I can remember. The text was tapered from front to back is what I mean, kind of to follow the bubble. May be wrong but this is what I had seen in the past as the difference between shaker and rally hood emblems.

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 [Re: rayztoy] #195466 01/16/09 07:58 PM 01/16/09 07:58 PM
Joined: Jan 2003 Posts: 4,782 Ontario, Canada mccannix master
mccannix master Joined: Jan 2003 Posts: 4,782 Ontario, Canada	Brushed finish on the 'cuda' part of the nameplate or chrome finish??? That will answer your question.... BTW rallye hood emblems have two pins not three.

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 [Re: mccannix] #195467 01/16/09 08:11 PM 01/16/09 08:11 PM
Joined: Jul 2005 Posts: 1,169 Richmond, VA R rayztoy OP super stock
rayztoy OP super stock R Joined: Jul 2005 Posts: 1,169 Richmond, VA	The ones in the link are chrome finish on the CUDA name, whereas my original ones are brushed on the CUDA name. My originals also have the 3 pins. Are there any repros that are like the originals?

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 [Re: rayztoy] #195468 01/16/09 08:18 PM 01/16/09 08:18 PM
Joined: Dec 2005 Posts: 335 Olympia WA R rocketresto enthusiast
rocketresto enthusiast R Joined: Dec 2005 Posts: 335 Olympia WA	Those are repo. I bought a set and was very dissapointed Mike

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 [Re: rayztoy] #195469 01/16/09 08:21 PM 01/16/09 08:21 PM
A Anonymous Unregistered
Anonymous Unregistered A	Thats Frank Mitchell and his chromed repops.Like mentioned earlier,they originally had a brushed finish on the "Cuda".I heard he had the original company in the Detroit area remake all these "NOS" emblems,but they could not dulpicate the brushed finish any more.Either a cost problem or EPA problem I heard

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 [Re: rayztoy] #195470 01/16/09 10:26 PM 01/16/09 10:26 PM
A Anonymous Unregistered
Anonymous Unregistered A	nos 2 pin emblem just showing the brushed finish 4953112-100_0078.JPG (284 downloads)

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 #195471 01/18/09 11:32 AM 01/18/09 11:32 AM
Joined: Jan 2003 Posts: 1,267 midwest S sg333e super street
sg333e super street S Joined: Jan 2003 Posts: 1,267 midwest	Can you guys confirm which ones are correct, original pieces? The two pin version? Did all shakers come with three holes? Hobbies and associated message boards: 1970 Cuda 440+6 FE5 H6X9 4 SP> Moparts.com 1987 Grand National (422rwhp/566tq)> TurboBuick.com 2008 BMW 335 TT 6MT> E90Post.com 2008 Gary Fisher HiFi Plus 29er > MTBR.com 2008 German Shorthair Pointer > Shorthairs.net

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 [Re: sg333e] #195472 01/18/09 01:44 PM 01/18/09 01:44 PM
Joined: Jul 2005 Posts: 1,169 Richmond, VA R rayztoy OP super stock
rayztoy OP super stock R Joined: Jul 2005 Posts: 1,169 Richmond, VA	My original shaker setup has 3 holes in the bubble, 3 pins with speednuts on the brushed CUDA emblem. Anyone repopping them correctly?

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 [Re: rayztoy] #195473 01/18/09 09:28 PM 01/18/09 09:28 PM
Joined: Dec 2005 Posts: 1,495 Fort Workin Tx Day2Runner pro stock
Day2Runner pro stock Joined: Dec 2005 Posts: 1,495 Fort Workin Tx	Quote: My original shaker setup has 3 holes in the bubble, 3 pins with speednuts on the brushed CUDA emblem. Anyone repopping them correctly? mines the same and NO

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 [Re: Day2Runner] #195474 01/18/09 10:34 PM 01/18/09 10:34 PM
Joined: Jan 2003 Posts: 3,000 Long Island, NY shakerjoe master
shakerjoe master Joined: Jan 2003 Posts: 3,000 Long Island, NY	my shaker has 3 holes, but when I picked up the car in 1994, it only had 1 callout on it, with 2 prongs. I picked up a few NOS ones, but they were 2 prong emblems also. I've never seen a 3 prong emblem in person - but all the ones I have are brushed, not shiny. I'm sure my shaker bubble is original - looks like it has some time on the job, has some of the over spray on the underside, part #, and is in pretty used condition, and as far as I know, the repro's weren't out yet - Joe

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 [Re: sg333e] #195475 01/18/09 10:45 PM 01/18/09 10:45 PM
Joined: Jan 2006 Posts: 2,368 White Plains, NY VCODE top fuel
VCODE top fuel Joined: Jan 2006 Posts: 2,368 White Plains, NY	Quote: Can you guys confirm which ones are correct, original pieces? The two pin version? Did all shakers come with three holes? My 2 shaker cuda's have 3 holes with 3 pin emblems Bob 4957528-shaker%20numbersA.jpg (284 downloads) Mom & Dad let me buy a brand new 70 Challenger R/T 440 Six-Pack Super Trac Pack when I was 17 (Robert what is a 440 Six-Pack)

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 [Re: VCODE] #195476 01/19/09 12:42 AM 01/19/09 12:42 AM
Joined: Jan 2003 Posts: 42,714 Spokane Washington ScottSmith_Harms Mr Wizzard
ScottSmith_Harms Mr Wizzard Joined: Jan 2003 Posts: 42,714 Spokane Washington	All factory installed emblems were 3 pin and brushed

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 [Re: ScottSmith_Harms] #195477 01/20/09 02:00 AM 01/20/09 02:00 AM
Joined: Mar 2003 Posts: 1,039 INDIANA P Paul Jacobs super stock
Paul Jacobs super stock P Joined: Mar 2003 Posts: 1,039 INDIANA	Scott, As the above poster was saying, I too took apart a real early built shaker (9-69) and it had 2 pin emblems in it (though it was drilled for three). It was an orig paint bubble, but whats the story on the emblems? Possible supply issue with the 3 pin ones and they threw on some 2 pin emblems instead? After all 2 pins are very commonplace but finding the real 3 pins is tough!

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 [Re: Paul Jacobs] #195478 01/20/09 03:16 AM 01/20/09 03:16 AM
Joined: Jan 2003 Posts: 42,714 Spokane Washington ScottSmith_Harms Mr Wizzard
ScottSmith_Harms Mr Wizzard Joined: Jan 2003 Posts: 42,714 Spokane Washington	Paul I understand the "Never say never" deal but I'm gonna have to call you on that one, I know that you know your stuff but I've seen dozens of original bubbles on and off cars, never seen a factory one wearing 2 pin emblems. I'd guess they were replaced somewhere along the line (obviously a simple swap). Do you have any quality photos of your discoveries?

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 [Re: ScottSmith_Harms] #195479 01/20/09 09:38 AM 01/20/09 09:38 AM
Joined: Jan 2003 Posts: 2,984 Montreal,Quebec,Canada J JulesdaWiperman super gas
JulesdaWiperman super gas J Joined: Jan 2003 Posts: 2,984 Montreal,Quebec,Canada	I wish I had a few dozen of these and not just the one I got from a garage clearout. I sold it last year to a moparts member. Jules 4960462-a(8).jpg (317 downloads)

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 [Re: JulesdaWiperman] #195480 01/20/09 01:29 PM 01/20/09 01:29 PM
Joined: Jan 2003 Posts: 4,782 Ontario, Canada mccannix master
mccannix master Joined: Jan 2003 Posts: 4,782 Ontario, Canada	Shaker nameplates were all applied to the scoop by Fram before packaging the assembled units, sent via bedsteads to Hamtramck assembly. The only nameplates they had in their facility were the 3 prong since that is all they dealt with. As with Jules' photo, its always nice to have the original packaging to back up the real deal verses the all chrome repros. 4960774-shakername.jpg (116 downloads)

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 [Re: mccannix] #195481 01/21/09 07:46 AM 01/21/09 07:46 AM
Joined: Nov 2004 Posts: 1,923 Medina, Ohio HEMICUDA top fuel
HEMICUDA top fuel Joined: Nov 2004 Posts: 1,923 Medina, Ohio	Quote: Shaker nameplates were all applied to the scoop by Fram before packaging the assembled units, sent via bedsteads to Hamtramck assembly. The only nameplates they had in their facility were the 3 prong since that is all they dealt with. As with Jules' photo, its always nice to have the original packaging to back up the real deal verses the all chrome repros. Terry, we ready to get everyone jacked up yet about the shaker adapter rings? Come on, it will be fun and I think we owe it to all our friends here on the board. If you start it I'll post pictures with you of my examples.

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 [Re: HEMICUDA] #195482 01/21/09 11:08 PM 01/21/09 11:08 PM
Joined: Mar 2003 Posts: 1,039 INDIANA P Paul Jacobs super stock
Paul Jacobs super stock P Joined: Mar 2003 Posts: 1,039 INDIANA	Scott & Terry, Thanks for the info on the emblems. The reason I was asking is because in the parts manual, specifically under shaker hood (sec23) it gives the emblem part number as 2998798, which is pictured-a 2 pin emblem. 4964620-nameplate.JPG (204 downloads)

Re: CUDA SHAKER BUBBLE EMBLEMS 440-6 [Re: Paul Jacobs] #195483 01/21/09 11:14 PM 01/21/09 11:14 PM
Joined: Mar 2003 Posts: 1,039 INDIANA P Paul Jacobs super stock
Paul Jacobs super stock P Joined: Mar 2003 Posts: 1,039 INDIANA	the book 4964639-IL23-147.jpg (203 downloads)

Page 1 of 2

1

2

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1